Study on the detonation wave propagation of shaped charge with three-layer liner and its driving characteristics to liner
Authors:
Open Access
- 16 April 2024
- journal article
- research article
- Published by Springer Nature in Scientific Reports
- Vol. 14 (1) , 1-13
Abstract
With the continuous improvement of various armor protection technologies, the armor protection performance has increased significantly, and then the damage performance requirements of armor-piercing ammunition have also increased. In order to improve the penetration ability of the liner, a new three-layer liner structure is designed in this paper. The jet forming process was simulated by AUTODYN software. The mechanism of shaped jet forming of three-layer liner was studied. The reason why the penetration depth of three-layer liner was higher than that of ordinary liner was explained. The influence of three-layer liner on the propagation of detonation wave and the change of pressure when detonation wave acted on liner were found, which provided a new idea for improving the penetration depth of jet. The influence of liner material, cone angle and stand-off on jet forming and penetration was also studied by orthogonal optimization experiment, and the structural parameters with the best penetration performance were obtained. The results show that the pressure at the convergence point increases first and then decreases during the formation of the jet of the three-layer liner. The pressure at the convergence point when the three-layer liner material is from low impedance to high impedance from the outside to the inside is much larger than the pressure at the convergence point from high impedance to low impedance. When the three-layer liner material is Al 2024-Copper–Tantalum from the outside to the inside, the pressure at the convergence point of the three-layer liner at different times is higher than that of the double-layer liner and the single-layer liner. Reasonable matching of different impact impedance materials in the three-layer liner can greatly improve the pressure value of the detonation wave acting on the cone liner. The maximum pressure at the convergence point on the axis is 39.10 GPa, which is 22.00% higher than that of the double-layer liner at the convergence point, and 53.03% higher than that of the single-layer liner at the convergence point. The orthogonal design test scheme is simulated and analyzed. The penetration depth is taken as the observation index, and the range analysis is adopted. The results show that the material matching of the three-layer liner has the greatest influence on the depth of the jet penetrating the target plate, followed by the cone angle of the three-layer liner. Relatively speaking, the stand-off has the least influence on the result. Reasonable matching of materials with different impact impedances in the three-layer liner can maximize the penetration depth of the jet into the target plate.Keywords
Funding Information
- Graduate Innovation Project of Shanxi Province under Grant (No.2022Y576)
- the Foundation Research Project of Shanxi Province under Grant (No.2021690)
This publication has 13 references indexed in Scilit:
- The effect of three-layer liner on the jet formation and penetration capability of shaped charge jetScientific Reports, 2023
- The Influence of Closed-Cell W-Shaped Liner Parameters on the Penetration Performance of Integral Annular Shaped ChargeMaterials, 2022
- The Effect of Cylindrical Liner Material on the Jet Formation and Penetration Capability of Cylinder-Cone-Shaped ChargeMaterials, 2022
- Experimental and numerical study on jet properties and penetration of double-layered shaped chargeJournal of Mechanical Science and Technology, 2020
- The EFP Formation and Penetration Capability of Double-Layer Shaped Charge with Wave ShaperMaterials, 2020
- Numerical simulation of the formation of shaped-charge jets from hemispherical liners of degressive thicknessCombustion, Explosion, and Shock Waves, 2016
- A Model for Explosive Reactive Armor Interaction with Shaped Charge JetPropellants, Explosives, Pyrotechnics, 2015
- Investigation of a Nickel-Aluminum Reactive Shaped Charge LinerJournal of Applied Mechanics, 2013
- Ballistic performance of multi-layered metallic plates impacted by a 7.62-mm APM2 projectileInternational Journal of Impact Engineering, 2011
- Studies on jet formation and penetration for a double-layer shaped chargeCombustion, Explosion, and Shock Waves, 2011