Evaluation of Shear Bond Strength Between Denture Teeth and 3D‐Printed Denture Base Resin
Authors:
- 16 June 2022
- journal article
- research article
- Published by Wiley in Journal of Prosthodontics
- Vol. 32 (S1) , 3-10
Abstract
Purpose: The aim of this study was to evaluate the bond strength between two types of artificial teeth with a 3D‐printed denture base resin using different bonding agents.Materials and methods: Two types of artificial teeth were evaluated: 3D‐printed (Cosmos TEMP) and prefabricated polymethylmethacrylate (Biotone) bonded to cylinders (2.5 mm in height and 5 mm in diameter) of 3D‐printed denture bases (Cosmos Denture designing by Meshmixer and printed by Flashforge Hunter DLP Resin 3D Printer). Two combinations between denture base and artificial teeth were eveluated: Cosmos Denture – Biotone, n = 30, and Cosmos Denture ‐ Cosmos TEMP, n = 30. For each combination, the specimens were randomly distributed according to the bonding agent: (1) autopolymerized acrylic resin‐Duralay, n = 10; (2) 3D‐printed resin Cosmos TEMP, n = 10; and (3) methylmethacrylate monomer (MMA) + 3D‐printed resin Cosmos TEMP, n = 10, totaling 60 specimens. The application of MMA was done conditioning the tooth surface for 180 seconds; the other agents were applied on the same surface. The virtual design of the 3D‐printed resin teeth was obtained by scanning the first maxillary molar of the prefabricated teeth as the same protocol of cylinders. The control group (n = 10) was a conventional heat‐polymerized denture base resin (Lucitone 550) bonded to the prefabricated resin teeth (Biotone). The shear bond tests were performed by applying a perpendicular force to the artificial tooth – denture base resin, through a chisel at 1 mm/min until failure. Two‐way ANOVA and Bonferroni post hoc tests (α = 0.05) were used for multiple comparisons.Results: For the Biotone tooth, the bond strength was significantly higher using MMA + Cosmos TEMP (10.04 MPa), and similar to the control (11.84 MPa, p = 0.484). For the 3D‐printed tooth (Cosmos TEMP), the bond strength using the agents Cosmos TEMP (9.57 MPa) and MMA + Cosmos TEMP (12.72 MPa) were similar to the control (11.84 MPa, p = 0.169 and p = 1, respectively), but different from each other (p = 0.016).Conclusions: From the results, it is recommended to use: MMA + Cosmos TEMP bonding agent for the Biotone tooth; and Cosmos TEMP or MMA + Cosmos TEMP bonding agents for the Cosmos TEMP tooth, both attached to the 3D‐printed denture resin Cosmos Denture.Keywords
This publication has 34 references indexed in Scilit:
- Bonding of acrylic denture teeth to MMA/PMMA and light-curing denture base materials: The role of conditioning liquidsJournal of Dentistry, 2012
- Effect of pre‐processing methods on bond strength between acrylic resin teeth and acrylic denture base resinGerodontology, 2011
- Measurement of Interfacial Porosity at the Acrylic Resin/Denture Tooth InterfaceJournal of Prosthodontics, 2010
- Multiphase Polymeric Materials for Rapid Prototyping and Tooling Technologies and Their ApplicationsComposite Interfaces, 2010
- Effect of monomer treatment and polymerisation methods on the bond strength of resin teeth to denture base materialGerodontology, 2009
- Evaluation of the Bond Strength of Denture Base Resins to Acrylic Resin Teeth: Effect of ThermocyclingJournal of Prosthodontics, 2009
- Bond strength of denture teeth to acrylic resin: effect of thermocycling and polymerisation methodsGerodontology, 2008
- Influence of Microwave Polymerization Method and Thickness on Porosity of Acrylic ResinJournal of Prosthodontics, 2007
- Bonding acrylic teeth to acrylic resin denture bases: a reviewGerodontology, 2006
- The swelling phenomenon of acrylic resin polymer teeth at the interface with denture base polymersThe Journal of Prosthetic Dentistry, 1997