TSTom Schanz

Tom Schanz

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Tom Schanz has a total of 61 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Soil–water characteristic curve of unsaturated collapsible soils

    by Qasim A. Al-Obaidi, Tom Schanz

    Collapsible soils are almost found in unsaturated states and involved significant engineering problems. Geotechnical challenges of such soils are represented by the hydro-mechanical behaviour during wetting–drying cycles due to the humidity and climate conditions. The main objective of this paper is to investigate the soil–water characteristic curve (SWCC) of unsaturated collapsible soils. In this study, three types of collapsible soils were investigated such as natural soils of sandy gypseous, silty loess, and artificial soil of gypsum–sand mixture. Determination of soil–water characteristic curve represented by wetting and drying paths has been done using a combination of the axis-translation technique ( i.e . pressure plate device) and vapour equilibrium technique ( i.e . salts solution desiccators) to cover a wide range of applied suction. The test results show that the air-entry value for all soils occurs at a very low suction range. At the boundary effect zone, the coarse grain size of the soil mass cannot hold the water molecules in the pore space, even with a low value of imposed suction. Moreover, the amount of hysteresis varied based on the geological formation and homogeneity of the soil fabric. Furthermore, SWCC has been interpreted by insignificant volume change and a slight reduction in void ratio, especially at high applied suction.


  • Adaptive Constitutive Soil Modeling Concept in Mechanized Tunneling Simulation

    by Arash Alimardani Lavasan, Chenyang Zhao, Tom Schanz

    This paper proposes an innovative concept of adaptive constitutive soil modeling to optimize the complexity of the numerical simulation of shield tunneling. This concept involves the use of an adequate constitutive model for soil, in accordance with mechanical incidents in the domain, to reduce the number of complex soil parameters and computational costs, focusing on the accuracy of numerical predictions. In such an approach, adequate soil investigation can be scheduled by designing a limited number of sophisticated laboratory tests at certain locations, while the rest of the domain can be explored with basic conventional laboratory tests to identify ordinary soil parameters. This concept leads to obtaining adequate and dominant soil parameters at each depth to accurately simulate the phenomenological aspects of soil behavior and soil–tunnel boring machine (TBM)–tunnel interactions without inducing inadmissible uncertainty in terms of advanced soil parameters for unaffected zones. The numerical model accounts for such constructional components face support, grouting in the annular gap, and lining installation. The numerical model responses are studied through the investigation of the evolution of the ground subsidence, as well as soil stresses and lining forces. The behavior of the soil is assumed to be described by a family of hierarchical elastic–plastic constitutive models based on Mohr-Coulomb failure theory. In addition, the size of the target zone where the model adaption should be conducted is studied while its influences on model responses are addressed. Finally, the contribution of the proposed solution to reduce the uncertainty of the numerical predictions is evaluated.


  • Open Access

    Volume change behavior of bentonite-sand mixture under constant suction condition

    by Yasir Al-Badran, Tom Schanz

    The unsaturated state of soil can raise many geotechnical problems upon wetting-drying cycles such as volume change resulting in collapse or swell, change in the shear strength, and change in the hydraulic conductivity. The classical principles of soil mechanics for saturated soil are often not suitable for explaining these phenomena. An experimental work was carried out to study the volume change behavior of Bentonite-Sand mixture under constant suction condition. A mixture of 30% Calcigel bentonite and 70 % Haider sand (30B) were tested in this study. The applied suction was kept constant through the tests. Thirteen 30B specimens were tested under constant suction condition. Two different initial states (slurry and loose) were chosen to examine the effect of initial state on the volume change at unsaturated state. The results of first group (initially slurry state) show that once the suction was applied the compressibility of the specimens in this group followed the isotropic NCL up to 255 kPa suction. Subsequently, the slope of compression curve decreased. The results of increasing suction for initially slurry state show that the slope of compression lines became near to zero for suction higher than 600 kPa. Moreover, when applied suction is lower than the air-entry value, saev, the soil behaviors as the saturated soil. Therefore, the effective stress equation can be applied. The results of second group (initially loose state) show that the unsaturated preconsolidation pressure increases as the constant suction increases. The slopes of the unsaturated over consolidated paths in all tests were closed to the slope of saturated over consolidated path (Cr), while the slopes of the unsaturated normal consolidated (yield) state are higher than the slope of saturated NCL. Finally the results show that the slope of the unsaturated NCL is higher (steeper) than the slope of saturated NCL.

  • Bearing Capacity of Interfering Strip Footings

    by Arash Alimardani Lavasan, Mahmoud Ghazavi, Achim von Blumenthal, Tom Schanz

    In this paper, the ultimate bearing capacity of two closely spaced rigid strip footings with rough base on granular soil is examined based on enhanced limit equilibrium, plastic limit analyses, and finite-difference solutions. The enhanced limit equilibrium and plastic limit analyses are developed on the basis of two proposed failure mechanisms in association with an optimization algorithm. The limit analysis is conducted by using the kinematic element method (KEM), and finite-difference package is used for numerical simulations. The efficiency factors of bearing capacity are calculated at various spacings between two neighboring footings for practical range of friction angles (25°≤ϕ≤40° ) in accordance with different solutions. Thereafter, the results obtained from the proposed solutions are compared with those reported from existing experimental, theoretical, and numerical studies. In addition, the reliability of the proposed mechanisms is justified through a series of comparisons with the failure patterns and the shear bands obtained from numerical simulations at different spacings. These comparisons indicated that despite the relative simplicity of proposed solutions, bearing capacities and failure patterns are in excellent accordance with numerical, analytical, and experimental results.


  • Numerical Study on Backfilling the Tail Void Using a Two-Component Grout

    by Ravi Shah, Arash A. Lavasan, Daniele Peila, Carmine Todaro, Andrea Luciani, Tom Schanz

    In shielded mechanized tunneling, the annular gap caused by the tunnel boring machine (TBM) driving must be backfilled instantaneously using a suitable grout. A two-component grout composed of a chemically retarded cement slurry and an accelerator is pumped into the annular gap behind the TBM shield, where it gels and attains sufficient mechanical stiffness in a very short time. This property of the grout helps restrict immediate ground movements adjacent to the TBM tail shield and reduce volume loss. In this study, the hardened two-component mix is tested using a confined oedometric condition, and a complete time-dependent hardening stiffness evolution is developed. Moreover, the freshly prepared grout is tested in terms of its performance suitability (storage and transportation) and serviceability owing to permeability and dewatering. The obtained parameters from the oedometer tests are incorporated into a numerical simulation of an earth pressure balance (EPB) excavation focusing on modeling of the backfilling procedure using finite-difference method (FDM) software. The study also focuses on distinguishing between two commonly used backfilling techniques implemented in numerical analyses. The numerical model consists of testing a regular tunnel section using a newly introduced hardening soil (HS) constitutive model with the soil parameters obtained from the Torino, Italy, metro case. Another set of synthetic softer soil parameters are chosen to highlight the soil properties in the model response. The two-component grout satisfies all the prerequisites for a good backfilling material in its fresh and hardened state. The grout attains sufficient mechanical strength in a very short time, remains impermeable, and achieves a stiffness of 43 MPa in 28 days. The results obtained from the oedometer tests enable development of a complete time-dependent stiffness evolution of the grout. The implementation of hardening behavior of the two-component grout is evident in terms of ground settlements when compared with the conventional backfilling simulation technique.


  • Analysis of Interfering Circular Footings on Reinforced Soil by Physical and Numerical Approaches Considering Strain-Dependent Stiffness

    by Arash Alimardani Lavasan, Mahmoud Ghazavi, Tom Schanz

    This paper numerically examines the bearing capacity, settlement, and failure kinematics of two closely spaced circular footings on reinforced soil. A number of large-scale tests are performed to identify the influence of the tilt of interfering footings on their ultimate bearing capacity and settlement, and these experimental results are used to verify the numerical model. Because the mobilization of shear strength in soil and tensile resistance in the geogrid depend to a large extent on the strain level (especially in small strains), a nonlinear elastic-plastic constitutive model in conjunction with a nonassociated flow rule is proposed. In addition, the model accounts for the dependency of the friction and dilation angles on the strain level in the plastic domain. The constitutive parameters are calibrated for the triaxial loading test, whereas the numerical model for the closely spaced footings is verified with reference to the large-scale test results. Thereafter, the ultimate bearing capacity and settlement of interfering circular footings on reinforced soil are studied for different configurations, and the critical size and position of reinforcements that maximize the bearing capacity are characterized. Results show that the ultimate bearing capacity increases up to a maximum of 40 and 90% by the use of one and two layers of geogrid, respectively. Beyond the bearing capacity, the settlement of adjacent circular footings increases up to 45% (compared with a single footing with the same safety factor). Finally, the influence of reinforcing soil on failure kinematics and soil deformation pattern is investigated.


  • Predicting the Maximum Shear Modulus of Sands Containing Nonplastic Fines

    by Meisam Goudarzy, Negar Rahemi, Mizanur Rahman, Tom Schanz

    There are some attempts to evaluate Hardin’s equation for transition soils, i.e., sand mixed with a systematic increase of fines (particle size≤0.075  mm ) content, fc . The most common finding is that maxmium shear modulus, Gmax , decreases with increasing fc , and there are attempts to capture the effect of fc on Gmax by considering Gmax of clean sand as a reference. These are done by (1) developing empirical relations of A , n , c , or d with fc ; (2) using equivalent granular void ratio, e* , instead of void ratio, e in Hardin’s equation; and (3) using a critical state (CS) approach. This paper presents 288 resonant column Gmax data for clean Hostun sand and Hostun sand mixed with 5, 10, 20, and 30% nonplastic quartz powder. It is found that when e in a pre-established Hardin equation for clean Hostun sand is replaced by e* , Hardin’s equation can predict Gmax for Hostun sand with fc with good accuracy. Only soil grading properties, e.g., D10 and d50 , are required as inputs to convert e to e* . This is a significant advantage over a recently proposed CS approach which requires critical state lines (CSLs) data for each fc .


  • Swelling Behavior of Bentonite-Based Backfilling Materials in Nuclear Waste Repository Conditions

    by Yasir Al-Badran, Wiebke Baille, Snehasis Tripathy, Tom Schanz

    During the postconstruction phase, the stress equilibrium conditions within the proposed underground nuclear waste repositories may alter because of various factors, such as far-field mining activity, fluctuation of the groundwater table, and seepage erosion. A reduction in the transmitted stress from the host rock may destabilize the isochoric condition, leading to swelling displacement of backfilling and buffer materials. In the current study, the swelling behavior of bentonite-based backfilling materials was studied. Laboratory tests were carried out on compacted bentonite (dry density=1.26  Mg/m3 ) and bentonite-sand (70% bentonite, 30% sand, dry density=1.50  Mg/m3 ) specimens in a strain-controlled oedometer. First, compacted specimens were hydrated with distilled water under constant volume condition. Next, predetermined displacements were introduced in a step-wise manner that caused expansion of the specimens. The swelling pressures of the specimens were measured under a constant-volume condition at each induced strain. The test results showed that induced strains caused a decrease in the swelling pressures of the saturated backfilling materials. A decrease in the swelling pressure for a maximum induced strain of approximately 1.6% was found to be approximately 19% for the bentonite specimen and approximately 30% for the bentonite-sand specimen. It was shown how the swelling index of backfilling materials can be used to assess the recoverable swelling pressure following any induced strain.