Virginie Vandenbossche
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Virginie Vandenbossche has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Luc Rigal
Université de Toulouse, INP-ENSIACET, LCA (Laboratoire de Chimie Agro-industrielle), 4 Allée Emile Monso, F-31030 Toulouse, France; INRA, UMR 1010 CAI, F-31030 Toulouse, France
2 shared publications - Antoine Rouilly
Laboratoire de Chimie Agro-Industrielle, UMR 1010 INRA/INP-ENSIACET, 118 Route de Narbonne, F-31077 Toulouse Cedex 04, France
1 shared publication Catherine Doumeng
Université de Toulouse, INP, Laboratoire de Chimie Agro-industrielle, ENSIACET, 4 Allée Emile Monso, BP 44362, 31030 Toulouse Cedex 4, France; INRA, UMR 1010, Laboratoire de Chimie Agro-industrielle, 31030 Toulouse Cedex 4, France
1 shared publication- David Viet
The Green Factory, 27 rue Chanez, Paris 75016, France
1 shared publication - Etienne Gatt
Laboratoire de Chimie Agro-Industrielle, LCA, Université de Toulouse, INRA, Toulouse, France
1 shared publication Julien Bley
Centre de recherche sur les matériaux lignocellulosiques, Université du Québec à Trois-Rivières, Canada; Innofibre, 3351 Boulevard des Forges, Québec G9A 5E6, Canada
1 shared publication
Latest Publications
- Open Access
- 30 March 2015
- Published by Macrothink Institute, Inc. in Journal of Agricultural Studies
- Vol. 3 (2) , 194-211
New insulation fiberboards from sunflower cake with improved thermal and mechanical properties
New thermal insulation fiberboards were manufactured by compression molding from a cake generated during the sunflower biorefinery. Fiberboards were cohesive mixtures of a natural binder and lignocellulosic fibers from sunflower cake. The natural binder ensured the board cohesion, and fibers acted as reinforcing fillers. The influence of molding conditions, i.e. binder type and binder content, on board density, mechanical and heat insulation properties was examined. The medium-density board containing 20% starch-based binder was a good compromise between mechanical and heat insulation properties (78 mW/m K thermal conductivity). It could be positioned on walls and ceilings for thermal insulation of buildings.
- 30 March 2015
- Published by Macrothink Institute, Inc. in Journal of Agricultural Studies
- Vol. 3 (2) , 194-211
Open AccessNew insulation fiberboards from sunflower cake with improved thermal and mechanical properties
New thermal insulation fiberboards were manufactured by compression molding from a cake generated during the sunflower biorefinery. Fiberboards were cohesive mixtures of a natural binder and lignocellulosic fibers from sunflower cake. The natural binder ensured the board cohesion, and fibers acted as reinforcing fillers. The influence of molding conditions, i.e. binder type and binder content, on board density, mechanical and heat insulation properties was examined. The medium-density board containing 20% starch-based binder was a good compromise between mechanical and heat insulation properties (78 mW/m K thermal conductivity). It could be positioned on walls and ceilings for thermal insulation of buildings.
- Open Access
- 4 November 2013
- Published by BioResources in BioResources
- Vol. 9 (1) , 1519-1538
Thermomechanical and Thermo-mechano-chemical Pretreatment of Wheat Straw using a Twin-screw Extruder
Thermomechanical and Thermo-mechano-chemical Pretreatment of Wheat Straw using a Twin-screw Extruder
- 4 November 2013
- Published by BioResources in BioResources
- Vol. 9 (1) , 1519-1538
Open AccessThermomechanical and Thermo-mechano-chemical Pretreatment of Wheat Straw using a Twin-screw Extruder
Thermomechanical and Thermo-mechano-chemical Pretreatment of Wheat Straw using a Twin-screw Extruder
- Open Access
High Pressure Compression-Molding of α-Cellulose and Effects of Operating Conditions
Commercial α-cellulose was compression-molded to produce 1A dog-bone specimens under various operating conditions without any additive. The resulting agromaterials exhibited a smooth, plastic-like surface, and constituted a suitable target as replacement for plastic materials. Tensile and three-points bending tests were conducted according to ISO standards related to the evaluation of plastic materials. The specimens had strengths comparable to classical petroleum-based thermoplastics. They also exhibited high moduli, which is characteristic of brittle materials. A higher temperature and higher pressure rate produced specimens with higher mechanical properties while low moisture content produced weaker specimens. Generally, the strong specimen had higher specific gravity and lower moisture content. However, some parameters did not follow the general trend e.g., thinner specimen showed much higher Young’s Modulus, although their specific gravity and moisture content remained similar to control, revealing a marked skin-effect which was confirmed by SEM observations.
Open AccessHigh Pressure Compression-Molding of α-Cellulose and Effects of Operating Conditions
Commercial α-cellulose was compression-molded to produce 1A dog-bone specimens under various operating conditions without any additive. The resulting agromaterials exhibited a smooth, plastic-like surface, and constituted a suitable target as replacement for plastic materials. Tensile and three-points bending tests were conducted according to ISO standards related to the evaluation of plastic materials. The specimens had strengths comparable to classical petroleum-based thermoplastics. They also exhibited high moduli, which is characteristic of brittle materials. A higher temperature and higher pressure rate produced specimens with higher mechanical properties while low moisture content produced weaker specimens. Generally, the strong specimen had higher specific gravity and lower moisture content. However, some parameters did not follow the general trend e.g., thinner specimen showed much higher Young’s Modulus, although their specific gravity and moisture content remained similar to control, revealing a marked skin-effect which was confirmed by SEM observations.