Thermal, crystallization, mechanical and decomposition properties of poly(lactic acid) plasticized with poly(ethylene glycol)
- 22 January 2018
- journal article
- research article
- Published by Wiley in Journal of Vinyl and Additive Technology
- Vol. 24 (S1) , E154-E163
Abstract
In order to modify the brittleness of poly(lactic acid) (PLA), a series of PLA/poly(ethylene glycol) (PEG) blends were prepared by the solution‐cast technique using PEG as a plasticizer. The thermal, crystallization, mechanical, and hydrophilic properties of the PLA/PEG blends were compared with those of neat PLA. It is concluded that the PLA/PEG blends change from miscible to partially miscible at the critical PEG content of 10 wt%. Above 10 wt% PEG content, the miscible PLA/PEG blends occur the phase separation, and the PEG component does not co‐crystallize with PLA component with PLA and PEG crystallizing separately. The introduction of PEG reduces the intermolecular force and enhances the mobility of PLA chains, thus improving the crystallization capacity and flexibility of PLA. The PLA/PEG blends show plastic fracture behavior, yielding higher elongation and lower modulus values compared with neat PLA. Below 30 wt% PEG content, blending with PEG significantly decreases the modulus and yield stress and increases the fracture strain of PLA with an increase in the PEG content. Whereas above 30 wt% PEG content, the crystallization of PEG component results in an increase in modulus and a corresponding decrease in elongation at break of the blends. The thermal degradation temperature is in the range of 320–330°C for PLA/PEG blends, in comparison with 375°C for neat PLA. At ambient temperature, the desired mechanical properties are achieved by blending PLA with 30 wt% PEG. The PEG plasticizer is compatible with the PLA matrix and has a relatively low migration rate toward the blend surfaces with a low PEG content (≤30 wt%). J. VINYL ADDIT. TECHNOL., 24:E154–E163, 2018. © 2018 Society of Plastics EngineersKeywords
Funding Information
- National Nature Science Foundation of China (51303139)
- Educational Commission of Hubei Province of China (Q20121710)
This publication has 29 references indexed in Scilit:
- A method for simultaneously improving the flame retardancy and toughness of PLAPolymers for Advanced Technologies, 2011
- Morphology, thermal behavior and mechanical properties of binary blends of compatible biosourced polymers: Polylactide/polyamide11Polymer, 2011
- Kinetics of water absorption and thermal properties of poly(lactic acid)/organomontmorillonite/poly(ethylene glycol) nanocompositesJournal of Vinyl and Additive Technology, 2011
- EFFECTS OF BLENDING CHITOSAN WITH PEG ON SURFACE MORPHOLOGY, CRYSTALLIZATION AND THERMAL PROPERTIESChinese Journal of Polymer Science, 2009
- Polylactide (PLA) designed with desired end‐use properties: 1. PLA compositions with low molecular weight ester‐like plasticizers and related performancesPolymers for Advanced Technologies, 2008
- Plasticization of Poly(l-lactide) with Poly(propylene glycol)Biomacromolecules, 2006
- Porous poly(L‐lactic acid)/poly(ethylene glycol) blend filmsJournal of Applied Polymer Science, 2004
- Aging of poly(lactide)/poly(ethylene glycol) blends. Part 1. Poly(lactide) with low stereoregularityPolymer, 2003
- Miscibility and phase structure of binary blends of polylactide and poly(vinylpyrrolidone)Journal of Applied Polymer Science, 2003
- Crystallization from the melt of poly(lactide)s with different optical purities and their blendsMacromolecular Chemistry and Physics, 1996