Siebe Broersma
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Siebe Broersma has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Andy van Den Dobbelsteen
Department of Architecture, Faculty of Architecture and the Built Environment, Delft University of Technology (TU Delft), 2628 BL Delft, The Netherlands
1 shared publication - Hamida Kurniawati
Department of Architecture, Engineering, and Technology, Delft University of Technology, Mekelweg 5, 2628 CD Delft, The Netherlands
1 shared publication - Laure Itard
Delft University of Technology
1 shared publication - Michiel Fremouw
Faculty of Architecture and the Built Environment, Department of Architectural Engineering + Technology, Delft University of Technology, 2628 BL Delft, The Netherlands
1 shared publication - Saleh Mohammadi
MNEXT, Avans University of Applied Sciences, Building LD, Lovensdijkstraat 63, 4818 AJ Breda, and HZ University of Applied Sciences, Het Groene Woud 1, 4331 NB Middelburg, The Netherlands; Tel.: +31-(0)-6-24969861
1 shared publication
Latest Publications
- Open Access
Integrated Hydrogen in Buildings: Energy Performance Comparisons of Green Hydrogen Solutions in the Built Environment
This study investigates the integration of green hydrogen into building energy systems using local solar power, with the electricity grid serving as a backup plan. A comprehensive bottom-up analysis compares six energy system configurations: the natural gas grid boiler system, all-electric heat pump system, natural gas and hydrogen blended system, hydrogen microgrid boiler system, cogeneration hydrogen fuel cell system, and hybrid hydrogen heat pump system. Energy efficiency evaluations were conducted for 25 homes within one block in a neighborhood across five typological house stocks located in Stoke-on-Trent, UK. This research was modeled using a spreadsheet-based approach. The results highlight that while the all-electric heat pump system still demonstrates the highest energy efficiency with the lowest consumption, the hybrid hydrogen heat pump system emerges as the most efficient hydrogen-based solution. Further optimization, through the implementation of a peak-shaving strategy, shows promise in enhancing system performance. In this approach, hybrid hydrogen serves as a heating source during peak demand hours (evenings and cold seasons), complemented by a solar energy powered heat pump during summer and daytime. An hourly operational configuration is recommended to ensure consistent performance and sustainability. This study focuses on energy performance, excluding cost-effectiveness analysis. Therefore, the cost of the energy is not taken into consideration, requiring further development for future research in these areas.
Open AccessIntegrated Hydrogen in Buildings: Energy Performance Comparisons of Green Hydrogen Solutions in the Built Environment
This study investigates the integration of green hydrogen into building energy systems using local solar power, with the electricity grid serving as a backup plan. A comprehensive bottom-up analysis compares six energy system configurations: the natural gas grid boiler system, all-electric heat pump system, natural gas and hydrogen blended system, hydrogen microgrid boiler system, cogeneration hydrogen fuel cell system, and hybrid hydrogen heat pump system. Energy efficiency evaluations were conducted for 25 homes within one block in a neighborhood across five typological house stocks located in Stoke-on-Trent, UK. This research was modeled using a spreadsheet-based approach. The results highlight that while the all-electric heat pump system still demonstrates the highest energy efficiency with the lowest consumption, the hybrid hydrogen heat pump system emerges as the most efficient hydrogen-based solution. Further optimization, through the implementation of a peak-shaving strategy, shows promise in enhancing system performance. In this approach, hybrid hydrogen serves as a heating source during peak demand hours (evenings and cold seasons), complemented by a solar energy powered heat pump during summer and daytime. An hourly operational configuration is recommended to ensure consistent performance and sustainability. This study focuses on energy performance, excluding cost-effectiveness analysis. Therefore, the cost of the energy is not taken into consideration, requiring further development for future research in these areas.
- Open Access
Energy Potential Mapping: Visualising Energy Characteristics for the Exergetic Optimisation of the Built Environment
It is difficult to fully satisfy the energy demand of today’s society with renewables. Nevertheless, most of the energy we use is lost as non-functional waste energy, whereas a large part of the built environment’s energy demand is only for low-quality energy, so the initial demand for primary, high-quality energy can be reduced by more effective usage, such as by low-exergy means. Gaining insight into the parameters of energy demands and local renewable and residual energy potentials enables matching energy demand with a fitting potential, not only concerning quantity but taking into account location, temporality and quality as well. The method of Energy Potential Mapping (EPM) aims to visualise the energy potentials and demands by making information of quantity, quality and location of demand and supply accessible. The aspect of quality specifically applies to heat and cold. The methodology of EPM will be described and explained with case studies. The focus specifically lies on mapping heat (and cold), one of the main reasons for energy demand in the built environment. The visualisation of exergy, to be simplified as the quality of energy, becomes an extra parameter in the case of Dutch Heat Maps. These maps can help finding opportunities of practical implementations of exchanging or cascading heat or cold. This way EPM and Heat Mapping (HM) enables application of exergy principles in the built environment. EPM and HM can be seen as a local energy catalogue and can be useful in spatial planning for energy-based urban and rural plans.
Open AccessEnergy Potential Mapping: Visualising Energy Characteristics for the Exergetic Optimisation of the Built Environment
It is difficult to fully satisfy the energy demand of today’s society with renewables. Nevertheless, most of the energy we use is lost as non-functional waste energy, whereas a large part of the built environment’s energy demand is only for low-quality energy, so the initial demand for primary, high-quality energy can be reduced by more effective usage, such as by low-exergy means. Gaining insight into the parameters of energy demands and local renewable and residual energy potentials enables matching energy demand with a fitting potential, not only concerning quantity but taking into account location, temporality and quality as well. The method of Energy Potential Mapping (EPM) aims to visualise the energy potentials and demands by making information of quantity, quality and location of demand and supply accessible. The aspect of quality specifically applies to heat and cold. The methodology of EPM will be described and explained with case studies. The focus specifically lies on mapping heat (and cold), one of the main reasons for energy demand in the built environment. The visualisation of exergy, to be simplified as the quality of energy, becomes an extra parameter in the case of Dutch Heat Maps. These maps can help finding opportunities of practical implementations of exchanging or cascading heat or cold. This way EPM and Heat Mapping (HM) enables application of exergy principles in the built environment. EPM and HM can be seen as a local energy catalogue and can be useful in spatial planning for energy-based urban and rural plans.