Gordon Moore
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Gordon Moore has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Sudarshan Mehta
University of Calgary
6 shared publications - Matthew Ursenbach
Department of Chemical and Petroleum Engineering, Schulich School of Engineering, University of Calgary, Calgary, AB T2N 1N4, Canada
3 shared publications - Alexey Cheremisin
Skolkovo Institute of Science and Technology, Moscow 143026, Russia
2 shared publications - Donald Mallory
Department of Chemical and Petroleum Engineering, Schulich School of Engineering, University of Calgary, Calgary, AB T2N 1N4, Canada
2 shared publications E. Zalewski
University of Calgary
2 shared publicationsM.G. Ursenbach
University of Calgary
2 shared publications
Latest Publications
- Open Access
- 13 October 2024
- Published by MDPI AG in Geosciences
- Vol. 14 (10) , 270
New Insights into the Understanding of High-Pressure Air Injection (HPAI): The Role of the Different Chemical Reactions
High-pressure air injection (HPAI) is an enhanced oil recovery process in which compressed air is injected into deep, light oil reservoirs, with the expectation that the oxygen in the injected air will react with a fraction of the reservoir oil at an elevated temperature to produce carbon dioxide. The different chemical reactions taking place can be grouped into oxygen addition, thermal cracking, oxygen-induced cracking, and bond scission reactions. The latter reactions involve the combustion of a flammable vapor as well as the combustion of solid fuel, commonly known as “coke”. Since stable peak temperatures observed during HPAI experiments are typically below 300 °C, it has been suggested that thermal cracking and combustion of solid fuel may not be important reaction mechanisms for the process. The objective of this work is to assess the validity of that hypothesis. Therefore, this study makes use of different oxidation and combustion HPAI experiments, which were performed on two different light oil reservoir samples. Modeling of those tests indicate that thermal cracking is not an important reaction mechanism during HPAI and can potentially be ignored. The work also suggests that the main fuel consumed by the process is a flammable vapor generated by the chemical reactions. This represents a shift from the original in situ combustion paradigm, which is based on the combustion of coke.
- 13 October 2024
- Published by MDPI AG in Geosciences
- Vol. 14 (10) , 270
Open AccessNew Insights into the Understanding of High-Pressure Air Injection (HPAI): The Role of the Different Chemical Reactions
High-pressure air injection (HPAI) is an enhanced oil recovery process in which compressed air is injected into deep, light oil reservoirs, with the expectation that the oxygen in the injected air will react with a fraction of the reservoir oil at an elevated temperature to produce carbon dioxide. The different chemical reactions taking place can be grouped into oxygen addition, thermal cracking, oxygen-induced cracking, and bond scission reactions. The latter reactions involve the combustion of a flammable vapor as well as the combustion of solid fuel, commonly known as “coke”. Since stable peak temperatures observed during HPAI experiments are typically below 300 °C, it has been suggested that thermal cracking and combustion of solid fuel may not be important reaction mechanisms for the process. The objective of this work is to assess the validity of that hypothesis. Therefore, this study makes use of different oxidation and combustion HPAI experiments, which were performed on two different light oil reservoir samples. Modeling of those tests indicate that thermal cracking is not an important reaction mechanism during HPAI and can potentially be ignored. The work also suggests that the main fuel consumed by the process is a flammable vapor generated by the chemical reactions. This represents a shift from the original in situ combustion paradigm, which is based on the combustion of coke.
- Open Access
In Situ Combustion of Heavy Oil within a Vuggy Carbonate Reservoir: Part I—Feasibility Study
Worldwide, the known recoverable heavy oil and bitumen reserves make up more than 64% of the total reserves, of which more than 60% are trapped in carbonates. Air injection has immense potential for hydrocarbon recovery from various reservoirs. While most of the successful air-based techniques are performed within carbonate reservoirs containing light oil, theoretically, in situ combustion (ISC) has also shown great potential for recovering heavy oil and bitumen. Carbonates are complex in terms of geology and are often associated with fractures and vugs that affect the fluid flow, pressure propagation and progression of the ISC reactions. This paper describes the first experiment in which the triple-porosity concept was applied to simulate heterogeneity through artificially induced vugs, core matrix and fractures. This approach was used to study the feasibility of the ISC recovery technique for heavy oil (14° API) within a dolomite reservoir using a combustion tube (CT) in an experiment performed at 1740 psig. The combustion front advanced through 78% of the core length prior to the termination of air injection, producing 80% of the initial oil. To differentiate between the various sources of the CO2 gas (a product of carbonate decomposition vs. the combustion reaction) the atomic ratios of (CO2 + CO)/CO = 6 and (CO2 + CO)/N2 = 0.21 were applied. Additionally, partial upgrading of the produced heavy oil was observed.
Open AccessIn Situ Combustion of Heavy Oil within a Vuggy Carbonate Reservoir: Part I—Feasibility Study
Worldwide, the known recoverable heavy oil and bitumen reserves make up more than 64% of the total reserves, of which more than 60% are trapped in carbonates. Air injection has immense potential for hydrocarbon recovery from various reservoirs. While most of the successful air-based techniques are performed within carbonate reservoirs containing light oil, theoretically, in situ combustion (ISC) has also shown great potential for recovering heavy oil and bitumen. Carbonates are complex in terms of geology and are often associated with fractures and vugs that affect the fluid flow, pressure propagation and progression of the ISC reactions. This paper describes the first experiment in which the triple-porosity concept was applied to simulate heterogeneity through artificially induced vugs, core matrix and fractures. This approach was used to study the feasibility of the ISC recovery technique for heavy oil (14° API) within a dolomite reservoir using a combustion tube (CT) in an experiment performed at 1740 psig. The combustion front advanced through 78% of the core length prior to the termination of air injection, producing 80% of the initial oil. To differentiate between the various sources of the CO2 gas (a product of carbonate decomposition vs. the combustion reaction) the atomic ratios of (CO2 + CO)/CO = 6 and (CO2 + CO)/N2 = 0.21 were applied. Additionally, partial upgrading of the produced heavy oil was observed.
- Open Access
Experimental Investigations of Forward and Reverse Combustion for Increasing Oil Recovery of a Real Oil Field
The work presented herein is devoted to a unique set of forward and reverse combustion tube (CT) experiments to access the suitability and potential of the in situ combustion (ISC) method for the light oil carbonate reservoir. One forward and one reverse combustion tube tests were carried out using the high-pressure combustion tube (HPCT) experimental setup. However, during reverse combustion, the front moved in the opposite direction to the airflow. The results obtained from experiments such as fuel/air requirements, H/C ratio, and recovery efficiency are crucial for further validation of the numerical model. A quantitative assessment of the potential for the combustion was carried out. The oil recovery of forward combustion was as high as 91.4% of the initial oil in place, while that for the reverse combustion test demonstrated a 43% recovery. In the given conditions, forward combustion demonstrated significantly higher efficiency. However, the stabilized combustion front propagation and produced gases of reverse combustion prove its possible applicability. Currently, there is a limited amount of available studies on reverse combustion and a lack of publications within the last decades despite advances in technologies. However, reverse combustion might have advantages over forward combustion for heavy oil reservoirs with lower permeability or might serve as a reservoir preheating technique. These experiments give the opportunity to build and validate the numerical models of forward and reverse combustion conducted at reservoir conditions and test their field application using different scenarios.
Open AccessExperimental Investigations of Forward and Reverse Combustion for Increasing Oil Recovery of a Real Oil Field
The work presented herein is devoted to a unique set of forward and reverse combustion tube (CT) experiments to access the suitability and potential of the in situ combustion (ISC) method for the light oil carbonate reservoir. One forward and one reverse combustion tube tests were carried out using the high-pressure combustion tube (HPCT) experimental setup. However, during reverse combustion, the front moved in the opposite direction to the airflow. The results obtained from experiments such as fuel/air requirements, H/C ratio, and recovery efficiency are crucial for further validation of the numerical model. A quantitative assessment of the potential for the combustion was carried out. The oil recovery of forward combustion was as high as 91.4% of the initial oil in place, while that for the reverse combustion test demonstrated a 43% recovery. In the given conditions, forward combustion demonstrated significantly higher efficiency. However, the stabilized combustion front propagation and produced gases of reverse combustion prove its possible applicability. Currently, there is a limited amount of available studies on reverse combustion and a lack of publications within the last decades despite advances in technologies. However, reverse combustion might have advantages over forward combustion for heavy oil reservoirs with lower permeability or might serve as a reservoir preheating technique. These experiments give the opportunity to build and validate the numerical models of forward and reverse combustion conducted at reservoir conditions and test their field application using different scenarios.
- 1 January 2008
- Published by Society of Petroleum Engineers (SPE) in Journal of Canadian Petroleum Technology
- Vol. 47 (1)
Heats of Combustion of Selected Crude Oils and Their SARA Fractions
In situ combustion and high-pressure air injection are enhanced oil recovery (EOR) processes used to recover oil from both heavy and light oil reservoirs. These processes are quite complex and involve consideration of heat and mass transfer, phase behaviour of oil, water and gas, as well as relative permeability effects. This paper outlines a study that was conducted in order to develop a better understanding of the heats of combustion (HOC) for three different types of crude oils and their respective saturate, aromatic, resin and asphaltene (SARA) fractions. One outcome of the study indicated that saturates and aromatics have higher heating values than resins and asphaltenes, where this value in both saturates and aromatics (in any given crude oil) is close. Resins and asphaltenes also displayed heating values that were almost the same, however, were consistent in having a lower heating value than saturates and aromatics. The linear mixing rule was applied to predict the heat of combustion for the three crude oils studied. The HOCs for the maltene and asphaltene fractions were mathematically combined (per the mixing rule) to predict the actual observed HOC of the combined maltene/asphaltene crude. This rule did not hold true for all the crude oils studied, however, which suggests that the heat of combustion is not necessarily independent of the presence of other fractions. Introduction In situ combustion and high pressure air injection are technologies used for the recovery of both heavy and light crude oils. These technologies involve the creation of an oxidation front in the reservoir with subsequent propagation by air injection. Generally, air is injected in the reservoir and the oxygen contained in the air reacts with the oil through various oxidation reactions. The burning front is formed and the combustion gases produced from these reactions are available to help displace the oil. This process offers economic and technical opportunities for improved oil recovery in many reservoirs. Many thermal analysis studies on both light and heavy crude oils have been conducted and several oxidation tests for modelling the process have been performed. Verkoczy and Freitag(1) applied the relevance of various oxidation reactions to the modelling of in situ combustion in heavy oils, through three different sets of experiments. They performed thermogravimetric scans and autoclave tests on three heavy oils and their SARA fractions. They found that low temperature oxidation had significant and sometimes dramatic effects on the amount of coke formation. They also found that asphaltenes apparently underwent low temperature oxidation more rapidly than other crude fractions. K?k et al.(2) used thermogravimetric analysis under an air atmosphere at a 10 °C/min heating rate. Two oils (medium and heavy) were separated into their SARA fractions. Then a quantitative investigation was performed in order to determine the temperature intervals at which evaporation, oxidation and combustion effects operated for each fraction. Kinetic parameters of SARA fractions according to the Coat and Redfern technique were also established. K?k and Karacan(3) studied the behaviour and effect of SARA fractions of two different oils during combustion using a thermogravimetric analyzer and a differential scanning calorimeter.
- 1 January 2008
- Published by Society of Petroleum Engineers (SPE) in Journal of Canadian Petroleum Technology
- Vol. 47 (1)
Heats of Combustion of Selected Crude Oils and Their SARA Fractions
In situ combustion and high-pressure air injection are enhanced oil recovery (EOR) processes used to recover oil from both heavy and light oil reservoirs. These processes are quite complex and involve consideration of heat and mass transfer, phase behaviour of oil, water and gas, as well as relative permeability effects. This paper outlines a study that was conducted in order to develop a better understanding of the heats of combustion (HOC) for three different types of crude oils and their respective saturate, aromatic, resin and asphaltene (SARA) fractions. One outcome of the study indicated that saturates and aromatics have higher heating values than resins and asphaltenes, where this value in both saturates and aromatics (in any given crude oil) is close. Resins and asphaltenes also displayed heating values that were almost the same, however, were consistent in having a lower heating value than saturates and aromatics. The linear mixing rule was applied to predict the heat of combustion for the three crude oils studied. The HOCs for the maltene and asphaltene fractions were mathematically combined (per the mixing rule) to predict the actual observed HOC of the combined maltene/asphaltene crude. This rule did not hold true for all the crude oils studied, however, which suggests that the heat of combustion is not necessarily independent of the presence of other fractions. Introduction In situ combustion and high pressure air injection are technologies used for the recovery of both heavy and light crude oils. These technologies involve the creation of an oxidation front in the reservoir with subsequent propagation by air injection. Generally, air is injected in the reservoir and the oxygen contained in the air reacts with the oil through various oxidation reactions. The burning front is formed and the combustion gases produced from these reactions are available to help displace the oil. This process offers economic and technical opportunities for improved oil recovery in many reservoirs. Many thermal analysis studies on both light and heavy crude oils have been conducted and several oxidation tests for modelling the process have been performed. Verkoczy and Freitag(1) applied the relevance of various oxidation reactions to the modelling of in situ combustion in heavy oils, through three different sets of experiments. They performed thermogravimetric scans and autoclave tests on three heavy oils and their SARA fractions. They found that low temperature oxidation had significant and sometimes dramatic effects on the amount of coke formation. They also found that asphaltenes apparently underwent low temperature oxidation more rapidly than other crude fractions. K?k et al.(2) used thermogravimetric analysis under an air atmosphere at a 10 °C/min heating rate. Two oils (medium and heavy) were separated into their SARA fractions. Then a quantitative investigation was performed in order to determine the temperature intervals at which evaporation, oxidation and combustion effects operated for each fraction. Kinetic parameters of SARA fractions according to the Coat and Redfern technique were also established. K?k and Karacan(3) studied the behaviour and effect of SARA fractions of two different oils during combustion using a thermogravimetric analyzer and a differential scanning calorimeter.
- 1 October 2007
- Published by American Society of Civil Engineers (ASCE) in Practice Periodical of Hazardous, Toxic, and Radioactive Waste Management
- Vol. 11 (4) , 259-267
Kinetic Model for the Remediation of Soils Contaminated with Hydrocarbons Using Low-Temperature Oxidation
This paper presents a kinetic model for the remediation of soils contaminated with hydrocarbons by low-temperature oxidation (LTO). The oxidation of hydrocarbons, which consist of a mixture of straight chained, branched and ringed compounds follow a number of complex chain reactions. The investigations into the kinetics of the process are simplified by using pseudocomponents such as maltenes, asphaltenes, and coke. The mechanisms of LTO are divided into four groups: Original maltenes comprised of slow-reacting and volatile maltenes. Slow-reacting maltenes react with oxygen to produce asphaltenes and water. Asphaltenes undergo polymerization and dehydrogenation to form coke, product-volatile maltenes, and hydrogen; the volatile maltenes oxidize to form carbon oxides and water. These proposed mechanisms explain the experimental observations. The kinetic model in conjunction with a heat-transfer model can be used to determine the compositional changes when LTO is applied to remediate soils contaminated with hydrocarbons.
- 1 October 2007
- Published by American Society of Civil Engineers (ASCE) in Practice Periodical of Hazardous, Toxic, and Radioactive Waste Management
- Vol. 11 (4) , 259-267
Kinetic Model for the Remediation of Soils Contaminated with Hydrocarbons Using Low-Temperature Oxidation
This paper presents a kinetic model for the remediation of soils contaminated with hydrocarbons by low-temperature oxidation (LTO). The oxidation of hydrocarbons, which consist of a mixture of straight chained, branched and ringed compounds follow a number of complex chain reactions. The investigations into the kinetics of the process are simplified by using pseudocomponents such as maltenes, asphaltenes, and coke. The mechanisms of LTO are divided into four groups: Original maltenes comprised of slow-reacting and volatile maltenes. Slow-reacting maltenes react with oxygen to produce asphaltenes and water. Asphaltenes undergo polymerization and dehydrogenation to form coke, product-volatile maltenes, and hydrogen; the volatile maltenes oxidize to form carbon oxides and water. These proposed mechanisms explain the experimental observations. The kinetic model in conjunction with a heat-transfer model can be used to determine the compositional changes when LTO is applied to remediate soils contaminated with hydrocarbons.
- 1 February 2007
- Published by Society of Petroleum Engineers (SPE) in Journal of Canadian Petroleum Technology
- Vol. 46 (2)
Phase Behaviour and Compositional Changes Associated With Residual Oxygen in a Miscible CO/Light Oil Reservoir
Concern about the effects of global greenhouse gases has made people aware of the need to reduce the atmospheric concentration of industrial waste gas. Alberta, as the centre of Canada's petroleum industry, is strongly impacted by the politics of greenhouse gases. One way Alberta can achieve the goals of the Kyoto Protocol is to capture CO2 from stack gases and to inject it into oil reservoirs to enhance recovery while sequestering at least a portion of the CO2. This paper will concentrate on oil from the Swan Hills Formation reservoir operated by Devon Oil Corporation. The phase behaviour of different concentrations of CO2/O2 mixtures injected into the Swan Hills reservoir was investigated. Two PVT (Pressure-Volume-Temperature) apparatus were used to visually observe phases and to determine bubble points and swelling of the oil rich phase. The PVT measurements were performed to develop a basic understanding of the phase behaviour for the CO2 / O2 /oil system. The composition of oxidized oil was predicted using a previously developed low temperature oxidation model coupled with phase equilibrium calculations. Introduction Carbon dioxide flooding is a well established enhanced oil recovery process in regions where CO2 is available. Canada has been slow to implement CO2 floods due to the lack of natural sources. However, the public's concern with greenhouse gas emissions and Canada's support for the Kyoto Protocol provide sufficient environmental incentives to allow for the application of CO2 floodingas a combined EOR/sequestration process. Capturing the CO2 from stack gas is an expensive process and the actual cost will depend on the purity of the CO2 stream that is required. Oxygen is an important factor as its impurity can modify the native oil properties through low temperature oxidation reactions, promotion of corrosion in the injection and production piping and alter the phase behaviour of the reservoir fluids. The study described in this paper will examine how oxygen is consumed in the reservoir, and it will concentrate on the impact of oxidation reactions with regard to the composition and emulsification characteristics of the oil. Lee(1) studied the phase behaviour and displacement efficiency of a carbon dioxide-hydrocarbon system which consisted of various mixtures of n-pentane/n-hexane. The results demonstrated that multiple phase behaviour involving two liquids with and without a vapour phase occurred during carbon dioxide injection in low temperature reservoirs. A number of studies on the effectiveness of carbon dioxide displacement under miscible and immiscible conditions have been reported by Wilburn et al.(2), Dyer et al.(3), Srivastava and Huang(4, 5) and Srivastava et.al.(6). The results showed that CO2 /oil miscibility could be developed and that the swelling behaviour depended on the chemical composition of the oil. Wilburn et al.(2) also found that miscibility is strongly dependent on the volatility or boiling point distribution of the oil. Dyer et al.(3) investigated the phase behaviour of typical Saskatchewan heavy oils with carbon dioxide. Their study was divided into two categories: stock tank oil and reservoir oil, which were mixed with CO2 in different ratios. Parameters studied included viscosity, density, swelling factor and gas-oil ratio (GOR).
- 1 February 2007
- Published by Society of Petroleum Engineers (SPE) in Journal of Canadian Petroleum Technology
- Vol. 46 (2)
Phase Behaviour and Compositional Changes Associated With Residual Oxygen in a Miscible CO/Light Oil Reservoir
Concern about the effects of global greenhouse gases has made people aware of the need to reduce the atmospheric concentration of industrial waste gas. Alberta, as the centre of Canada's petroleum industry, is strongly impacted by the politics of greenhouse gases. One way Alberta can achieve the goals of the Kyoto Protocol is to capture CO2 from stack gases and to inject it into oil reservoirs to enhance recovery while sequestering at least a portion of the CO2. This paper will concentrate on oil from the Swan Hills Formation reservoir operated by Devon Oil Corporation. The phase behaviour of different concentrations of CO2/O2 mixtures injected into the Swan Hills reservoir was investigated. Two PVT (Pressure-Volume-Temperature) apparatus were used to visually observe phases and to determine bubble points and swelling of the oil rich phase. The PVT measurements were performed to develop a basic understanding of the phase behaviour for the CO2 / O2 /oil system. The composition of oxidized oil was predicted using a previously developed low temperature oxidation model coupled with phase equilibrium calculations. Introduction Carbon dioxide flooding is a well established enhanced oil recovery process in regions where CO2 is available. Canada has been slow to implement CO2 floods due to the lack of natural sources. However, the public's concern with greenhouse gas emissions and Canada's support for the Kyoto Protocol provide sufficient environmental incentives to allow for the application of CO2 floodingas a combined EOR/sequestration process. Capturing the CO2 from stack gas is an expensive process and the actual cost will depend on the purity of the CO2 stream that is required. Oxygen is an important factor as its impurity can modify the native oil properties through low temperature oxidation reactions, promotion of corrosion in the injection and production piping and alter the phase behaviour of the reservoir fluids. The study described in this paper will examine how oxygen is consumed in the reservoir, and it will concentrate on the impact of oxidation reactions with regard to the composition and emulsification characteristics of the oil. Lee(1) studied the phase behaviour and displacement efficiency of a carbon dioxide-hydrocarbon system which consisted of various mixtures of n-pentane/n-hexane. The results demonstrated that multiple phase behaviour involving two liquids with and without a vapour phase occurred during carbon dioxide injection in low temperature reservoirs. A number of studies on the effectiveness of carbon dioxide displacement under miscible and immiscible conditions have been reported by Wilburn et al.(2), Dyer et al.(3), Srivastava and Huang(4, 5) and Srivastava et.al.(6). The results showed that CO2 /oil miscibility could be developed and that the swelling behaviour depended on the chemical composition of the oil. Wilburn et al.(2) also found that miscibility is strongly dependent on the volatility or boiling point distribution of the oil. Dyer et al.(3) investigated the phase behaviour of typical Saskatchewan heavy oils with carbon dioxide. Their study was divided into two categories: stock tank oil and reservoir oil, which were mixed with CO2 in different ratios. Parameters studied included viscosity, density, swelling factor and gas-oil ratio (GOR).
- 1 April 2006
- Published by Society of Petroleum Engineers (SPE) in Journal of Canadian Petroleum Technology
- Vol. 45 (4)
Oxidation Studies of Light Hydrocarbons for Underbalanced Drilling Safety
Economic development of many of the world's oil and gas reserves will require the application of improved drilling methods such as underbalanced drilling (UBD), a technique used to minimize formation damage in hydrocarbon reservoirs. In UBD operations, oxygen-reduced air is often injected along with an oil-based drilling fluid. This oxygen-reduced air may contain up to 5% oxygen which can react with oil and/or an oil-based drilling fluid during the drilling process to form potentially hazardous oxidized hydrocarbons. This could lead to the presence of potentially flammable or explosive mixtures in the surface piping and/or drill string, particularly the return annulus. Discussion of the oxidation behaviour of light oils and oil-based drilling fluids in the literature is limited, particularly regarding the effects of long-term exposure to oxygen. This paper characterizes the oxidation behaviour of two light oils and an oil-based drilling fluid using thermogravimetry (TG) and differential scanning calorimetry at 89 and 9,811 kPa (1,410 psig). The effects of core, pressure, and pre-exposure to oxygen on subsequent oxidation behaviour were studied. The results show that the addition of crushed core enhanced the oxidation reactions of the oil samples and delayed exothermic activity of the drilling fluid. Elevated pressure accelerated the oxidation reactions. Pre-exposure to oxygen was shown to increase the reactivity of the oils and drilling fluid during subsequent oxidation. The results indicate that under certain conditions, oxidation processes could begin at significantly reduced temperatures, possibly leading to ignition of the hydrocarbon mixtures. Introduction Underbalanced drilling is a technique used to minimize formation damage caused by drilling fluid invasion in hydrocarbon reservoirs. In order to achieve this technique, the hydrostatic head of liquid in the hole must be decreased, which can be accomplished by co-injecting nitrogen, natural gas, flue gas, vitiated air (air mixed with nitrogen), or oxygen-reduced air (air with some of the oxygen removed). The oxygen containing gases are the least expensive, but the possibility of flammable or explosive mixtures is an important safety consideration. Oxygen-reduced air is normally obtained using portable membrane separation systems but often still contains up to 5% oxygen by volume. During the drilling process, this oxygen can react with produced hydrocarbons or the oil-based drilling fluid to form peroxides and other oxidized hydrocarbons. These oxidized hydrocarbons could pose a safety hazard. While the oxygen concentrations under consideration are relatively small, the pressures and temperatures in the reservoir and along the drill string are significant. Added to this is the effect of prolonged exposure to oxygen. Drilling fluid is re-circulated throughout the drilling operation and may be used in multiple operations. It may also be exposed to oxygen while in the drilling mud tanks at the surface (during the drilling operation) and in storage tanks. Over time, the fluid may be gradually oxidized, posing an increased risk of combustion or even explosion. Due to the serious ramifications of undesired oxidation processes, it is necessary to establish fundamental information on the oxidation behaviour of the hydrocarbons involved in these processes.
- 1 April 2006
- Published by Society of Petroleum Engineers (SPE) in Journal of Canadian Petroleum Technology
- Vol. 45 (4)
Oxidation Studies of Light Hydrocarbons for Underbalanced Drilling Safety
Economic development of many of the world's oil and gas reserves will require the application of improved drilling methods such as underbalanced drilling (UBD), a technique used to minimize formation damage in hydrocarbon reservoirs. In UBD operations, oxygen-reduced air is often injected along with an oil-based drilling fluid. This oxygen-reduced air may contain up to 5% oxygen which can react with oil and/or an oil-based drilling fluid during the drilling process to form potentially hazardous oxidized hydrocarbons. This could lead to the presence of potentially flammable or explosive mixtures in the surface piping and/or drill string, particularly the return annulus. Discussion of the oxidation behaviour of light oils and oil-based drilling fluids in the literature is limited, particularly regarding the effects of long-term exposure to oxygen. This paper characterizes the oxidation behaviour of two light oils and an oil-based drilling fluid using thermogravimetry (TG) and differential scanning calorimetry at 89 and 9,811 kPa (1,410 psig). The effects of core, pressure, and pre-exposure to oxygen on subsequent oxidation behaviour were studied. The results show that the addition of crushed core enhanced the oxidation reactions of the oil samples and delayed exothermic activity of the drilling fluid. Elevated pressure accelerated the oxidation reactions. Pre-exposure to oxygen was shown to increase the reactivity of the oils and drilling fluid during subsequent oxidation. The results indicate that under certain conditions, oxidation processes could begin at significantly reduced temperatures, possibly leading to ignition of the hydrocarbon mixtures. Introduction Underbalanced drilling is a technique used to minimize formation damage caused by drilling fluid invasion in hydrocarbon reservoirs. In order to achieve this technique, the hydrostatic head of liquid in the hole must be decreased, which can be accomplished by co-injecting nitrogen, natural gas, flue gas, vitiated air (air mixed with nitrogen), or oxygen-reduced air (air with some of the oxygen removed). The oxygen containing gases are the least expensive, but the possibility of flammable or explosive mixtures is an important safety consideration. Oxygen-reduced air is normally obtained using portable membrane separation systems but often still contains up to 5% oxygen by volume. During the drilling process, this oxygen can react with produced hydrocarbons or the oil-based drilling fluid to form peroxides and other oxidized hydrocarbons. These oxidized hydrocarbons could pose a safety hazard. While the oxygen concentrations under consideration are relatively small, the pressures and temperatures in the reservoir and along the drill string are significant. Added to this is the effect of prolonged exposure to oxygen. Drilling fluid is re-circulated throughout the drilling operation and may be used in multiple operations. It may also be exposed to oxygen while in the drilling mud tanks at the surface (during the drilling operation) and in storage tanks. Over time, the fluid may be gradually oxidized, posing an increased risk of combustion or even explosion. Due to the serious ramifications of undesired oxidation processes, it is necessary to establish fundamental information on the oxidation behaviour of the hydrocarbons involved in these processes.