Site-Specific Retention of Colloids at Rough Rock Surfaces
- 3 August 2012
- journal article
- research article
- Published by American Chemical Society (ACS) in Environmental Science & Technology
- Vol. 46 (17) , 9378-9387
Abstract
The spatial deposition of polystyrene latex colloids (d = 1 μm) at rough mineral and rock surfaces was investigated quantitatively as a function of Eu(III) concentration. Granodiorite samples from Grimsel test site (GTS), Switzerland, were used as collector surfaces for sorption experiments. At a scan area of 300 × 300 μm2, the surface roughness (rms roughness, Rq) range was 100–2000 nm, including roughness contribution from asperities of several tens of nanometers in height to the sample topography. Although, an increase in both roughness and [Eu(III)] resulted in enhanced colloid deposition on granodiorite surfaces, surface roughness governs colloid deposition mainly at low Eu(III) concentrations (≤5 × 10–7 M). Highest deposition efficiency on granodiorite has been found at walls of intergranular pores at surface sections with roughness Rq = 500–2000 nm. An about 2 orders of magnitude lower colloid deposition has been observed at granodiorite sections with low surface roughness (Rq < 500 nm), such as large and smooth feldspar or quartz crystal surface sections as well as intragranular pores. The site-specific deposition of colloids at intergranular pores is induced by small scale protrusions (mean height = 0.5 ± 0.3 μm). These protrusions diminish locally the overall DLVO interaction energy at the interface. The protrusions prevent further rolling over the surface by increasing the hydrodynamic drag required for detachment. Moreover, colloid sorption is favored at surface sections with high density of small protrusions (density (D) = 2.6 ± 0.55 μm–1, asperity diameter (ϕ) = 0.6 ± 0.2 μm, height (h) = 0.4 ± 0.1 μm) in contrast to surface sections with larger asperities and lower asperity density (D = 1.2 ± 0.6 μm–1, ϕ = 1.4 ± 0.4 μm, h = 0.6 ± 0.2 μm). The study elucidates the importance to include surface roughness parameters into predictive colloid-borne contaminant migration calculations.Keywords
This publication has 71 references indexed in Scilit:
- Deposition of Latex Colloids at Rough Mineral Surfaces: An Analogue Study Using Nanopatterned SurfacesLangmuir, 2012
- Effect of colloids on transfer of radionuclides by subsurface waterGeology of Ore Deposits, 2009
- Role of bentonite colloids on europium and plutonium migration in a granite fractureApplied Geochemistry, 2008
- DLVO interaction energy between a sphere and a nano-patterned plateColloids and Surfaces A: Physicochemical and Engineering Aspects, 2008
- Bentonite colloid diffusion through the host rock of a deep geological repositoryPhysics and Chemistry of the Earth, Parts A/B/C, 2007
- Particle Deposition onto Solid Surfaces with Micropatterned Charge Heterogeneity: The “Hydrodynamic Bump” EffectLangmuir, 2003
- The colloid and radionuclide retardation experiment at the Grimsel Test Site: influence of bentonite colloids on radionuclide migration in a fractured rockColloids and Surfaces A: Physicochemical and Engineering Aspects, 2003
- The interactions of amphiphilic latexes with surfaces: the effect of surface modifications and ionic strengthPolymer, 2002
- Transport of polydisperse colloids in a saturated fracture with spatially variable apertureWater Resources Research, 2000
- Studies on adsorption of guar gum onto biotite micaMinerals Engineering, 1997