Hydrofluoric Acid Etched Stainless Steel Wire for Solid-Phase Microextraction
Authors:
- 15 May 2009
- journal article
- research article
- Published by American Chemical Society (ACS) in Analytical Chemistry
- Vol. 81 (12) , 4971-4977
Abstract
Stainless steel wire has been widely used as the substrate of solid-phase microextraction (SPME) fibers to overcome the shortcomings of conventional silica fibers such as fragility, by many researchers. However, in previous reports various sorbent coatings are always required in conjunction with the stainless steel wire for SPME. In this work, we report the bare stainless steel wire for SPME without the need for any additional coatings taking advantage of its high mechanical and thermal stability. To evaluate the performance of stainless steel wire for SPME, polycyclic aromatic hydrocarbons (PAHs), benzene, toluene, ethylbenzene, chlorobenzene, n-propylbenzene, aniline, phenol, n-hexane, n-octane, n-decane, n-undecane, n-dodecane, chloroform, trichloroethylene, n-octanol, and butanol were tested as analytes. Although the stainless steel wire had almost no extraction capability toward the tested analytes before etching, it did exhibit high affinity to the tested PAHs after etching with hydrofluoric acid. The etched stainless steel wire gave a much bigger enhancement factor (2541−3981) for the PAHs than the other analytes studied (≤515). Etching with hydrofluoric acid produced a porous and flower-like structure with Fe2O3, FeF3, Cr2O3, and CrF2 on the surface of the stainless steel wire, giving high affinity to the PAHs due to cation−π interaction. On the basis of the high selectivity of the etched stainless steel wire for PAHs, a new SPME method was developed for gas chromatography with flame ionization detection to determine PAHs with the detection limits of 0.24−0.63 μg L−1. The precision for six replicate extractions using one SPME fiber ranged from 2.9% to 5.3%. The fiber-to-fiber reproducibility for three parallel prepared fibers was 4.3−8.8%. One etched stainless steel wire can stand over 250 cycles of SPME without significant loss of extraction efficiency. The developed etched stainless steel wire is very stable, highly selective, and reproducible for the SPME of PAHs.Keywords
This publication has 56 references indexed in Scilit:
- Application of robust NiTi–ZrO2–PEG SPME fiber in the determination of haloanisoles in cork stopper samplesAnalytica Chimica Acta, 2008
- In situ fabrication of nanostructured titania coating on the surface of titanium wire: A new approach for preparation of solid-phase microextraction fiberAnalytica Chimica Acta, 2008
- Application of NiTi alloy coated with ZrO2 as a new fiber for solid-phase microextraction for determination of halophenols in water samplesAnalytica Chimica Acta, 2007
- Silicone glue coated stainless steel wire for solid phase microextractionAnalytica Chimica Acta, 2006
- An electropolymerized aniline-based fiber coating for solid phase microextraction of phenols from waterAnalytica Chimica Acta, 2005
- Determination of polycyclic aromatic hydrocarbons in water by solid-phase microextraction–gas chromatography–mass spectrometryAnalytica Chimica Acta, 2004
- Solid-Phase Microextraction Coupled to Gas Chromatography/Mass Spectrometry for Determining Polycyclic Aromatic Hydrocarbon−Micelle Partition CoefficientsAnalytical Chemistry, 2004
- Solid-phase microextraction and liquid chromatography/mass spectrometry in drug analysisAnalytica Chimica Acta, 2003
- Detection of chlorinated aromatic amines in aqueous solutions based on an infrared hollow waveguide samplerAnalytica Chimica Acta, 2001
- The Anti-estrogenic Activity of Selected Polynuclear Aromatic Hydrocarbons in Yeast Expressing Human Estrogen ReceptorBiochemical and Biophysical Research Communications, 1996