Effect of wall thickness of 3D‐printed models on resisting deformation from thermal forming in‐office aligners
Open Access
- 3 February 2024
- journal article
- research article
- Published by Wiley in Clinical and Experimental Dental Research
- Vol. 10 (1) , e827
Abstract
Background: Fabricating clear aligners by thermoforming three‐dimensional printed dental models requires a high degree of accuracy. It is unknown whether model thickness affects the accuracy when used to thermoform aligners.Purpose: This research utilizes three‐dimensional printed models made with differing wall thicknesses to determine its effect on their ability to withstand deformation during aligner fabrication.Methods: A total of 50 models of different wall thickness (10 each of 0.5, 1.0, 1.5, 2.0 mm, and solid) were printed using model resin (Model V2, Formlabs) on a low‐force stereolithography printer (Form 3B, Formlabs). Aligners were then fabricated using a thermal pressure forming machine (Biostar V, Great Lakes Dental Technologies) utilizing 25 s cycles to adapt 0.030″ acrylic sheets (Invisacryl, Great Lakes Dental Technologies), then removed from the models and sprayed with a contrast powder (Optispray, Dentsply Sirona) to aid in scanning with an intraoral scanner (CEREC Primescan, Dentsply Sirona). Each aligner's data was then compared to the original file used for printing with 3D comparison software (Geomagic Control X, 3D Systems).Results: The results show model thickness greater than or equal to 2.0 mm produced clinically acceptable results within the margin of error (0.3 mm). A total of 0.5 mm thickness failed to withstand thermal forming in 4 of the 10 trials. A total of 0.5 mm produced 27.56% of results in tolerance, 1.0 mm produced 75.66% of results in tolerance, 1.5 mm had 80.38% of results in tolerance, 86.82% of 2 mm models were in tolerance, and solid had 96.45% of results in tolerance.Conclusion: Hollow models of thicknesses 2.0 mm and solid models produced clinically acceptable aligners while utilizing less resin per unit compared to solid models, thus being more cost effective, time efficient and eco‐friendly. Therefore, a recommendation can be made to print hollow models with a shell thickness of greater than 2.0 mm for aligner fabrication.Keywords
This publication has 16 references indexed in Scilit:
- Effects of Postcuring Temperature on the Mechanical Properties and Biocompatibility of Three-Dimensional Printed Dental Resin MaterialPolymers, 2021
- Evaluation of the dimensional accuracy of thermoformed appliances taken from 3D printed models with varied shell thicknesses: An in vitro studyInternational Orthodontics, 2021
- Effect of print orientation and duration of ultraviolet curing on the dimensional accuracy of a 3-dimensionally printed orthodontic clear aligner designAmerican Journal of Orthodontics and Dentofacial Orthopedics, 2020
- Analysis of the thickness of 3-dimensional-printed orthodontic alignersAmerican Journal of Orthodontics and Dentofacial Orthopedics, 2020
- Digital Intraoral Scanners and Alginate Impressions in Reproducing Full Dental Arches: A Comparative 3D AssessmentApplied Sciences, 2020
- Accuracy of 3-Dimensionally Printed Full-Arch Dental Models: A Systematic ReviewJournal of Clinical Medicine, 2020
- Evaluation of fit for 3D-printed retainers compared with thermoform retainersAmerican Journal of Orthodontics and Dentofacial Orthopedics, 2019
- Precision and trueness of dental models manufactured with different 3-dimensional printing techniquesAmerican Journal of Orthodontics and Dentofacial Orthopedics, 2018
- Accuracy and mechanical properties of orthodontic models printed 3-dimensionally from calcium sulfate before and after various postprinting treatmentsAmerican Journal of Orthodontics and Dentofacial Orthopedics, 2016
- Three-dimensional printing technology.2014