Synthesis of α‐cellulose/polypyrrole composite for the removal of reactive red dye from aqueous solution: Kinetics and equilibrium modeling
- 24 February 2014
- journal article
- research article
- Published by Wiley in Polymer Composites
- Vol. 36 (2) , 312-321
Abstract
In this work, a composite from α‐cellulose coated with conducting polypyrrole by in situ polymerization using potassium persulfate as oxidant was obtained. The composite was characterized by fourier transform infrared (FTIR) spectroscopy, cyclic voltammetry, UV/Vis spectroscopy, and scanning electron microscopy (SEM) analysis showed homogeneous coating of α‐cellulose with polypyrrole (PPy) to produce a composite with a conductivity of 3.5 × 10−5 S/m. Batch aqueous adsorption experiments of the reactive red 120 (RR120) dye onto the synthesized material were conducted. The results showed that this composite is an efficient adsorbent for RR120 dye removal. For the adsorption experiments set to an initial pH of 3.9, the adsorption capacity was 15.6 mg of dye/g of composite for an equilibrium concentration (in the liquid) of RR120 dye equal to 1,000 mg/L, whereas a value of 96.1 mg of dye/g of composite was obtained when the solution pH was set to 2.0 for the same equilibrium concentration. When performing adsorption experiments using pure α‐cellulose, dye adsorption was insignificant at any pH value. Adsorption isotherm for RR120 was described by a typical Freundlich model. The transient adsorption of RR120 on the synthesized composite was described by a general three‐resistance model that includes the transport on the film that surrounds the composite particles, diffusion inside the particles, and adsorption on the surface of the particles. A fitting of the uptake curves was performed allowing the estimation of values for the effective diffusivity, D0, and the adsorption rate coefficient, k1. For the adsorption experiments with an initial pH value set to 3.9, D0 was estimated as 1.05 × 10−10 m2/s, whereas k1 was 1.65 × 10−4 Ln/g mgn − 1 s; the corresponding values of k1 at pH = 2 and 9.0 were 3.18 × 10−4 and 5.16 × 10−5, respectively. POLYM. COMPOS., 36:312–321, 2015. © 2014 Society of Plastics EngineersKeywords
Funding Information
- CONACYT - Mexico (80843)
This publication has 31 references indexed in Scilit:
- Comparison of Jatropha curcas shells in natural form and treated by non-thermal plasma as biosorbents for removal of Reactive Red 120 textile dye from aqueous solutionIndustrial Crops and Products, 2013
- Sorption equilibrium, kinetic, thermodynamic, and desorption studies of Reactive Red 120 on Chara contrariaChemical Engineering Journal, 2012
- Facile Synthesis of Water-Dispersible Conducting Polymer NanospheresACS Nano, 2010
- A Nanocellulose Polypyrrole Composite Based on Microfibrillated Cellulose from WoodThe Journal of Physical Chemistry B, 2010
- Sorption of SPADNS azo dye on polystyrene anion exchangers: Equilibrium and kinetic studiesJournal of Hazardous Materials, 2009
- On the porosity of polypyrrole filmsSynthetic Metals, 2007
- Study of polaron and bipolaron states in polypyrrole by in situ Raman spectroelectrochemistryElectrochimica Acta, 2007
- Sorption isotherms: A review on physical bases, modeling and measurementApplied Geochemistry, 2007
- Conducting Polymers on Paper FibresSynthetic Metals, 2005
- Evaluation of effective diffusion coefficient and intrinsic kinetic parameters on azo dye biodegradation using PVA‐immobilized cell beadsBiotechnology and Bioengineering, 2003