Enhanced Mechanical and Thermal Properties of Modified Oil Palm Fiber-Reinforced Polypropylene Composite via Multi-Objective Optimization of In Situ Silica Sol-Gel Synthesis
Authors:
- Nasrullah Mat RoziNasrullah Mat Rozi
- Hamidah Abdul HamidHHHamidah Abdul Hamid
- Sohrab HossainSohrab Hossain
- Nor Afifah KhalilNor Afifah Khalil
- Ahmad Naim Ahmad YahayaAYAhmad Naim Ahmad Yahaya
- Ahmad Noor Syimir FizalAFAhmad Noor Syimir Fizal
- Mohd Yusoff HarisMHMohd Yusoff Haris
- Norkhairi AhmadNorkhairi Ahmad
- Muzafar ZulkifliMuzafar Zulkifli
Open Access
- 29 September 2021
- Vol. 13 (19) , 3338
Abstract
A multi-objective optimization of in situ sol-gel process was conducted in preparing oil palm fiber-reinforced polypropylene (OPF-PP) composite for an enhancement of mechanical and thermal properties. Tetraethyl orthosilicate (TEOS) and butylamine were used as precursors and catalysts for the sol-gel process. The face-centered central composite design (FCCD) experiments coupled with response surface methodology (RSM) has been utilized to optimize in situ silica sol-gel process. The optimization process showed that the drying time after the in-situ silica sol-gel process was the most influential factor on silica content, while the molar ratio of TEOS to water gave the most significant effect on silica residue. The maximum silica content of 34.1% and the silica residue of 35.9% were achieved under optimum conditions of 21.3 h soaking time, 50 min drying time, pH value of 9.26, and 1:4 molar ratio of TEOS to water. The untreated oil palm fiber (OPF) and silica sol-gel modified OPF (SiO2-OPF) were used as the reinforcing fibers, with PP as a matrix and maleic anhydride grafted polypropylene (MAgPP) as a compatibilizer for the fiber-reinforced PP matrix (SiO2-OPF-PP-MAgPP) composites preparation. The mechanical and thermal properties of OPF-PP, SiO2-OPF-PP, SiO2-OPF-PP-MAgPP composites, and pure PP were determined. It was found that the OPF-S-PP-MAgPP composite had the highest toughness and stiffness with values of tensile strength, Young’s modulus, and elongation at break of 30.9 MPa, 881.8 MPa, and 15.1%, respectively. The thermal properties analyses revealed that the OPF-S-PP-MAgPP exhibited the highest thermally stable inflection point at 477 °C as compared to pure PP and other composites formulations. The finding of the present study showed that the SiO2-OPF had the potential to use as a reinforcing agent to enhance the thermal-mechanical properties of the composites.Keywords
Funding Information
- Universiti Kuala Lumpur Short Term Research Grant (STRG) (STR19036)
This publication has 44 references indexed in Scilit:
- Effects of fiber loading, fiber type, its mesh sizes, and coupling agent on the properties of oil palm biomass/polypropylene compositesJournal of Composite Materials, 2011
- Biodegradable composites based on lignocellulosic fibers—An overviewProgress in Polymer Science, 2009
- Utilization of oil palm as a source of renewable energy in MalaysiaRenewable and Sustainable Energy Reviews, 2008
- Modification of biodegradable polylactide by silica and wood flour through a sol–gel processJournal of Applied Polymer Science, 2008
- Effect of sol–gel derived nano-silica and organic peroxide on the thermal and mechanical properties of low-density polyethylene/wood flour compositesPolymer Degradation and Stability, 2008
- Predicting the tensile strength of natural fibre reinforced thermoplasticsComposites Science and Technology, 2007
- Silicon-29 NMR of Solid Silicates2007
- Chopped glass and recycled newspaper as reinforcement fibers in injection molded poly(lactic acid) (PLA) composites: A comparative studyComposites Science and Technology, 2006
- Effect of epoxy functionalized compatibilizer on the mechanical properties of low‐density polyethylene/plasticized tapioca starch blendsPolymer International, 2001
- Thermal degradation of flax and jute fibersJournal of Applied Polymer Science, 2001