Optimizing Photo-Encapsulation Viability of Heart Valve Cell Types in 3D Printable Composite Hydrogels
- 22 April 2016
- journal article
- research article
- Published by Springer Nature in Annals of Biomedical Engineering
- Vol. 45 (2) , 360-377
Abstract
Photocrosslinking hydrogel technologies are attractive for the biofabrication of cardiovascular soft tissues, but 3D printing success is dependent on multiple variables. In this study we systematically test variables associated with photocrosslinking hydrogels (photoinitiator type, photoinitiator concentration, and light intensity) for their effects on encapsulated cells in an extrusion 3D printable mixture of methacrylated gelatin/poly-ethylene glycol diacrylate/alginate (MEGEL/PEGDA3350/alginate). The fabrication conditions that produced desired hydrogel mechanical properties were compared against those that optimize aortic valve or mesenchymal stem cell viability. In the 3D hydrogel culture environment and fabrication setting studied, Irgacure can increase hydrogel stiffness with a lower proportional decrease in encapsulated cell viability compared to VA086. Human adipose derived mesenchymal stem cells (HADMSC) survived increasing photoinitiator concentrations in photo-encapsulation conditions better than aortic valve interstitial cells (HAVIC) and aortic valve sinus smooth muscle cells (HASSMC). Within the range of photo-encapsulation fabrication conditions tested with MEGEL/PEGDA/alginate (0.25–1.0% w/v VA086, 0.025–0.1% w/v Irgacure 2959, and 365 nm light intensity 2–136 mW/cm2), the highest viabilities achieved were 95, 93, and 93% live for HASSMC, HAVIC, and HADMSC respectively. These results identify parameter combinations that optimize cell viability during 3D printing for multiple cell types. These results also indicate that general oxidative stress is higher in photocrosslinking conditions that induce lower cell viability. However, suppressing this increase in intracellular oxidative stress did not improve cell viability, which suggests that other stress mechanisms also contribute.Keywords
Funding Information
- National Science Foundation (Graduate Research Fellowship, CBET-0955172)
- American Heart Association (AH0830384N, 13POST17220071)
- Morgan Family Foundation (Morgan Fellowship)
- Felton Family Endowment for Human Heart Valve Research at Seattle Children’s Hospital
- Hartwell Foundation
This publication has 51 references indexed in Scilit:
- Breaking the chain at the membrane: paraoxonase 2 counteracts lipid peroxidation at the plasma membraneThe FASEB Journal, 2014
- Visible light cured thiol-vinyl hydrogels with tunable degradation for 3D cell cultureActa Biomaterialia, 2014
- Horseradish peroxidase/catalase-mediated cell-laden alginate-based hydrogel tube production in two-phase coaxial flow of aqueous solutions for filament-like tissues fabricationBiofabrication, 2013
- Melatonin protects rat thymus against oxidative stress caused by exposure to microwaves and modulates proliferation/apoptosis of thymocytesGeneral Physiology and Biophysics, 2013
- Rapid 3D printing of anatomically accurate and mechanically heterogeneous aortic valve hydrogel scaffoldsBiofabrication, 2012
- Stiffness of photocrosslinked RGD‐alginate gels regulates adipose progenitor cell behaviorBiotechnology and Bioengineering, 2011
- Photocrosslinking of Gelatin Macromers to Synthesize Porous Hydrogels That Promote Valvular Interstitial Cell FunctionTissue Engineering Part A, 2009
- Impact of lactic acid on cell proliferation and free radical‐induced cell death in monolayer cultures of neural precursor cellsBiotechnology and Bioengineering, 2009
- 1-Cys peroxiredoxin overexpression protects cells against phospholipid peroxidation-mediated membrane damageProceedings of the National Academy of Sciences, 2002
- Oxidative damage of vascular smooth muscle cells by the glycated protein–cupric ion systemAtherosclerosis, 1998