Submicro-pore containing poly(ether sulfones)/polyvinylpyrrolidone membranes for high-temperature fuel cell applications
- 13 March 2015
- journal article
- research article
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 3 (16) , 8847-8854
Abstract
A submicro-pore containing proton exchange membrane (PEM) consisting of poly(ether sulfones) (PES) and polyvinylpyrrolidone (PVP) was successfully prepared through a scalable polymer blending method with monodispersed SiO2 solid spheres as a hard template. After doping with phosphoric acid (PA), an outstanding balance between proton conductivity and mechanical strength in these blends is obtained. The tensile strength of all the porous PES/PVP membranes ranges from 5.98 to 3.69 MPa with an increasing content of SiO2 from 10 wt% to 50 wt%, which satisfies the mechanical requirements of high-temperature proton exchange membrane fuel cells (PEMFCs). A proton conductivity of 0.09 S cm−1 is obtained for the as prepared composite membrane with a PA doping level of 350 wt% at 180 °C under anhydrous conditions, comparable with the state-of-the-art PBI/PA membranes. The mechanism for the “balanced” properties is that after the PA doping treatment, the mechanical strength satisfies the requirements of high-temperature PEMFCs with a decreased content of PVP at 50 wt%, while the proton conductivity is improved under the cooperative proton transfers both along the “bonded acid” caged inside the pores and the PA-rich domain formed by “free acid” in the submicro-pores. Furthermore, the PEM fuel cell with PA doped porous PES/PVP exhibits a power density of 454 mW cm−2 at 180 °C H2/O2 without external humidification. A fuel cell performance of ∼520 mV at 0.2 A cm−2 is maintained for 150 h without obviously decreasing. The submicro-pore containing PES/PVP blends allowed for a higher PA doping level, and consequently, enhanced proton conductivity, as well as improved mechanical strength and cell performance, showing potential for use as an alternative high-temperature PEM for fuel cells under anhydrous conditions.Keywords
This publication has 36 references indexed in Scilit:
- New anhydrous proton exchange membranes for high-temperature fuel cells based on PVDF–PVP blended polymersJournal of Materials Chemistry A, 2014
- Polysulfonated Fluoro‐oxyPBI Membranes for PEMFCs: An Efficient Strategy to Achieve Good Fuel Cell Performances with Low H3PO4 Doping LevelsAdvanced Energy Materials, 2014
- High Molecular Weight Polybenzimidazole Membranes for High Temperature PEMFCFuel Cells, 2013
- High temperature (HT) polymer electrolyte membrane fuel cells (PEMFC) – A reviewJournal of Power Sources, 2013
- Crosslinked Hexafluoropropylidene Polybenzimidazole Membranes with Chloromethyl Polysulfone for Fuel Cell ApplicationsAdvanced Energy Materials, 2013
- Improving the proton conductivity and water uptake of polybenzimidazole-based proton exchange nanocomposite membranes with TiO2 and SiO2 nanoparticles chemically modified surfacesJournal of Power Sources, 2011
- Proton-conducting membranes based on benzimidazole polymers for high-temperature PEM fuel cells. A chemical questChemical Society Reviews, 2010
- Development of high-temperature PEMFC based on heteropolyacids and polybenzimidazoleJournal of Solid State Electrochemistry, 2008
- Phosphoric acid-doped poly(1-vinyl-1,2,4-triazole) as water-free proton conducting polymer electrolytesSolid State Ionics, 2008
- PBI‐Based Polymer Membranes for High Temperature Fuel Cells – Preparation, Characterization and Fuel Cell DemonstrationFuel Cells, 2004