Evaluation of the failure modes and load-bearing capacity of different surface-treated polyether ether ketone copings veneered with lithium di-silicate compared to polyether ether ketone copings veneered with composite: An in vitro study
- 1 January 2021
- journal article
- research article
- Published by Medknow in The Journal of Indian Prosthodontic Society
- Vol. 21 (3) , 295-303
Abstract
Aims: The purpose of this study is to compare and evaluate the failure modes and load-bearing capacity of different surface-treated polyether ether ketone (PEEK) copings when veneered with lithium di-silicate with that of PEEK veneered with composite. Settings and Design: In vitro; comparative study. Materials and Methods: Congruently anatomically shaped single unit PEEK copings (n = 40) were fabricated by scanning a prepared typodont tooth. The PEEK copings were subdivided among four groups (n = 10/group). Among all, one group of PEEK coping was veneered with Urethane dimethacrylate (UDMA)-based composite and other groups were veneered with lithium-di-silicate after different surface treatment on peek copings, i.e., (i) composite veneered PEEK fixed dental prosthesis (FDP) (control group: Group PC), (ii) lithium di-silicate veneered PEEK FDP (no surface treatment: Group PCeN), (iii) lithium di-silicate veneered PEEK FDP (sandblasting with 50 μm alumina: Group PCeS), and (iv) lithium di-silicate veneered PEEK FDP (chemical etching with 98% sulfuric acid: Group PCeE). The load-bearing capacity of all specimens was assessed using a universal test machine. All the samples were loaded till the cracking point and load at that point and failure modes were noted down. Statistical Analysis Used: One-way ANOVA and post hoc Tukey tests. Results: The highest load-bearing capacity was recorded for lithium di-silicate veneered PEEK copings which were chemically etched with 98% sulfuric acid (Group PCeE: 1040.25 ± 77.46) followed by Group PCeS (1017.20 ± 53.70), then Group PC (965 ± 51.57) and least was for Group PCeN (933 ± 97.54). There was a significant reduction in mean load-bearing capacity in Group PCeN (P < 0.05). Conclusions: Veneering of PEEK with pressed lithium di-silicate seems to be a viable clinical option in terms of adequate load-bearing capacity. Lithium di-silicate veneered PEEK FDPs were successful against physiological occlusal forces and are a suitable material for FDPs.Keywords
This publication has 25 references indexed in Scilit:
- Polyetheretherketone-A suitable material for fixed dental prostheses?Journal of Biomedical Materials Research Part B: Applied Biomaterials, 2013
- Effect of different surface pre-treatments and luting materials on shear bond strength to PEEKDental Materials, 2010
- Fracture behaviour of zirconia FPDs substructuresJournal of Oral Rehabilitation, 2010
- Load‐bearing capacity of all‐ceramic posterior inlay‐retained fixed dental prosthesesEuropean Journal of Oral Sciences, 2009
- Shear bond strengths between different zirconia cores and veneering ceramics and their susceptibility to thermocyclingDental Materials, 2008
- Fracture frequency of all-ceramic crowns during dynamic loading in a chewing simulator using different loading and luting protocolsDental Materials, 2008
- State of the art of zirconia for dental applicationsDental Materials, 2008
- A New Transitional Abutment for Immediate Aesthetics and FunctionImplant Dentistry, 2008
- Dental restorations for oral rehabilitation – testing of laboratory properties versus clinical performance for clinical decision making*Journal of Oral Rehabilitation, 2007
- Bite force and state of dentitionActa Odontologica Scandinavica, 1977