ALUMINUM MATRIX COMPOSITES BASED ON CASTING ALUMINUM ALLOYS WITH OXIDES AND CARBIDES
Open Access
- 5 March 2025
- journal article
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Casting Processes
- Vol. 159 (1) , 48-64
Abstract
The paper considers the technological features of obtaining as-cast aluminum matrix composite materials (AMC), reinforced by oxide and carbide particles Al2O3, ZrO2, TiO2, SiC, B4C and WC. Because of the development of active mixing casting, in-situ synthesis, friction stirring, etc. methods, high-quality composites with favorable structural characteristics and a high level of mechanical properties can be created and obtained. Among many considered methods of obtaining as-cast aluminum matrix composites, one of the most universal and widely used are melt active mixing casting and injection molding. The first method is universal for stirring and distributing reinforcing particles, and the second allows to minimize structure defects and porosity. It has been shown that high dispersion of oxide and carbide additives often leads to negative consequences – defects of non-integration and powders agglomeration. Large particles of reinforcing components, in turn, lead to the formation of pores. Better absorption of powder additives by increasing their wettability ensures by several methods, among which the most effective are their preheating, surface activation, or adding magnesium to the aluminum melt in an amount of up to 1 wt. %. The vast majority of studies are devoted to the creation of AMC based on the A356 alloy. The most popular additives in this case are Al2O3, ZrO2, SiC, B4C and WC. The optimal content of fillers for most of the studied compositions is about 2-6 wt. %. The optimal particle size is within 5-35 microns, which is expressed in an increase in the hardness of the composites. A larger particle size has little effect on the mechanical properties of the alloys, and nanometer sizes can lead to their uneven distribution and defects in the products structure. У роботі розглянуто технологічні особливості одержання литих алюмоматричних композиційних матеріалів (АМК), армованих оксидними та карбідними частинками Al2O3, ZrO2, TiO2, SiC, B4C та WC. Завдяки розвитку методів, таких як лиття з активним перемішуванням, in-situ синтез, перемішування, тертя та ін., можна створювати якісні композити зі сприятливими структурними характеристиками та високим рівнем механічних властивостей. Серед розглянутих методів одержання литих алюмоматричних композитів найбільш застосовуваними є лиття з активним перемішуванням розплаву та лиття під тиском. Перший спосіб універсальний для замішування і розподілення армуючих частинок, а другий дозволяє мінімізувати дефектність і пористість структури. Показано, що висока дисперсність добавок оксидів і карбідів частіше призводить до негативних наслідків — дефектів незасвоєння та агломерації порошків. Крупні частинки армуючих компонентів, у свою чергу, призводять до утворення пор. Краще засвоєння порошкових добавок за рахунок підвищення їх змочуваності забезпечується кількома способами, найефективнішими з яких є їх попередній підігрів, активація поверхні або додавання до алюмінієвого розплаву магнію в кількості до 1 % мас. Більшість досліджень присвячені створенню АМК на основі сплаву А356. Найпопулярнішими добавками при цьому є Al2O3, ZrO2, SiC, B4C та WC. Оптимальний вміст наповнювачів для більшості досліджуваних складів — близько 2–6 % мас. Оптимальний розмір частинок — у межах 5–35 мкм, що виражається в підвищенні твердості композитів. Більший розмір частинок мало впливає на механічні властивості сплавів, а нанометрові розміри можуть призводити до нерівномірного їх розподілу та дефектів будови виробів.This publication has 63 references indexed in Scilit:
- Effect of Al2O3 Particle Size on Mechanical Properties of Ultrasonic-Assisted Stir-Casted Al A356 Matrix CompositesInternational Journal of Metalcasting, 2020
- Enhanced mechanical properties of in situ aluminium matrix composites reinforced by alumina nanoparticlesArchives of Civil and Mechanical Engineering, 2018
- Mechanical performance of particulate-reinforced Al metal-matrix composites (MMCs) and Al metal-matrix nano-composites (MMNCs)Journal of Materials Science, 2017
- Fabrication and Characterization of Hot Rolled and Hot Extruded Boron Carbide (B4C) Reinforced A356 Aluminum Alloy Matrix Composites Produced by Stir Casting MethodTransactions of the Indian Institute of Metals, 2016
- Proper matrix-reinforcement bonding in cast metal matrix composites as a factor of their good qualityArchives of Civil and Mechanical Engineering, 2016
- Metal Matrix Composite Products by Vibration Casting Method2016
- Metal Matrix Composites: Aluminum2012
- Processing and physical properties of Al2O3/aluminum alloy compositesCeramics International, 2009
- Effect of high energy ball milling on displacement reaction and sintering of Al−Mg/SiO2 composite powdersMetals and Materials International, 2006
- Metal Matrix Composites2006