The size effect on intermetallic microstructure evolution of critical solder joints for flip chip assemblies
Authors:
- Justin ChowJCJustin Chow
- Xi LiuXLXi Liu
- Suresh K. SitaramanSSSuresh K. Sitaraman
- 7 September 2015
- journal article
- research article
- Published by Emerald Publishing in Soldering & Surface Mount Technology
- Vol. 27 (4) , 178-184
Abstract
Purpose: – The purpose of this paper is to study the intermetallic compound (IMC) thickness, composition and morphology in 100-μm pitch and 200-μm pitch Sn–Ag–Cu (SAC305) flip-chip assemblies after bump reflow and assembly reflow. In particular, emphasis is placed on the effect of solder joint size on the interfacial IMCs between metal pads and solder matrix. Design/methodology/approach: – This work uses 100-μm pitch and 200-μm pitch silicon flip chips with nickel (Ni) pads and stand-off height of approximately 45 and 90 μm, respectively, assembled on substrates with copper (Cu) pads. The IMCs evolution in solder joints was investigated during reflow by using 100- and 200-μm pitch flip-chip assemblies. Findings: – After bump reflow, the joints size controls the IMC composition and dominant IMC type as well as IMC thickness and also influences the dominant IMC morphology. After assembly reflow, the cross-reaction of the pad metallurgies promotes the dominant IMC transformation and shape coarsened on the Ni pad interface for smaller joints and promotes a great number of new dominate IMC growth on the Ni pad interface in larger joints. On the Cu pad interface, many small voids formed in the IMC in larger joints, but were not observed in smaller joints, combined with the drawing of the IMC growth process. Originality/value: – With continued advances in microelectronics, it is anticipated that next-generation microelectronic assemblies will require a reduction of the flip-chip solder bump pitch to 100 μm or less from the current industrial practice of 130 to150 μm. This work shows that as the packaging size reduced with the solder joint interconnection, the solder size becomes an important factor in the intermetallic composition as well as morphology and thickness after reflow.Keywords
This publication has 24 references indexed in Scilit:
- Characterization of IMC layer and its effect on thermomechanical fatigue life of Sn–3.8Ag–0.7Cu solder jointsJournal of Alloys and Compounds, 2012
- Effects of solder dimension on the interfacial shear strength and fracture behaviors of Cu/Sn–3Cu/Cu jointsScripta Materialia, 2012
- A review on thermal cycling and drop impact reliability of SAC solder joint in portable electronic productsMicroelectronics Reliability, 2012
- Effects of bump size on deformation and fracture behavior of Sn3.0Ag0.5Cu/Cu solder joints during shear testingMaterials Science and Engineering: A, 2011
- Cu6Sn5 Morphology Transition and Its Effect on Mechanical Properties of Eutectic Sn-Ag Solder JointsJournal of Electronic Materials, 2010
- Modeling the diffusion of solid copper into liquid solder alloysThin Solid Films, 2008
- The influence of solder volume and pad area on Sn–3.8Ag–0.7Cu and Ni UBM reaction in reflow soldering and isothermal agingMicroelectronics Reliability, 2008
- Experimental characterization and mechanical behavior analysis of intermetallic compounds of Sn–3.5Ag lead-free solder bump with Ti/Cu/Ni UBM on copper chipMicroelectronics Reliability, 2006
- Influence of interfacial intermetallic compound on fracture behavior of solder jointsMaterials Science and Engineering: A, 2003
- Six cases of reliability study of Pb-free solder joints in electronic packaging technologyMaterials Science and Engineering: R: Reports, 2002