Biaxial Shear Crack Propagation Modes of Rock‐Like Specimens with Prefabricated Fissures and Their Strength Characteristics
Open Access
- 1 January 2021
- journal article
- research article
- Published by Wiley in Shock and Vibration
- Vol. 2021 (1)
Abstract
A biaxial shear test is performed on prefabricated, single‐fissure type, cubic rock‐like specimens by using the TZW‐500 rock direct shear apparatus to study the shear strength characteristics, crack coalescence, and propagation modes of the specimens with different geometric parameters. Results show that the crack coalescence and propagation modes of the rock‐like specimens with prefabricated fissures can be divided into four types, namely, single main shear crack coalescence mode, main shear crack coalescence and secondary tensile‐shear crack propagation mode, main shear crack coalescence and secondary shear crack propagation mode, and main shear crack coalescence and secondary tensile crack propagation mode. All modes are affected by the dip angle α and length l of the prefabricated fissure. When the dip angle of the prefabricated fissure is α∈[0°, 20°) or (70°, 90°], the cracks center on shear failure, and most shear cracks propagate along one end of the prefabricated fissure. At α∈(30°, 50°), the cracks bear the tensile‐shear combined action, and the shear cracks propagate along the two ends of the prefabricated fissure. The peak shear strength of the rock‐like specimens with prefabricated fissures is also closely related to the dip angle α and length l of the fissure. With the increase in dip angle α of the prefabricated fissure, the peak shear strength of each rock‐like specimen decreases initially then increases, and the peak shear strength curve presents a similar “U” shape. At α∈[30°, 60°], the peak shear strength is within the peak‐valley interval. When the length l of the prefabricated fissure is increased, the peak shear strength experiences a gradual reduction. When l > 20 mm, the peak shear strength is greatly influenced by l, but the influence is minimal when l ≥ 20 mm. At the same dip angle α and fissure length of l ≥ 20 mm, the correlation between peak shear strength and fissure width b is low.Keywords
Funding Information
- Anhui Natural Science Research Program of Universities and Colleges (KJ2018A0073, anhui-0004-2017AQ)
- Science and Technology Program of Key Major Safety Production Accident Prevention and Control Technology (KJ2018A0073, anhui-0004-2017AQ)
This publication has 16 references indexed in Scilit:
- Crack Initiation, Propagation and Coalescence in Rock-Like Material Containing Two Flaws: a Numerical Study Based on Bonded-Particle Model ApproachRock Mechanics and Rock Engineering, 2012
- Crack coalescence behavior of brittle sandstone samples containing two coplanar fissures in the process of deformation failureEngineering Fracture Mechanics, 2011
- Crack initiation, propagation and coalescence from frictional flaws in uniaxial compressionEngineering Fracture Mechanics, 2010
- Experimental research on pre-cracked marble under compressionInternational Journal of Solids and Structures, 2005
- Coalescence of multiple flaws in a rock-model material in uniaxial compressionInternational Journal of Rock Mechanics and Mining Sciences, 2002
- Crack propagation and coalescence in brittle materials under compressionEngineering Fracture Mechanics, 1998
- Crack coalescence in a rock-like material containing two cracksInternational Journal of Rock Mechanics and Mining Sciences, 1998
- Numerical simulation of progressive rock failure and associated seismicityInternational Journal of Rock Mechanics and Mining Sciences, 1997
- The failure of brittle porous solids under compressive stress statesActa Metallurgica, 1986
- The failure of brittle solids containing small cracks under compressive stress statesActa Metallurgica, 1986