Comparison of thin‐layer and bulk MIPs synthesized by photoinitiated in situ crosslinking polymerization from the same reaction mixtures
- 21 July 2005
- journal article
- research article
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 98 (1) , 362-372
Abstract
The synthesis and comparative characterization of molecularly imprinted polymers (MIPs) in two different formats, as thin layers grafted to the entire surface of polypropylene microfiltration membranes and as conventional particles, are described. Imprinting with atrazine was performed by using itaconic acid and N,N′‐methylene‐bisacrylamide as functional and crosslinker monomers in methanol as the solvent. Polymerization had been initiated by UV irradiation of benzoin ethyl ether and driven to low monomer conversion for the thin‐layer polymers and to high monomer conversion for the bulk materials. The binding performance of MIP composite membranes and of MIP particles packed into cartridges was evaluated in solid‐phase extraction (SPE) experiments of atrazin and simazin from aqueous solutions. The SPE performance depended strongly on pH and buffer concentration. Although an imprinting effect was observed for both formats, the specificity (MIP versus Blank) and the selectivity (atrazin versus simazin) were much higher for the thin‐layer composite membranes than for the bulk polymer particles. In particular, the atrazin/simazin selectivity increased from 32% for the Blank to 78% for the MIP composite membranes. A major reason is the hindered accessibility of the internal pore structure of the particles, whereas the porous filtration membranes are much more compatible with the fast SPE protocol. Furthermore, based on pKa of the functional carboxylic acid groups—from potentiometric titration and polarity of the binding environment—from fluorescent probe analysis, different properties of the imprinted binding sites can be postulated for the two MIP formats. However, the differences between MIP and Blank were much more pronounced for the thin‐layer composite membranes. The hydrophobic surface of the polypropylene membrane appeared to be a major factor affecting the binding performance of thin‐layer MIPs. The new porous composite membranes could be particularly useful as selective SPE materials in environmental, pharmaceutical, and analytical applications. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 362–372, 2005Keywords
This publication has 20 references indexed in Scilit:
- Molecularly Imprinted Polymers via High‐Throughput and Combinatorial TechniquesMacromolecular Rapid Communications, 2003
- Selective Picomolar Detection of Hexachlorobenzene in Water Using a Quartz Crystal Microbalance Coated with a Molecularly Imprinted Polymer Thin FilmLangmuir, 2003
- Polymer Cookery: Influence of Polymerization Conditions on the Performance of Molecularly Imprinted PolymersMacromolecules, 2002
- Molecular Imprinting for the Recognition of N-Terminal Histidine Peptides in Aqueous SolutionMacromolecules, 2002
- Thin layer molecularly imprinted microfiltration membranes by photofunctionalization using a coated α-cleavage photoinitiatorThe Analyst, 2001
- Surface Functionalization of Porous Polypropylene Membranes with Molecularly Imprinted Polymers by Photograft Copolymerization in WaterMacromolecules, 2000
- Selective recognition of atrazine by molecularly imprinted polymer membranes. Development of conductometric sensor for herbicides detectionAnalytica Chimica Acta, 1999
- Molecular Imprinting in Cross‐Linked Materials with the Aid of Molecular Templates— A Way towards Artificial AntibodiesAngewandte Chemie International Edition, 1995
- The use of acidic and basic excipients in the release of 5-fluorouracil and mitomycin C from a semi-solid bioerodible poly(ortho ester)Journal of Controlled Release, 1995
- Hexazinone Adsorption‐Desorption Studies with Soil and Organic AdsorbentsJournal of Environmental Quality, 1985