A Novel Strategy for Desalinating Highly Concentrated Seawater Employs Dilute Regeneration Solutions within a Membrane Capacitive Deionization System, Integrating Nanopatterned Membranes and Prussian Blue Analog-Infiltrated Electrodes
While Earth’s oceans contain about 97% of its water, their high salinity makes them unsuitable for human consumption [1]. In regions where freshwater is limited or unpredictable, seawater desalination can provide a substantial and dependable supply. Existing desalination technologies – reverse osmosis, thermal distillation, and electrodialysis – are effective but energy-intensive, relying on high pressure, thermal input, or electricity. Membrane capacitive deionization (MCDI) is a promising alternative due to its cost-effectiveness, energy efficiency, and environmentally friendly operation. MCDI uses electrochemical adsorption and desorption of salt ions for separation. It is modular, electrified, and does not require high-pressure piping or generate significant acoustic, thermal, or electromagnetic signatures. Flow-by MCDI, a commercialized design, removes ions using electrical energy and consists of two porous electrodes covered by ion-exchange membranes [2]. However, the salt adsorption capacity of carbon electrodes is limited to ~40 mg/g, making them ineffective for seawater desalination [3]. Achieving full electrode regeneration is essential to maximize salt removal. This work introduces an operational strategy using dilute NaCl regeneration solutions (0–5 g/L) to treat 35 g/L NaCl and a mixture of 30 g/L NaCl with 5 g/L MgSO₄. Additionally, surface patterning is explored as a method to enhance membrane performance by increasing the interfacial area and salt flux [4]. Patterned membranes have been shown to improve local hydrodynamics, enhance concentration polarization via secondary flows, and reduce boundary layer thickness and osmotic pressure. Poly(phenylene) alkylene ion-exchange membranes were fabricated with nanopatterns—hexagonal, double ring, octagonal, and rectangular—ranging from 100 to 300 nm using electron beam lithography. Silicon wafers were spin-coated with Zep 520A121 resist and anisole (1:1), baked at 180°C, and exposed using a RAITH EBPG 5200 system (150 nA, 600 µm aperture, 180 µC/cm²). Patterns were developed in n-Amyl acetate and 2-propanol, then dried. PDMS molds were formed by mixing Sylgard 184 elastomer and curing agent (10:1), degassing, pouring onto the patterned wafer, and curing at 65°C for 4 hours. Ionomers were drop-cast onto the molds. To further enhance performance, Prussian blue analogues (PBAs)—redox-active materials with open framework structures—were used as electrode modifiers to improve salt adsorption and charge redistribution [5][6]. A nickel PBA (NaNi[Fe(CN)₆]·nH₂O) was mixed with PVDF and conductive carbon (8:1:1) in N-methyl-2-pyrrolidone and coated on activated carbon cloth electrodes. Initial results show strong deionization across regeneration concentrations (0–5000 ppm NaCl), with minor ion accumulation at 5000 ppm. Compared to flat membranes, hexagonal nanopatterned membranes showed the greatest surface area enhancement, a ~500 mV reduction in cell voltage during chronopotentiometry, a 45 Ω·cm² decrease in area-specific resistance, and an 18.71 Ω·cm² reduction in capacitance during impedance spectroscopy. These findings show that combining dilute regeneration strategies, nanopatterned membranes, and PBA-modified electrodes enables MCDI to effectively manage higher salinity feeds, expanding its potential for seawater desalination. References Saline water and salinity. (n.d.). USGS. Retrieved March 25, 2025, from https://www.usgs.gov/special-topics/water-science-school/science/saline-water-and-salini Palakkal, V. M., Rubio, J. E., Lin, Y. J., & Arges, C. G. (2018). Low-resistant ion-exchange membranes for energy efficient membrane capacitive deionization. ACS Sustainable Chemistry & Engineering , 6 (11), 13778-13786. Tang, K., Kim, Y. H., Chang, J., Mayes, R. T., Gabitto, J., Yiacoumi, S., & Tsouris, C. (2019). Seawater desalination by over-potential membrane capacitive deionization: Opportunities and hurdles. Chemical engineering journal , 357 , 103-111. Hasan, M., Shrimant, B., Waters, C. B., Gorski, C. A., & Arges, C. G. (2024). Reducing Ohmic Resistances in Membrane Capacitive Deionization Using Micropatterned Ion‐Exchange Membranes, Ionomer Infiltrated Electrodes, and Ionomer‐Coated Nylon Meshes. Small Structures , 5 (9), 2400090. Zhang, X., & Dutta, J. (2021). X-Fe (X= Mn, Co, Cu) Prussian blue analogue-modified carbon cloth electrodes for capacitive deionization. ACS Applied Energy Materials , 4 (8), 8275-8284. Pothanamkandathil, V., Boualavong, J., & Gorski, C. A. (2023). Open-circuit potential drift in intercalation electrodes: role of charge redistribution in a prussian blue analog. Journal of The Electrochemical Society , 170 (11), 110503. Figure 1