Porous titanium implant materials and their potential in orthopedic surgery
Authors:
- 19 December 2007
- journal article
- research article
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 38 (12) , 1015-1018
Abstract
In orthopedic surgery bony defects remains a challenge. In generally autologous or heterologous bony transplants can be used. Main problem is the limited amount of bone and donor site morbidity. Nowadays excellent implants and scaffolds at low costs are necessary in respect to the financial problems in our health care system and the strong financial limitations in clinical medicine. Recently a biomimetic approach, in which a porous synthetic bone substitute with properties similar to these of trabecular bone has been developed (VITOFOAM™). Aim of our study was to investigate whether cp‐Ti or Ti6Al4V or stainless steel (316L) porous metal implants achieve material properties comparable to bone.Materials and MethodsThree cp‐Ti, Ti6Al4V and stainless steel (316L) porous metal specimen each with a pore size of 150 to 600 μm have been tested in respect to determine the Young’s Modulus E (GPa), Compression Strength (MPa) and Porosity (%) under axial compression.Results Young’s Modulus of the cp‐ Ti samples was in the range of 1.2 to 2.8 GPa, for Ti6Al4V 2.3 to 4.1 GPa could be achieved. Compression Strength for cp‐ Ti and Ti6Al4V ranged from 30 to 65 MPa with porosity values ranged from 71 to 80 %.DiscussionThe highly porous nature of VITOFOAM™ combined with the good biocompatibility of cp‐ Ti or Ti6Al4V and the mechanical properties make these materials ideal bone scaffolds. Trabecular bone shows pore sizes of 300–1500 μm, Young’s Modulus of 0.2–2 GPa and Compression Strength from 5–50 MPa. Porosity of spongious bone ranges from 30 to 95 %. These values are comparable to the values achieved with VITOFOAM™. Porous titanium foam with its osteoconductive properties may therefore be an ideal and cheap alternative. Implant costs can be lowered to 50 % for implants e.g. for intercorporal interbody fusion in spinal surgery. Actually further research is done to show the possibility in spinal surgery or loading technologies with Tricalciumphosphat, Hydroxylapatit, Antibiotics or Cytostatics.Keywords
This publication has 15 references indexed in Scilit:
- Porous Tantalum Patellar AugmentationClinical Orthopaedics and Related Research, 2006
- The Use of a Trabecular Metal Acetabular Component and Trabecular Metal Augment for Severe Acetabular DefectsThe Journal of Arthroplasty, 2006
- Mineralization of hydroxyapatite in electrospun nanofibrous poly(L‐lactic acid) scaffoldsJournal of Biomedical Materials Research Part A, 2006
- Radiological evaluation of the metal-bone interface of a porous tantalum monoblock acetabular componentThe Journal of Bone and Joint Surgery. British volume, 2006
- Particle migration and gap healing around trabecular metal implantsInternational Orthopaedics, 2005
- Engineering craniofacial scaffoldsOrthodontics & Craniofacial Research, 2005
- Factors having influence on the rheological properties of Ti6A14V slurryJournal of Materials Science: Materials in Medicine, 2004
- Influence of the in vitro culture period on the in vivo performance of cell/titanium bone tissue‐engineered constructs using a rat cranial critical size defect modelJournal of Biomedical Materials Research Part A, 2003
- Preparation, degradation, and calcification of biodegradable polyurethane foams for bone graft substitutesJournal of Biomedical Materials Research Part A, 2003
- Tissue Engineered Bone Formation Using Chitosan/Tricalcium Phosphate SpongesJournal of Periodontology, 2000