Alan M. Shih
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Alan M. Shih has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Yasushi Ito
Japan Aerospace Exploration Agency
5 shared publications - Bharat K. Soni
A Department of Mechanical Engineering, University of Alabama at Birmingham, USA
3 shared publications - Gary C. Cheng
Department of Mechanical Engineering, University of Alabama at Birmingham, USA
2 shared publications - Kazuhiro Nakahashi
Tohoku University
2 shared publications - Peter Daniel Waite
University of Alabama at Birmingham School of Dentistry and Medicine
2 shared publications - Roy P. Koomullil
University of Alabama at Birmingham
2 shared publications
Latest Publications
- 1 December 2014
- Published by Elsevier in Mathematics and Computers in Simulation
- Vol. 106, 44-59
Assessment of surgical effects on patients with obstructive sleep apnea syndrome using computational fluid dynamics simulations
- 1 December 2014
- Published by Elsevier in Mathematics and Computers in Simulation
- Vol. 106, 44-59
Assessment of surgical effects on patients with obstructive sleep apnea syndrome using computational fluid dynamics simulations
- 1 May 2011
- Published by Elsevier in Mathematics and Computers in Simulation
- Vol. 81 (9) , 1876-1891
Patient-specific geometry modeling and mesh generation for simulating Obstructive Sleep Apnea Syndrome cases by Maxillomandibular Advancement
- 1 May 2011
- Published by Elsevier in Mathematics and Computers in Simulation
- Vol. 81 (9) , 1876-1891
Patient-specific geometry modeling and mesh generation for simulating Obstructive Sleep Apnea Syndrome cases by Maxillomandibular Advancement
- 2 March 2011
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 87 (13) , 1254-1277
A novel hole patching algorithm for discrete geometry using non‐uniform rational B‐spline
A hole patching algorithm for discrete geometry using a parametric approach based on Non‐Uniform Rational B‐Spline (NURBS) curves and surfaces is being presented in this paper. This algorithm is focused on recovering the missing geometric information based on the neighboring points surrounding the topologically simple but geometrically complex holes. The neighboring points are utilized to reconstruct a set of three‐dimensional (3D) NURBS surface patches covering the hole region which in turn are used to produce a smooth surface patch covering the hole. This algorithm can automatically identify the hole, obtain surrounding points, create the NURBS surfaces, and perform the projection of points onto the surface to complete the process. The algorithm also provides a way for the user to control the size and density of triangulation in the patches matching that of the surroundings. This paper describes the algorithm step by step in detail with a test case for description purposes. The validation of the algorithm is performed on several analytical geometries to assess the accuracy of the algorithm. Several complex geometries are used to demonstrate the success and robustness of the algorithm. Finally, a conclusion provides the overall assessment of this research and identifies its weaknesses for future improvements. Copyright © 2011 John Wiley & Sons, Ltd.
- 2 March 2011
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 87 (13) , 1254-1277
A novel hole patching algorithm for discrete geometry using non‐uniform rational B‐spline
A hole patching algorithm for discrete geometry using a parametric approach based on Non‐Uniform Rational B‐Spline (NURBS) curves and surfaces is being presented in this paper. This algorithm is focused on recovering the missing geometric information based on the neighboring points surrounding the topologically simple but geometrically complex holes. The neighboring points are utilized to reconstruct a set of three‐dimensional (3D) NURBS surface patches covering the hole region which in turn are used to produce a smooth surface patch covering the hole. This algorithm can automatically identify the hole, obtain surrounding points, create the NURBS surfaces, and perform the projection of points onto the surface to complete the process. The algorithm also provides a way for the user to control the size and density of triangulation in the patches matching that of the surroundings. This paper describes the algorithm step by step in detail with a test case for description purposes. The validation of the algorithm is performed on several analytical geometries to assess the accuracy of the algorithm. Several complex geometries are used to demonstrate the success and robustness of the algorithm. Finally, a conclusion provides the overall assessment of this research and identifies its weaknesses for future improvements. Copyright © 2011 John Wiley & Sons, Ltd.
- 1 January 2011
- Published by Springer Nature
- p. 387-403
Hybrid Approach for Repair of Geometry with Complex Topology
- 1 January 2011
- Published by Springer Nature
- p. 387-403
Hybrid Approach for Repair of Geometry with Complex Topology
- 5 September 2007
- Published by Elsevier in Mathematics and Computers in Simulation
- Vol. 75 (5-6) , 200-209
Parallel unstructured mesh generation by an advancing front method
- 5 September 2007
- Published by Elsevier in Mathematics and Computers in Simulation
- Vol. 75 (5-6) , 200-209
Parallel unstructured mesh generation by an advancing front method
- 19 September 2005
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 65 (6) , 943-973
Robust generation of high‐quality unstructured meshes on realistic biomedical geometry
In this paper, we propose efficient and robust unstructured mesh generation methods based on computed tomography (CT) and magnetic resonance imaging (MRI) data, in order to obtain a patient‐specific geometry for high‐fidelity numerical simulations. Surface extraction from medical images is carried out mainly using open source libraries, including the Insight Segmentation and Registration Toolkit and the Visualization Toolkit, into the form of facet surface representation. To create high‐quality surface meshes, we propose two approaches. One is a direct advancing front method, and the other is a modified decimation method. The former emphasizes the controllability of local mesh density, and the latter enables semi‐automated mesh generation from low‐quality discrete surfaces. An advancing‐front‐based volume meshing method is employed. Our approaches are demonstrated with high‐fidelity tetrahedral meshes around medical geometries extracted from CT/MRI data. Copyright © 2005 John Wiley & Sons, Ltd.
- 19 September 2005
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 65 (6) , 943-973
Robust generation of high‐quality unstructured meshes on realistic biomedical geometry
In this paper, we propose efficient and robust unstructured mesh generation methods based on computed tomography (CT) and magnetic resonance imaging (MRI) data, in order to obtain a patient‐specific geometry for high‐fidelity numerical simulations. Surface extraction from medical images is carried out mainly using open source libraries, including the Insight Segmentation and Registration Toolkit and the Visualization Toolkit, into the form of facet surface representation. To create high‐quality surface meshes, we propose two approaches. One is a direct advancing front method, and the other is a modified decimation method. The former emphasizes the controllability of local mesh density, and the latter enables semi‐automated mesh generation from low‐quality discrete surfaces. An advancing‐front‐based volume meshing method is employed. Our approaches are demonstrated with high‐fidelity tetrahedral meshes around medical geometries extracted from CT/MRI data. Copyright © 2005 John Wiley & Sons, Ltd.
- 31 May 2005
- Published by Elsevier in Applied Numerical Mathematics
- Vol. 55 (3) , 368-381
Geometry and mesh generation for high fidelity computational simulations using non-uniform rational B-splines
- 31 May 2005
- Published by Elsevier in Applied Numerical Mathematics
- Vol. 55 (3) , 368-381
Geometry and mesh generation for high fidelity computational simulations using non-uniform rational B-splines