Numerical investigation of the effectiveness of a bored pile wall for the minimisation of settlement resulting from tunnel driving
- 13 November 2009
- journal article
- topics
- Published by Wiley in Geomechanics and Tunnelling
- Vol. 2 (6) , 753-765
Abstract
Bored pile walls can be constructed between buildings and tunnel alignments to protect sensitive buildings from settlement resulting from tunnelling. The aim of the research work presented here was to evaluate the effectiveness of such a bored pile wall with FE calculations and identify influential parameters. Two methods of predicting settlement were investigated with the programme ABAQUS: The GAP method, where the deformations of the tunnel contour are prescribed, and the stress reduction method, with which the support pressure at the tunnel contour is reduced. The ground is modelled as linear‐elastic, ideal‐plastic with a Mohr‐Coulomb failure criterion as well as with a hypoplastic constitutive law. The contact surface between wall and ground was modelled with complete bonding as well as with a contact law with friction.The simulation results with the stress reduction method and the hypoplastic material model show the best results qualitatively. The predict settlements agree well with empirical methods and centrifuge tests from the literature. The simulations show that the effectiveness of the wall is significantly influenced by the contact properties in the boundary surface. It achieves the best protection effect when frictionless.Zur Abschirmung sensibler Gebäude vor Setzungen infolge Tunnelvortrieb können Bohrpfahlwände zwischen Gebäude und Tunneltrasse eingesetzt werden. Ziel der hier präsentierten Forschungsarbeit war es, die Wirksamkeit einer solchen Bohrpfahlwand mit FE‐Berechnungen nachzuvollziehen und Einflussparameter zu identifizieren. Mit dem Programm ABAQUS wurden zwei Möglichkeiten zur Setzungsprognose untersucht: Die GAPMethode, bei der die Verschiebungen der Tunnelkontur vorgegeben werden, und die Spannungsreduktions‐Methode, bei welcher der Stützdruck an der Tunnelkontur reduziert wird. Der Boden wurde als linear‐elastisch, ideal‐plastisch mit Grenzbedingung nach Mohr‐Coulomb sowie mit einem hypoplastischen Stoffgesetz modelliert. Die Kontaktfläche zwischen Wand und Boden wurde sowohl mit vollständigem Verbund als auch mit einem Kontaktgesetz mit Reibung modelliert.Die Simulationsergebnisse mit der Spannungsreduktions‐Methode und dem hypoplastischen Materialmodell zeigen die qualitativ besten Ergebnisse. Die Setzungsprognosen stimmen gut mit empirischen Ansätzen und Zentrifugenversuchen aus der Literatur überein. Die Simulationen veranschaulichen, dass die Wirksamkeit der Wand maßgeblich von den Kontakteigenschaften in der Grenzfläche beeinflusst wird. Die größte Abschirmwirkung erzielt sie bei Reibungsfreiheit.Keywords
This publication has 12 references indexed in Scilit:
- Prediction of stresses and strains around model tunnels with adjacent embedded walls in overconsolidated clayComputers and Geotechnics, 2009
- Impact of constitutive models on the numerical analysis of underground constructionsActa Geotechnica, 2008
- Appraising the methods accounting for 3D tunnelling effects in 2D plane strain FE analysisTunnelling and Underground Space Technology, 2007
- Finite Element Analysis in Geotechnical Engineering: Volume two - Application2001
- Introduction to Hypoplasticity2000
- The influence of pre-failure soil stiffness on the numerical analysis of tunnel constructionGéotechnique, 1997
- A hypoplastic relation for granular materials with a predefined limit state surfaceMechanics of Cohesive-frictional Materials, 1996
- Subsidence owing to tunnelling. I. Estimating the gap parameterCanadian Geotechnical Journal, 1992
- A method of estimating surface settlement above tunnels constructed in soft groundCanadian Geotechnical Journal, 1983
- A rate-dependent constitutive equation for soilsMechanics Research Communications, 1977