Mechanically Enhanced 3D Printable Photocurable Resin Composed of Epoxy Waste Cooking Oil and Triethylene Glycol Dimethacrylate
Authors:
- Meng-Yu LiuMLMeng-Yu Liu
- Gui-Mei LiGLGui-Mei Li
- Peng-Yu WangPWPeng-Yu Wang
- Wan-Ying YingWYWan-Ying Ying
- Yang YangYYYang Yang
- Chuan-Yang TangCTChuan-Yang Tang
- Ying-Ying LiYLYing-Ying Li
- Shou-Ping ChenSCShou-Ping Chen
Preprint
- 18 March 2024
- preprint
- Published by Springer Nature in Research Square
Abstract
This study introduces an innovative strategy, termed the "epoxidation & combination" approach, to create cost-effective and mechanically enhanced 3D printing photocurable materials by using waste cooking oil (WCO) as raw material. Within this strategy, WCO is first subjected to epoxidation, yielding epoxy waste cooking oil (E-WCO). Subsequently, E-WCO is combined with triethylene glycol dimethacrylate (TEGDMA) to formulate a E-WCO plasticized TEGDMA photocurable resin suitable for 3D printing. Functioning as a plasticizing component, E-WCO effectively resides within the TEGDMA substrate with minimal migration (0.30% at 135℃ for 24 hours). Furthermore, appropriate addition of E-WCO significantly enhances the mechanical properties of the TEGDMA-based resin, especially in terms of toughness. The optimized composition of the E-WCO/TEGDMA 3D printing resin, with an E-WCO : TEGDMA mass ratio of 1:15, demonstrates exceptional mechanical strength. This includes a tensile strength of 16.74 MPa, an elongation at break of 32.93%, and an impact strength of 3.94 kJ/m2, surpassing the benchmarks of pure TEGDMA. When compared to commercial epoxy soybean oil (ESO), E-WCO provides an equivalent plasticizing effect, effectively enhancing material flexibility. The transformation of WCO into the E-WCO/TEGDMA resin not only promotes the high-value utilization of WCO but also holds significant potential for developing low-cost and sustainable 3D printing consumables.Keywords
All Related Versions
- Version 1, 2024-03-18, Research Square
- Published version: Journal of Polymer Research, 31 (6), 1.
This publication has 36 references indexed in Scilit:
- Preparation and UV‐curing properties of rosin‐based allyl phthalate oligomerPolymers for Advanced Technologies, 2023
- Digital Light Processing‐3D Printing of Thermoset Materials with High Biodegradability from Amino Acid‐Derived Acrylamide MonomersMacromolecular Rapid Communications, 2023
- Degree of conversion and residual monomer elution of 3D-printed, milled and self-cured resin-based composite materials for temporary dental crowns and bridgesJournal of Materials Science: Materials in Medicine, 2023
- Digital light processing 3D printing of barium titanate/1,6-ethylene glycol diacrylate/polyethylene glycol (400) diacrylate nanocompositesAdvanced Composites and Hybrid Materials, 2023
- Photocurable Printed Piezocapacitive Pressure Sensor Based on an Acrylic Resin Modified with Polyaniline and LigninAdvanced Materials Technologies, 2022
- From Natural Oils to Epoxy Resins: A New Paradigm in Renewable Performance MaterialsJournal of Polymers and the Environment, 2021
- Photosensitive acrylates containing bio‐based epoxy‐acrylate soybean oil for 3D printing applicationJournal of Applied Polymer Science, 2021
- Indoor use of essential oil-based cleaning products: Emission rate and indoor air quality impact assessment based on a realistic application methodologyAtmospheric Environment, 2021
- Soybean‐Oil‐Based Thermosetting Resins with Methacrylated Vanillyl Alcohol as Bio‐Based, Low‐Viscosity ComonomerMacromolecular Materials and Engineering, 2017
- Green plasticizers derived from soybean oil for poly(vinyl chloride) as a renewable resource materialKorean Journal of Chemical Engineering, 2016