A. Roland Ennos
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
A. Roland Ennos has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Adam van Casteren
School of Biological Sciences University of Manchester Manchester UK
3 shared publications - Andrew Peter Dean
Manchester Metropolitan University
1 shared publication - Giles Nicholas Johnson
Department of Earth and Environmental Sciences, Faculty of Science and Engineering, University of Manchester, Manchester, United Kingdom
1 shared publication H. McGhie
Manchester Museum, Oxford Road, Manchester M13 9PL, UK
1 shared publicationJ. W. Hunt
Faculty of Life Sciences, University of Manchester, Jackson's Mill, PO Box 88, Manchester M60 1QD, UK
1 shared publication- James D. Gardiner
Institute of Ageing and Chronic Disease, University of Liverpool, Liverpool, United Kingdom
1 shared publication
Latest Publications
- 16 April 2012
- Published by National Academy of Sciences in Proceedings of the National Academy of Sciences
- Vol. 109 (18) , 6873-6877
Nest-building orangutans demonstrate engineering know-how to produce safe, comfortable beds
Nest-building orangutans must daily build safe and comfortable nest structures in the forest canopy and do this quickly and effectively using the branches that surround them. This study aimed to investigate the mechanical design and architecture of orangutan nests and determine the degree of technical sophistication used in their construction. We measured the whole nest compliance and the thickness of the branches used and recorded the ways in which the branches were fractured. Branch samples were also collected from the nests and subjected to three-point bending tests to determine their mechanical properties. We demonstrated that the center of the nest is more compliant than the edges; this may add extra comfort and safety to the structure. During construction orangutans use the fact that branches only break half-way across in “greenstick” fracture to weave the main nest structure. They choose thicker branches with greater rigidity and strength to build the main structure in this way. They then detach thinner branches by following greenstick fracture with a twisting action to make the lining. These results suggest that orangutans exhibit a degree of technical knowledge and choice in the construction of nests.
- 16 April 2012
- Published by National Academy of Sciences in Proceedings of the National Academy of Sciences
- Vol. 109 (18) , 6873-6877
Nest-building orangutans demonstrate engineering know-how to produce safe, comfortable beds
Nest-building orangutans must daily build safe and comfortable nest structures in the forest canopy and do this quickly and effectively using the branches that surround them. This study aimed to investigate the mechanical design and architecture of orangutan nests and determine the degree of technical sophistication used in their construction. We measured the whole nest compliance and the thickness of the branches used and recorded the ways in which the branches were fractured. Branch samples were also collected from the nests and subjected to three-point bending tests to determine their mechanical properties. We demonstrated that the center of the nest is more compliant than the edges; this may add extra comfort and safety to the structure. During construction orangutans use the fact that branches only break half-way across in “greenstick” fracture to weave the main nest structure. They choose thicker branches with greater rigidity and strength to build the main structure in this way. They then detach thinner branches by following greenstick fracture with a twisting action to make the lining. These results suggest that orangutans exhibit a degree of technical knowledge and choice in the construction of nests.
- Open Access
- 1 May 2010
- Published by The Company of Biologists in Journal of Experimental Biology
- Vol. 213 (9) , 1602-1608
Sonation in the male common snipe (Capella gallinago gallinagoL.) is achieved by a flag-like fluttering of their tail feathers and consequent vortex shedding
Male common snipe (Capella gallinago gallinago) produce a ‘drumming’ sound with their outer tail feathers during their mating dives, but little is known about how this is achieved. We investigated the movements and sound producing capabilities of the outer tail feathers. Using a wind tunnel, we compared observations of the frequencies of sound produced with the predictions from aerodynamic theory. The feathers were also filmed in an air-flow with a high speed video camera, and subjected to morphological examination and biomechanical testing. We propose a mechanistic hypothesis of how the modified outer feathers of the male common snipe generate sound, and the adaptations that facilitate this. Video and audio analysis of the feather demonstrated that a fluttering of the trailing vane generated the sound. The flutter of the vane is facilitated by the rearward curvature of the feather shaft, reduced branching angles of the barbs in the trailing vane and the lack of hooks on the barbs along a hinge region, all of which increase its flexural compliance. Sound production occurred at the same frequency as the vane movements, at frequencies consistent with it being produced by a fluttering flag mechanism powered by vortex shedding.
- 1 May 2010
- Published by The Company of Biologists in Journal of Experimental Biology
- Vol. 213 (9) , 1602-1608
Open AccessSonation in the male common snipe (Capella gallinago gallinagoL.) is achieved by a flag-like fluttering of their tail feathers and consequent vortex shedding
Male common snipe (Capella gallinago gallinago) produce a ‘drumming’ sound with their outer tail feathers during their mating dives, but little is known about how this is achieved. We investigated the movements and sound producing capabilities of the outer tail feathers. Using a wind tunnel, we compared observations of the frequencies of sound produced with the predictions from aerodynamic theory. The feathers were also filmed in an air-flow with a high speed video camera, and subjected to morphological examination and biomechanical testing. We propose a mechanistic hypothesis of how the modified outer feathers of the male common snipe generate sound, and the adaptations that facilitate this. Video and audio analysis of the feather demonstrated that a fluttering of the trailing vane generated the sound. The flutter of the vane is facilitated by the rearward curvature of the feather shaft, reduced branching angles of the barbs in the trailing vane and the lack of hooks on the barbs along a hinge region, all of which increase its flexural compliance. Sound production occurred at the same frequency as the vane movements, at frequencies consistent with it being produced by a fluttering flag mechanism powered by vortex shedding.
- 16 December 2009
- Published by The Royal Society in Proceedings Of The Royal Society B-Biological Sciences
- Vol. 277 (1685) , 1253-1258
Transverse stresses and modes of failure in tree branches and other beams
The longitudinal stresses in beams subjected to bending also set up transverse stresses within them; they compress the cross section when the beam's curvature is being increased and stretch it when its curvature is being reduced. Analysis shows that transverse stresses rise to a maximum at the neutral axis and increase with both the bending moment applied and the curvature of the beam. These stresses can qualitatively explain the fracture behaviour of tree branches. Curved ‘hazard beams’ that are being straightened split down the middle because of the low transverse tensile strength of wood. By contrast, straight branches of light wood buckle when they are bent because of its low transverse compressive strength. Branches of denser wood break, but the low transverse tensile strength diverts the crack longitudinally when the fracture has only run half-way across the beam, to produce their characteristic ‘greenstick fracture’. The bones of young mammals and uniaxially reinforced composite beams may also be prone to greenstick fracture because of their lower transverse tensile strength.
- 16 December 2009
- Published by The Royal Society in Proceedings Of The Royal Society B-Biological Sciences
- Vol. 277 (1685) , 1253-1258
Transverse stresses and modes of failure in tree branches and other beams
The longitudinal stresses in beams subjected to bending also set up transverse stresses within them; they compress the cross section when the beam's curvature is being increased and stretch it when its curvature is being reduced. Analysis shows that transverse stresses rise to a maximum at the neutral axis and increase with both the bending moment applied and the curvature of the beam. These stresses can qualitatively explain the fracture behaviour of tree branches. Curved ‘hazard beams’ that are being straightened split down the middle because of the low transverse tensile strength of wood. By contrast, straight branches of light wood buckle when they are bent because of its low transverse compressive strength. Branches of denser wood break, but the low transverse tensile strength diverts the crack longitudinally when the fracture has only run half-way across the beam, to produce their characteristic ‘greenstick fracture’. The bones of young mammals and uniaxially reinforced composite beams may also be prone to greenstick fracture because of their lower transverse tensile strength.
- Open Access
- 11 August 2008
- Published by Oxford University Press (OUP) in Annals of Botany
- Vol. 102 (4) , 653-656
A Novel Mechanism by which Silica Defends Grasses Against Herbivory
Previous studies have shown that silica in grass leaves defends them against small herbivores, which avoid high-silica grasses and digest them less efficiently. This study tested the idea that silica can reduce digestibility by preventing the mechanical breakdown of chlorenchyma cells. Both the percentage of total chlorophyll liberated from high- and low-silica grass leaves by mechanical grinding and the chlorophyll content of locust faeces were measured. High-silica grasses released less chlorophyll after grinding and retained more after passing through the gut of locusts, showing that silica levels correlated with increased mechanical protection. These results suggest that silica may defend grasses at least in part by reducing mechanical breakdown of the leaf, and that mechanical protection of resources in chlorenchyma cells is a novel and potentially important mechanism by which silica protects grasses.
- 11 August 2008
- Published by Oxford University Press (OUP) in Annals of Botany
- Vol. 102 (4) , 653-656
Open AccessA Novel Mechanism by which Silica Defends Grasses Against Herbivory
Previous studies have shown that silica in grass leaves defends them against small herbivores, which avoid high-silica grasses and digest them less efficiently. This study tested the idea that silica can reduce digestibility by preventing the mechanical breakdown of chlorenchyma cells. Both the percentage of total chlorophyll liberated from high- and low-silica grass leaves by mechanical grinding and the chlorophyll content of locust faeces were measured. High-silica grasses released less chlorophyll after grinding and retained more after passing through the gut of locusts, showing that silica levels correlated with increased mechanical protection. These results suggest that silica may defend grasses at least in part by reducing mechanical breakdown of the leaf, and that mechanical protection of resources in chlorenchyma cells is a novel and potentially important mechanism by which silica protects grasses.
- Open Access
- 7 August 2006
- Published by Oxford University Press (OUP) in Journal of Experimental Botany
- Vol. 57 (12) , 3123-3130
Structural development and stability of rice Oryza sativa L. var. Nerica 1
The structural development of glasshouse-grown rice Oryza sativa L. var. Nerica 1 was studied in relation to its stability against lodging. The morphology and mechanical properties of both the stem and roots were examined from tillering, 4 weeks after transplantation up to maturity, together with plant weight distribution and anchorage strength. The ‘factors of safety’ against root and stem failure were subsequently calculated throughout development. Rice plants showed similar morphology to wheat, although they possessed around twice as many tillers per plant and 10 times as many coronal roots. The mechanics of anchorage were also similar. The strength and rigidity of individual tillers increased throughout development as the plants grew taller and heavier and were around 15 times greater than in wheat. By contrast, individual root bending strength, the number of roots, and the anchorage strength levelled off earlier, and anchorage strength was only around twice that in wheat. Consequently, while the self-weight safety factor against stem failure was much higher than in wheat, increasing until late on in development from around 30 to 150, the self-weight safety factor against root anchorage failure was similar to wheat, decreasing from around 15 to 5. Consequently, plants subjected to anchorage tests always failed in their root system rather than their shoot system. The results suggest that, in the field, rice plants would be more likely to undergo root lodging than stem lodging, and that breeding efforts to reduce the incidence of lodging should act to strengthen the rather weak coronal roots.
- 7 August 2006
- Published by Oxford University Press (OUP) in Journal of Experimental Botany
- Vol. 57 (12) , 3123-3130
Open AccessStructural development and stability of rice Oryza sativa L. var. Nerica 1
The structural development of glasshouse-grown rice Oryza sativa L. var. Nerica 1 was studied in relation to its stability against lodging. The morphology and mechanical properties of both the stem and roots were examined from tillering, 4 weeks after transplantation up to maturity, together with plant weight distribution and anchorage strength. The ‘factors of safety’ against root and stem failure were subsequently calculated throughout development. Rice plants showed similar morphology to wheat, although they possessed around twice as many tillers per plant and 10 times as many coronal roots. The mechanics of anchorage were also similar. The strength and rigidity of individual tillers increased throughout development as the plants grew taller and heavier and were around 15 times greater than in wheat. By contrast, individual root bending strength, the number of roots, and the anchorage strength levelled off earlier, and anchorage strength was only around twice that in wheat. Consequently, while the self-weight safety factor against stem failure was much higher than in wheat, increasing until late on in development from around 30 to 150, the self-weight safety factor against root anchorage failure was similar to wheat, decreasing from around 15 to 5. Consequently, plants subjected to anchorage tests always failed in their root system rather than their shoot system. The results suggest that, in the field, rice plants would be more likely to undergo root lodging than stem lodging, and that breeding efforts to reduce the incidence of lodging should act to strengthen the rather weak coronal roots.
- Open Access
- 1 December 2005
- Published by The Company of Biologists in Journal of Experimental Biology
- Vol. 208 (23) , 4523-4527
Flight behaviour during foraging of the social waspVespula vulgaris(Hymenoptera: Vespidae) and four mimetic hoverflies (Diptera:Syrphidae)Sericomyia silentis,Myathropa florea,Helophilussp. andSyrphussp.
Many hoverfly species show specific or non specific morphological resemblance to wasps (Vespula sp.) and it has been suggested that they also show similar flight behaviour. In this study we therefore compared the flight behaviour of wasps with that of four mimetic hoverflies, Sericomyia silentis, Myathropa florea, Helophilus sp. and Syrphus sp., by filming insects while they were foraging on an artificial array of flowers. Films were analysed to determine the routes taken, time spent hovering and flight speed. Of the four flies, only the non specific mimic, Syrphus, showed similar flight behaviour to the wasps; it flew more slowly, and with more roundabout routes than the other flies, hesitating before landing. These results suggest that in hoverflies there is little reason to expect strict correlation between morphological and behavioural mimicry; insects may acquire the similarities to their model more-or-less independently.
- 1 December 2005
- Published by The Company of Biologists in Journal of Experimental Biology
- Vol. 208 (23) , 4523-4527
Open AccessFlight behaviour during foraging of the social waspVespula vulgaris(Hymenoptera: Vespidae) and four mimetic hoverflies (Diptera:Syrphidae)Sericomyia silentis,Myathropa florea,Helophilussp. andSyrphussp.
Many hoverfly species show specific or non specific morphological resemblance to wasps (Vespula sp.) and it has been suggested that they also show similar flight behaviour. In this study we therefore compared the flight behaviour of wasps with that of four mimetic hoverflies, Sericomyia silentis, Myathropa florea, Helophilus sp. and Syrphus sp., by filming insects while they were foraging on an artificial array of flowers. Films were analysed to determine the routes taken, time spent hovering and flight speed. Of the four flies, only the non specific mimic, Syrphus, showed similar flight behaviour to the wasps; it flew more slowly, and with more roundabout routes than the other flies, hesitating before landing. These results suggest that in hoverflies there is little reason to expect strict correlation between morphological and behavioural mimicry; insects may acquire the similarities to their model more-or-less independently.