Biomechanical Comparison of C1–C2 Posterior Arthrodesis Techniques
Authors:
- Bradford L. CurrierBCBradford L. Currier
- Yukitaka HokariYHYukitaka Hokari
- Patricia G. NealePNPatricia G. Neale
- Chunfeng ZhaoCZChunfeng Zhao
- Lawrence J. BerglundLBLawrence J. Berglund
- Dirk R. LarsonDLDirk R. Larson
- Kai-Nan AnKAKai-Nan An
- 1 June 2007
- journal article
- research article
- Published by Wolters Kluwer Health in Spine
- Vol. 32 (13) , E363-E370
Abstract
Biomechanical comparison of 5 atlantoaxial posterior arthrodesis techniques. To assess the relative value of different posterior wire constructs when one or two transarticular screws are used. A combination of Gallie or Brooks techniques and 2 posterior transarticular screws has been shown to be effective for atlantoaxial arthrodesis. Anatomic constraints may preclude the insertion of a transarticular screw unilaterally or bilaterally. Ten adult human cadaveric upper cervical spine specimens were used. The specimens were tested intact, after odontoidectomy and transverse and capsular ligament section and after stabilization with each of the 5 techniques: Brooks-Jenkins cable fixation, Brooks-Jenkins with unilateral transarticular screw, Gallie posterior wire construct with unilateral transarticular screw, Brooks-Jenkins with bilateral screws, and Gallie with bilateral screws. Pure moments were applied in flexion-extension, lateral bending, and torsion within physiologic limits (<1.5 Nm). In flexion-extension and lateral bending, the range of motion (ROM) and neutral zone (NZ) increased significantly after the specimens were injured as compared with intact spines (P < 0.001). After stabilization, the ROM and NZ were significantly lower than in injured and intact spines in all motions (P < 0.01) except lateral bending in the intact spine. Among the 5 instrumented techniques, the ROM for the Gallie construct with 1 screw was significantly higher than for the Brooks-Jenkins construct with 1 or 2 screws in flexion-extension (P < 0.05). In axial torsion, the Gallie construct with 1 screw displayed a larger NZ and ROM than any of the other 4 constructs (P < 0.05). Gallie or Brooks-Jenkins cable fixation alone may not be adequate for atlantoaxial arthrodesis. If 2 supplemented transarticular screws can beinserted, there is no difference between the Gallie or Brooks techniques. If only a single screw can be inserted, the Brooks-Jenkins technique is recommended rather than a Gallie technique.Keywords
This publication has 38 references indexed in Scilit:
- Biomechanical characteristics of C1–2 cable fixationsJournal of Neurosurgery, 1996
- Plate and screw fixation for atlanto-axial subluxationActa Neurochirurgica, 1994
- Three-Dimensional Movements of the Upper Cervical SpineSpine, 1988
- Use of Halifax Interlaminar Clamps for Posterior C1-C2 ArthrodesisNeurosurgery, 1988
- Posterior Stabilization with an Interlaminar Clamp in Cervical Injuries: Technical Note and Review of the Long Term Experience with the MethodNeurosurgery, 1984
- Modified Brooks Fusion for an Os Odontoideum Associated with an Incomplete Posterior Arch of the AtlasSpine, 1983
- Posterior Fusions of the Cervical SpineNeurosurgery, 1981
- ATLANTO-AXIAL FRACTURE-DISLOCATIONSThe Journal of Bone and Joint Surgery. British volume, 1973
- Direct Anterior Approach to the Upper Cervical SpineJournal of Bone and Joint Surgery, 1962
- Fractures and dislocations of the cervical spineThe American Journal of Surgery, 1939