Zoran Ren
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Zoran Ren has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Matej Vesenjak
Univerza v Mariboru, Fakulteta za strojništvo
3 shared publications - Matej Borovinsek
Faculty of Mechanical Engineering, University of Maribor, Maribor 2000, Slovenia
2 shared publications - A. Öchsner
Technical University of Malaysia
1 shared publication - Gorazd Fajdiga
Biotechnical Faculty, University of Ljubljana, Jamnikarjeva 101, 1000 Ljubljana, Slovenia
1 shared publication - Joze Flasker1 shared publication
Jože Flašker
University of Maribor, Faculty of Mechanical Engineering, Smetanova ul. 17, 2000 Maribor, Slovenia
1 shared publication
Latest Publications
- Open Access
Behavior of Metallic Foam under Shock Wave Loading
In this manuscript, the behavior of metallic foam under impact loading and shock wave propagation has been observed. The goal of this research was to investigate the material and structural properties of submerged open-cell aluminum foam under impact loading conditions with particular interest in shock wave propagation and its effects on cellular material deformation. For this purpose experimental tests and dynamic computational simulations of aluminum foam specimens inside a water tank subjected to explosive charge have been performed. Comparison of the results shows a good correlation between the experimental and simulation results.
Open AccessBehavior of Metallic Foam under Shock Wave Loading
In this manuscript, the behavior of metallic foam under impact loading and shock wave propagation has been observed. The goal of this research was to investigate the material and structural properties of submerged open-cell aluminum foam under impact loading conditions with particular interest in shock wave propagation and its effects on cellular material deformation. For this purpose experimental tests and dynamic computational simulations of aluminum foam specimens inside a water tank subjected to explosive charge have been performed. Comparison of the results shows a good correlation between the experimental and simulation results.
- 15 August 2011
- Published by MAFTREE in International Journal of Vehicle Structures & Systems
- Vol. 3 (3)
Computational and Experimental Testing of the Steel Reinforced Wooden Road Safety Barrier
- 15 August 2011
- Published by MAFTREE in International Journal of Vehicle Structures & Systems
- Vol. 3 (3)
Computational and Experimental Testing of the Steel Reinforced Wooden Road Safety Barrier
- 7 October 2008
- Published by Springer Nature in Experimental Mechanics
- Vol. 49 (4) , 501-509
Experimental Study of Open-Cell Cellular Structures with Elastic Filler Material
- 7 October 2008
- Published by Springer Nature in Experimental Mechanics
- Vol. 49 (4) , 501-509
Experimental Study of Open-Cell Cellular Structures with Elastic Filler Material
- 30 November 2002
- Published by Elsevier in Computers & Structures
- Vol. 80 (27-30) , 2209-2216
Computational service life estimation of contacting mechanical elements in regard to pitting
- 30 November 2002
- Published by Elsevier in Computers & Structures
- Vol. 80 (27-30) , 2209-2216
Computational service life estimation of contacting mechanical elements in regard to pitting
- 17 July 2001
- Published by Wiley in Communications in Numerical Methods in Engineering
- Vol. 17 (8) , 529-541
Computational modelling of the surface fatigue crack growth on gear teeth flanks
The paper describes a 2‐dimensional computational model for simulation of the surface initiated fatigue crack growth in the contact area of gear teeth flanks that leads to surface pitting. The discretized model of a gear tooth with the assumed initial crack is subjected to normal contact pressure, which takes into account the EHD‐lubrication conditions and tangential loading due to friction between gear teeth flanks. The model accounts also for the influence of a fluid driven into the crack by hydraulic mechanism on crack propagation. The J‐integral method in the framework of the finite element analysis is used for simulation of the fatigue crack propagation from the initial to the critical crack length, when the surface material layer breaks away and pit appears on the surface. The model is applied to a real pitting problem of a gear and corresponding computational results in terms of pit sizes correlate well to the development of micropits observed in experimental testing. Copyright © 2001 John Wiley & Sons, Ltd.
- 17 July 2001
- Published by Wiley in Communications in Numerical Methods in Engineering
- Vol. 17 (8) , 529-541
Computational modelling of the surface fatigue crack growth on gear teeth flanks
The paper describes a 2‐dimensional computational model for simulation of the surface initiated fatigue crack growth in the contact area of gear teeth flanks that leads to surface pitting. The discretized model of a gear tooth with the assumed initial crack is subjected to normal contact pressure, which takes into account the EHD‐lubrication conditions and tangential loading due to friction between gear teeth flanks. The model accounts also for the influence of a fluid driven into the crack by hydraulic mechanism on crack propagation. The J‐integral method in the framework of the finite element analysis is used for simulation of the fatigue crack propagation from the initial to the critical crack length, when the surface material layer breaks away and pit appears on the surface. The model is applied to a real pitting problem of a gear and corresponding computational results in terms of pit sizes correlate well to the development of micropits observed in experimental testing. Copyright © 2001 John Wiley & Sons, Ltd.
- 1 March 1999
- Published by Taylor & Francis in Technology, Law and Insurance
- Vol. 4 (1-2) , 137-144
Influence of inclusion interfaces on surface pitting
A new model is described for the simulation of the surface fatigue process in the contact area of spur gears. The model considers the conditions required for subsurface fatigue crack initiation and allows for proper simulation of fatigue crack propagation under contact loading. The theory of dislocation motion along inclusion interfaces is studied in some detail and is used to describe the process of fatigue crack initiation, where the microstructure of a material plays a crucial role. The theory of short crack growth is then used for the simulation of the fatigue crack growth. The stress field in the contact area and the functional relationship between the stress intensity factor and crack length are determined by the finite element method. The 2-dimensional equivalent model of two cylinders is used in the numerical simulations of crack initiation and crack propagation in the contact area, which reduces the required computation time significantly. On the basis of computational results, and with consideration of some particular material parameters, the service life of gear teeth with regard to pitting is estimated. The model developed is applied to a real spur gear pair, which also is tested experimentally. A comparison of numerical and experimental results reveals good agreement, and it may be concluded that the model developed is appropriate for determining the pitting resistance of gear teeth.
- 1 March 1999
- Published by Taylor & Francis in Technology, Law and Insurance
- Vol. 4 (1-2) , 137-144
Influence of inclusion interfaces on surface pitting
A new model is described for the simulation of the surface fatigue process in the contact area of spur gears. The model considers the conditions required for subsurface fatigue crack initiation and allows for proper simulation of fatigue crack propagation under contact loading. The theory of dislocation motion along inclusion interfaces is studied in some detail and is used to describe the process of fatigue crack initiation, where the microstructure of a material plays a crucial role. The theory of short crack growth is then used for the simulation of the fatigue crack growth. The stress field in the contact area and the functional relationship between the stress intensity factor and crack length are determined by the finite element method. The 2-dimensional equivalent model of two cylinders is used in the numerical simulations of crack initiation and crack propagation in the contact area, which reduces the required computation time significantly. On the basis of computational results, and with consideration of some particular material parameters, the service life of gear teeth with regard to pitting is estimated. The model developed is applied to a real spur gear pair, which also is tested experimentally. A comparison of numerical and experimental results reveals good agreement, and it may be concluded that the model developed is appropriate for determining the pitting resistance of gear teeth.
- 15 September 1998
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 43 (1) , 33-50
Simulation of surface pitting due to contact loading
- 15 September 1998
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 43 (1) , 33-50
Simulation of surface pitting due to contact loading