Marc M. J. Koppert
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Marc M. J. Koppert has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Anita Driessen-Mol
Department of Biomedical Engineering, Eindhoven University of Technology , Eindhoven, The Netherlands
1 shared publication - Bart M. ter Haar Romeny
Eindhoven University of Technology
1 shared publication - Carlijn V. C. Bouten
Department of Biomedical Engineering, Eindhoven University of Technology, Eindhoven, The Netherlands
1 shared publication - Frank P. T. Baaijens
Department of Biomedical Engineering, Eindhoven University of Technology, Eindhoven, The Netherlands
1 shared publication - Hans C. van Assen
Department of Radiology Leiden University Medical Center Leiden The Netherlands
1 shared publication - Mirjam P. Rubbens
Department of Biomedical Engineering, Eindhoven University of Technology, Eindhoven, The Netherlands
1 shared publication
Latest Publications
- Open Access
- 5 May 2009
- Published by Springer Nature in Annals of Biomedical Engineering
- Vol. 37 (7) , 1263-1272
Quantification of the Temporal Evolution of Collagen Orientation in Mechanically Conditioned Engineered Cardiovascular Tissues
Load-bearing soft tissues predominantly consist of collagen and exhibit anisotropic, non-linear visco-elastic behavior, coupled to the organization of the collagen fibers. Mimicking native mechanical behavior forms a major goal in cardiovascular tissue engineering. Engineered tissues often lack properly organized collagen and consequently do not meet in vivo mechanical demands. To improve collagen architecture and mechanical properties, mechanical stimulation of the tissue during in vitro tissue growth is crucial. This study describes the evolution of collagen fiber orientation with culture time in engineered tissue constructs in response to mechanical loading. To achieve this, a novel technique for the quantification of collagen fiber orientation is used, based on 3D vital imaging using multiphoton microscopy combined with image analysis. The engineered tissue constructs consisted of cell-seeded biodegradable rectangular scaffolds, which were either constrained or intermittently strained in longitudinal direction. Collagen fiber orientation analyses revealed that mechanical loading induced collagen alignment. The alignment shifted from oblique at the surface of the construct towards parallel to the straining direction in deeper tissue layers. Most importantly, intermittent straining improved and accelerated the alignment of the collagen fibers, as compared to constraining the constructs. Both the method and the results are relevant to create and monitor load-bearing tissues with an organized anisotropic collagen network.
- 5 May 2009
- Published by Springer Nature in Annals of Biomedical Engineering
- Vol. 37 (7) , 1263-1272
Open AccessQuantification of the Temporal Evolution of Collagen Orientation in Mechanically Conditioned Engineered Cardiovascular Tissues
Load-bearing soft tissues predominantly consist of collagen and exhibit anisotropic, non-linear visco-elastic behavior, coupled to the organization of the collagen fibers. Mimicking native mechanical behavior forms a major goal in cardiovascular tissue engineering. Engineered tissues often lack properly organized collagen and consequently do not meet in vivo mechanical demands. To improve collagen architecture and mechanical properties, mechanical stimulation of the tissue during in vitro tissue growth is crucial. This study describes the evolution of collagen fiber orientation with culture time in engineered tissue constructs in response to mechanical loading. To achieve this, a novel technique for the quantification of collagen fiber orientation is used, based on 3D vital imaging using multiphoton microscopy combined with image analysis. The engineered tissue constructs consisted of cell-seeded biodegradable rectangular scaffolds, which were either constrained or intermittently strained in longitudinal direction. Collagen fiber orientation analyses revealed that mechanical loading induced collagen alignment. The alignment shifted from oblique at the surface of the construct towards parallel to the straining direction in deeper tissue layers. Most importantly, intermittent straining improved and accelerated the alignment of the collagen fibers, as compared to constraining the constructs. Both the method and the results are relevant to create and monitor load-bearing tissues with an organized anisotropic collagen network.