Dual nanofiber and graphene reinforcement of 3D printed biomimetic supports for bone tissue repair
Authors:
- Elena CojocaruECElena Cojocaru
- Mădălina OpreaMOMădălina Oprea
- George Mihail VlăsceanuGVGeorge Mihail Vlăsceanu
- Mădălina-Cristina NicolaeMNMădălina-Cristina Nicolae
- Roxana-Cristina PopescuRPRoxana-Cristina Popescu
- Paul-Emil MereuţăPMPaul-Emil Mereuţă
- Alin-Georgian ToaderATAlin-Georgian Toader
- Mariana IoniţăMariana Ioniţă
Open Access
- 9 October 2024
- journal article
- research article
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 14 (44) , 32517-32532
Abstract
Replicating the intricate architecture of the extracellular matrix (ECM) is an actual challenge in the field of bone tissue engineering. In the present research study, calcium alginate/cellulose nanofibrils-based 3D printed scaffolds, double-reinforced with chitosan/polyethylene oxide electrospun nanofibers (NFs) and graphene oxide (GO) were prepared using the 3D printing technique. The porous matrix was provided by the calcium alginate, while the anisotropy degree and mechanical properties were ensured by the addition of fillers with different sizes and shapes (CNFs, NFs, GO), similar to the components naturally found in bone ECM. Surface morphology and 3D internal microstructure were analyzed using scanning electron microscopy (SEM) and micro-computed tomography (μ-CT), which evidenced a synergistic effect of the reinforcing and functional fibers addition, as well as of the GO sheets that seem to govern materials structuration. Also, the nanoindentation measurements showed significant differences in the elasticity and viscosity modulus, depending on the measurement point, this supported the anisotropic character of the scaffolds. In vitro assays performed on MG-63 osteoblast cells confirmed the biocompatibility of the calcium alginate-based scaffolds and highlighted the osteostimulatory and mineralization enhancement effect of GO. In virtue of their biocompatibility, structural complexity similar with the one of native bone ECM, and biomimetic mechanical characteristics (e.g. high mechanical strength, durotaxis), these novel materials were considered appropriate for specific functional needs, like guided support for bone tissue formation.Keywords
Funding Information
- Ministerul Cercetării, Inovării şi Digitalizării (PCE 103/2022)
- Ministerul Cercetării, Inovării şi Digitalizării (PNRR 213/29.11.2022)
- European Commission (760093/23.05.2023)
This publication has 64 references indexed in Scilit:
- Bone tissue engineering: Anionic polysaccharides as promising scaffoldsCarbohydrate Polymers, 2022
- 3D printed alginate-cellulose nanofibers based patches for local curcumin administrationCarbohydrate Polymers, 2021
- Multiphase calcium alginate membrane composited with cellulose nanofibers for selective mass transferSN Applied Sciences, 2020
- Applications of chitin and chitosan nanofibers in bone regenerative engineeringCarbohydrate Polymers, 2020
- Preparation, characterization and dielectric properties of sodium alginate/titanium dioxide composite membranesSN Applied Sciences, 2018
- Co-deteriorations of anisotropic extracellular matrix arrangement and intrinsic mechanical property in c-src deficient osteopetrotic mouse femurBone, 2017
- Synthetic hydrogels with stiffness gradients for durotaxis study and tissue engineering scaffoldsTissue Engineering and Regenerative Medicine, 2016
- Sodium alginate/graphene oxide composite films with enhanced thermal and mechanical propertiesCarbohydrate Polymers, 2013
- The effect of 3D hydrogel scaffold modulus on osteoblast differentiation and mineralization revealed by combinatorial screeningBiomaterials, 2010
- Skeletal physiology: responses to exercise and training1962