Boguslaw Pisarek
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Boguslaw Pisarek has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Cezary Rapiejko
Department of Materials Engineering and Production Systems, Lodz University of Technology, 90-924 Lodz, Poland
11 shared publications - Tadeusz Pacyniak
Department of Materials Engineering and Production Systems, Lodz University of Technology, 90-924 Lodz, Poland
11 shared publications - Tomasz Szymczak
Department of Materials Engineering and Production Systems, Lodz University of Technology, 90-924 Lodz, Poland
5 shared publications - Bartłomiej Januszewicz
Institute of Material Science and Engineering, Faculty of Mechanical Engineering, Lodz University of Technology, 90-924 Lodz, Poland
3 shared publications - Grzegorz Gumienny
Department of Materials Engineering and Production Systems, Lodz University of Technology, 90-924 Lodz, Poland
3 shared publications - Pawel Just
Department of Materials Engineering and Production Systems, Lodz University of Technology, 90-924 Lodz, Poland
3 shared publications
Latest Publications
- 30 December 2025
- Published by Polish Academy of Sciences Chancellery in Archives of Foundry Engineering
- p. 175-189
Manufacture of Casts Using Replicast CS Technology from Patterns Produced on Injection Molding
The paper discusses issues in the field of casting using the Replicast CS technology and explores the possibilities of applying patterns made on injection moulders with gas injection moulding technology. The scope of the study included designing a Celtic stone pattern and selecting suitable gating system elements based on the analysis of simulation results obtained with MAGMASOFT® v.5.3 software. Determining the dimensions of individual elements, as well as positioning the patterns relative to the pouring gate, was empirical. Changes were made to ensure the production of casts free from defects. Verification focused on parameters such as: solidification temperature, porosity, and metal flow in the mould. After conducting a simulation in MAGMASOFT® v5.3 and achieving satisfactory results, patterns were produced on an injection moulding process, pattern systems were prepared, and ceramic moulds were made. The moulds were then fired, and simultaneously, the patterns were removed from the mould cavities, which were subsequently filled with aluminum alloy AlSi11. An analysis of the quality of the prepared moulds and test casts was also performed.
- 30 December 2025
- Published by Polish Academy of Sciences Chancellery in Archives of Foundry Engineering
- p. 175-189
Manufacture of Casts Using Replicast CS Technology from Patterns Produced on Injection Molding
The paper discusses issues in the field of casting using the Replicast CS technology and explores the possibilities of applying patterns made on injection moulders with gas injection moulding technology. The scope of the study included designing a Celtic stone pattern and selecting suitable gating system elements based on the analysis of simulation results obtained with MAGMASOFT® v.5.3 software. Determining the dimensions of individual elements, as well as positioning the patterns relative to the pouring gate, was empirical. Changes were made to ensure the production of casts free from defects. Verification focused on parameters such as: solidification temperature, porosity, and metal flow in the mould. After conducting a simulation in MAGMASOFT® v5.3 and achieving satisfactory results, patterns were produced on an injection moulding process, pattern systems were prepared, and ceramic moulds were made. The moulds were then fired, and simultaneously, the patterns were removed from the mould cavities, which were subsequently filled with aluminum alloy AlSi11. An analysis of the quality of the prepared moulds and test casts was also performed.
- 30 December 2025
- Published by Polish Academy of Sciences Chancellery in Archives of Foundry Engineering
- p. 124-132
The Effect of Changes in Degassing Parameters on Gasification and Crystallization of EN AC-46000 Alloy
The paper presents research on the influence of degassing process parameters on the crystallization and gasification of EN AC-46000 alloy (designation according to chemical composition – AlSi9Cu3(Fe)). After melting, the alloy was degassed using Ecosal Al113.S solid refiner and by blowing with an inert gas: nitrogen or argon. Various solid degasser contents and various nitrogen and argon blowing times were used. Thermal and derivative analysis (TDA) were used to study the crystallization process of Al-Si alloy. The density index as well as hydrogen content in the liquid alloy were determined. Using Alu Speed Tester, it was demonstrated that the lowest density index and hydrogen content were obtained in the alloy degassed with the use of Ecosal at a concentration of 1% and then blown with argon for 15 minutes. It has been shown that increasing the efficiency of the degassing process results in prolonging the crystallization time of the tested alloy, and in particular, the crystallization time of αAl + β(Si) binary eutectic. The justification given was the probable removal of small solid particles from the liquid metal, which could form the basis for heterogeneous nucleation of the Al-Si alloy component phases during degassing.
- 30 December 2025
- Published by Polish Academy of Sciences Chancellery in Archives of Foundry Engineering
- p. 124-132
The Effect of Changes in Degassing Parameters on Gasification and Crystallization of EN AC-46000 Alloy
The paper presents research on the influence of degassing process parameters on the crystallization and gasification of EN AC-46000 alloy (designation according to chemical composition – AlSi9Cu3(Fe)). After melting, the alloy was degassed using Ecosal Al113.S solid refiner and by blowing with an inert gas: nitrogen or argon. Various solid degasser contents and various nitrogen and argon blowing times were used. Thermal and derivative analysis (TDA) were used to study the crystallization process of Al-Si alloy. The density index as well as hydrogen content in the liquid alloy were determined. Using Alu Speed Tester, it was demonstrated that the lowest density index and hydrogen content were obtained in the alloy degassed with the use of Ecosal at a concentration of 1% and then blown with argon for 15 minutes. It has been shown that increasing the efficiency of the degassing process results in prolonging the crystallization time of the tested alloy, and in particular, the crystallization time of αAl + β(Si) binary eutectic. The justification given was the probable removal of small solid particles from the liquid metal, which could form the basis for heterogeneous nucleation of the Al-Si alloy component phases during degassing.
- 17 March 2025
- Published by Polish Academy of Sciences Chancellery in Archives of Foundry Engineering
Analysis of the Applicability of Heat Treatment of EN AC-46000 Alloy Castings Made with Vacuum-Assisted HPDC Technology
The aim of the study was optimization of the technological parameters of the thermal treatment of EN AC-46000 alloy products made in the vacuum aided HPDC technology in the function of simultaneous maximization of the alloy’s mechanical properties with no deformation of the cast’s surface. The produced casts were subjected to thermal treatment T6 according to the elaborated experiment plan. The samples were examined in respect of selected mechanical properties as well as the presence of deformation on the castings surfaces. Also performed was an analysis of the castings microstructure as well as optimization of the technological parameters of the supersaturation and ageing process by means of statistical methods, i.e. the Box-Wilson optimization method (Stage I) and stepwise multiple regression in the Statgraphics software (Stage II). Also, a simulation was carried out, predicting the mechanical properties for the specific supersaturation and ageing parameters, from which optimized values of the setpoints of both processes were obtained. The study presents the results of validation tests of pressure casts subjected to thermal treatment performed according to the previously determined optimal parameters of supersaturation and ageing. These results confirmed the effectiveness of the conducted precipitation hardening treatment.
- 17 March 2025
- Published by Polish Academy of Sciences Chancellery in Archives of Foundry Engineering
Analysis of the Applicability of Heat Treatment of EN AC-46000 Alloy Castings Made with Vacuum-Assisted HPDC Technology
The aim of the study was optimization of the technological parameters of the thermal treatment of EN AC-46000 alloy products made in the vacuum aided HPDC technology in the function of simultaneous maximization of the alloy’s mechanical properties with no deformation of the cast’s surface. The produced casts were subjected to thermal treatment T6 according to the elaborated experiment plan. The samples were examined in respect of selected mechanical properties as well as the presence of deformation on the castings surfaces. Also performed was an analysis of the castings microstructure as well as optimization of the technological parameters of the supersaturation and ageing process by means of statistical methods, i.e. the Box-Wilson optimization method (Stage I) and stepwise multiple regression in the Statgraphics software (Stage II). Also, a simulation was carried out, predicting the mechanical properties for the specific supersaturation and ageing parameters, from which optimized values of the setpoints of both processes were obtained. The study presents the results of validation tests of pressure casts subjected to thermal treatment performed according to the previously determined optimal parameters of supersaturation and ageing. These results confirmed the effectiveness of the conducted precipitation hardening treatment.
- Open Access
The Effect of Sr, Ti, and B on the Crystallization Process and Mechanical Properties of the AlSi9Cu3(Fe) Alloy
This article presents studies on the effect of Sr and TiB on the crystallization process, mechanical properties, hardness, and density index of the Al-Si alloy from the EN AC-46000 group, with a narrowed chemical composition, produced by die-casting and HPDC (high-pressure die casting) technology. The research used the Box–Wilson method to design the experiment and stepwise multiple regression. To identify the optimal amount of Sr and Ti in the analyzed alloy that would simultaneously guarantee the maximization of UTS, YS, Agt, and HBW and the minimization of the DI (density index), multi-criteria optimization was performed. The modifiers were added to the liquid alloy as AlSr10 and AlTi5B1 master alloys. It was found that for 0.02–0.04 wt.% Sr and 0.05–0.08 wt.% Ti in the die castings, the highest mechanical properties, such as UTS, YS, Agt, and HBW (treated as stimulants in the experiment), can be obtained simultaneously with the lowest alloy gasification identified by DI (treated as a destimulant in the experiment). It was also confirmed that the same amount of the above-mentioned elements in HPDC castings caused an increase in UTS by approx. 14%, YS by approx. 6%, A by approx. 47%, and HBW by approx. 13%, with a relatively small increase in DI by approx. 5% compared to the unmodified alloy.
Open AccessThe Effect of Sr, Ti, and B on the Crystallization Process and Mechanical Properties of the AlSi9Cu3(Fe) Alloy
This article presents studies on the effect of Sr and TiB on the crystallization process, mechanical properties, hardness, and density index of the Al-Si alloy from the EN AC-46000 group, with a narrowed chemical composition, produced by die-casting and HPDC (high-pressure die casting) technology. The research used the Box–Wilson method to design the experiment and stepwise multiple regression. To identify the optimal amount of Sr and Ti in the analyzed alloy that would simultaneously guarantee the maximization of UTS, YS, Agt, and HBW and the minimization of the DI (density index), multi-criteria optimization was performed. The modifiers were added to the liquid alloy as AlSr10 and AlTi5B1 master alloys. It was found that for 0.02–0.04 wt.% Sr and 0.05–0.08 wt.% Ti in the die castings, the highest mechanical properties, such as UTS, YS, Agt, and HBW (treated as stimulants in the experiment), can be obtained simultaneously with the lowest alloy gasification identified by DI (treated as a destimulant in the experiment). It was also confirmed that the same amount of the above-mentioned elements in HPDC castings caused an increase in UTS by approx. 14%, YS by approx. 6%, A by approx. 47%, and HBW by approx. 13%, with a relatively small increase in DI by approx. 5% compared to the unmodified alloy.
- Open Access
Effect of Degassing Parameters on Mechanical Properties of EN AC-46000 Gravity Die Castings
The article is devoted to the optimization of the degassing parameters of the AlSi9Cu3(Fe) alloy. The alloy was degassed with a solid degasser (Ecosal) and nitrogen or argon. The variable parameters were time and type of degasser. The test castings were made in permanent molds with an internal diameter of 25 mm and a length of 150 mm. The effect of the degassing time and the amount of degasser on the mechanical properties, as well as the hydrogen content and density index were investigated. The ALU SPEED TESTER developed by FMA was used to test the hydrogen content and the density index. Magmasoft software was used to design the geometry of the test castings. A significant effect of the solid degasser and degassing time on both the density index and the hydrogen content was demonstrated. Replacing nitrogen with argon did not bring any significant improvement in the above-mentioned parameters. The effect of degassing parameters on the mechanical properties of the EN AC-46000 alloy was much less significant, but was still visible. The optimal degassing parameters needed to obtain the highest strength parameters of the EN AC-46000 gravity die castings were determined.
Open AccessEffect of Degassing Parameters on Mechanical Properties of EN AC-46000 Gravity Die Castings
The article is devoted to the optimization of the degassing parameters of the AlSi9Cu3(Fe) alloy. The alloy was degassed with a solid degasser (Ecosal) and nitrogen or argon. The variable parameters were time and type of degasser. The test castings were made in permanent molds with an internal diameter of 25 mm and a length of 150 mm. The effect of the degassing time and the amount of degasser on the mechanical properties, as well as the hydrogen content and density index were investigated. The ALU SPEED TESTER developed by FMA was used to test the hydrogen content and the density index. Magmasoft software was used to design the geometry of the test castings. A significant effect of the solid degasser and degassing time on both the density index and the hydrogen content was demonstrated. Replacing nitrogen with argon did not bring any significant improvement in the above-mentioned parameters. The effect of degassing parameters on the mechanical properties of the EN AC-46000 alloy was much less significant, but was still visible. The optimal degassing parameters needed to obtain the highest strength parameters of the EN AC-46000 gravity die castings were determined.
- Open Access
- 1 December 2020
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 14 (4) , 11-20
Selection of the Technological Ceramic Layer Thickness in an HPDC Machine Plunger in the Aspect of its Strength
A way how to select the ceramic coating thickness with respect to axially symmetrical thermal stresses in a casting machine piston with a horizontal shot sleeve has been discussed. An application of a technological ceramic outer layer in the piston enhances its tribological properties. The...
- 1 December 2020
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 14 (4) , 11-20
Open AccessSelection of the Technological Ceramic Layer Thickness in an HPDC Machine Plunger in the Aspect of its Strength
A way how to select the ceramic coating thickness with respect to axially symmetrical thermal stresses in a casting machine piston with a horizontal shot sleeve has been discussed. An application of a technological ceramic outer layer in the piston enhances its tribological properties. The...
- Open Access
- 1 June 2020
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 14 (2) , 1-12
Mechanical and Thermal Stresses in an HPDC Machine Plunger During the Dosing and Filling Process
Distributions of mechanical and thermal stresses in a plunger of the high pressure die casting machine with a horizontal shot sleeve have been considered for a flat thermal stationary problem. An axial pressure of the plunger pressing in the technological process has been accounted for as well. Principal and equivalent stresses have been determined within two different hypotheses on the strength of materials, including one theory covering various allowable stresses in tension and compression. Four plunger material variants have been analysed.
- 1 June 2020
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 14 (2) , 1-12
Open AccessMechanical and Thermal Stresses in an HPDC Machine Plunger During the Dosing and Filling Process
Distributions of mechanical and thermal stresses in a plunger of the high pressure die casting machine with a horizontal shot sleeve have been considered for a flat thermal stationary problem. An axial pressure of the plunger pressing in the technological process has been accounted for as well. Principal and equivalent stresses have been determined within two different hypotheses on the strength of materials, including one theory covering various allowable stresses in tension and compression. Four plunger material variants have been analysed.
- Open Access
- 17 April 2020
- Published by Institute of Archaeology and Ethnology, Polish Academy of Sciences in Sprawozdania Archeologiczne
- Vol. 73 (2)
Bronze bracelets deposit from Niewierszyn by the Pilica River
In the autumn of 2017 in Niewierszyn in the Aleksandrów commune, a deposit of two bronze bracelets was discovered. The discovery site was on the edge of the Pilica floodplain terrace.The bracelets were almost identical in size and ornamentation. Also, the chemical composition of the bronze from which they were made was very similar. It may be hypothesised that the ornaments were made by the same manufacturer, probably at a similar time. Based on the analysis of the form and ornamentation, the bracelets in question can be dated to HA1. This dating corresponds to the settling of the areas in the Pilica river basin by communities associated with the Konstantynów Łódzki group, characterized by features of the early Urnfield culture. Virtual modelling of casting and an experimental cast were used to elucidate the manufacturing technique. Apart from a chronological and cultural analysis, the text attempts to show the hoard against a wider (micro-regional) settlement background, including through potential visibility analysis.
- 17 April 2020
- Published by Institute of Archaeology and Ethnology, Polish Academy of Sciences in Sprawozdania Archeologiczne
- Vol. 73 (2)
Open AccessBronze bracelets deposit from Niewierszyn by the Pilica River
In the autumn of 2017 in Niewierszyn in the Aleksandrów commune, a deposit of two bronze bracelets was discovered. The discovery site was on the edge of the Pilica floodplain terrace.The bracelets were almost identical in size and ornamentation. Also, the chemical composition of the bronze from which they were made was very similar. It may be hypothesised that the ornaments were made by the same manufacturer, probably at a similar time. Based on the analysis of the form and ornamentation, the bracelets in question can be dated to HA1. This dating corresponds to the settling of the areas in the Pilica river basin by communities associated with the Konstantynów Łódzki group, characterized by features of the early Urnfield culture. Virtual modelling of casting and an experimental cast were used to elucidate the manufacturing technique. Apart from a chronological and cultural analysis, the text attempts to show the hoard against a wider (micro-regional) settlement background, including through potential visibility analysis.
- Open Access
- 20 December 2017
- Published by Walter de Gruyter GmbH in Archives of Foundry Engineering
- Vol. 17 (4) , 7-12
Tribological Characterization of Al-bronzes Used as Mold Materials
Among the copper based alloys, Cu-Al-X bronzes are commonly used as mold materials due to their superior physical and chemical properties. Mold materials suffer from both wear and corrosion, thus, it is necessary to know which one of the competitive phenomenon is dominant during the service conditions. In this study, tribo-corrosion behavior of CuAl10Ni5Fe4 and CuAl14Fe4Mn2Co alloys were studied and electrochemical measurements were carried out using three electrode system in 3.5 % NaCl solution in order to evaluate their corrosion resistance. In tribo-corrosion tests, alloys were tested against zirconia ball in 3.5 % NaCl solution, under 10N load with 0.04 m/s sliding speed during 300 and 600 m. The results indicate that (i) CuAl10Ni5Fe4 alloy is more resistant to NaCl solution compared to CuAl14Fe4Mn2Co alloy that has major galvanic cells within its matrix, (ii) although CuAl10Ni5Fe4 alloy has lower coefficient of friction value, it suffers from wear under dry sliding conditions, (iii) as the sliding distance increases, corrosion products on CuAl14Fe4Mn2Co surface increase at a higher rate compared to CuAl10Ni5Fe4 leading to a decrease in volume loss due to the lubricant effect of copper oxides.
- 20 December 2017
- Published by Walter de Gruyter GmbH in Archives of Foundry Engineering
- Vol. 17 (4) , 7-12
Open AccessTribological Characterization of Al-bronzes Used as Mold Materials
Among the copper based alloys, Cu-Al-X bronzes are commonly used as mold materials due to their superior physical and chemical properties. Mold materials suffer from both wear and corrosion, thus, it is necessary to know which one of the competitive phenomenon is dominant during the service conditions. In this study, tribo-corrosion behavior of CuAl10Ni5Fe4 and CuAl14Fe4Mn2Co alloys were studied and electrochemical measurements were carried out using three electrode system in 3.5 % NaCl solution in order to evaluate their corrosion resistance. In tribo-corrosion tests, alloys were tested against zirconia ball in 3.5 % NaCl solution, under 10N load with 0.04 m/s sliding speed during 300 and 600 m. The results indicate that (i) CuAl10Ni5Fe4 alloy is more resistant to NaCl solution compared to CuAl14Fe4Mn2Co alloy that has major galvanic cells within its matrix, (ii) although CuAl10Ni5Fe4 alloy has lower coefficient of friction value, it suffers from wear under dry sliding conditions, (iii) as the sliding distance increases, corrosion products on CuAl14Fe4Mn2Co surface increase at a higher rate compared to CuAl10Ni5Fe4 leading to a decrease in volume loss due to the lubricant effect of copper oxides.
- Open Access
- 20 December 2017
- Published by Walter de Gruyter GmbH in Archives of Foundry Engineering
- Vol. 17 (4) , 127-132
Simulation of Stress Distribution in a Thick- Walled Bushing Produced by Die-Casting
Metallographic investigations and a computer simulation of stresses in a gravity die-casting bushing were performed. Simulation of the casting process, solidification of the thick-walled bushing and calculations of the stress was performed using MAGMA5.3 software. The size variability of phases κII affecting the formation of phase stresses σf, depending on the location of the metallographic test area, was identified. The distribution of thermal σt and shrinkage stresses σs, depending on the location of the control point SC in the bushing's volume, was estimated. Probably the nature of these stresses will change slightly even after machining. This can cause variations in operating characteristics (friction coefficient, wear). Due to the strong inhomogeneity of the stress distribution in the bushing's casting, it is necessary to perform further tests of the possibility to conduct thermal treatment guaranteeing homogenization of the internal stresses in the casting, as well as to introduce changes in the bushing' s construction and the casting technology. The paper presents the continuation of the results of research aimed at identifying the causes of defects in the thick-walled bushing, die-casting made of CuAl10Fe5Ni5Cr aluminium bronze.
- 20 December 2017
- Published by Walter de Gruyter GmbH in Archives of Foundry Engineering
- Vol. 17 (4) , 127-132
Open AccessSimulation of Stress Distribution in a Thick- Walled Bushing Produced by Die-Casting
Metallographic investigations and a computer simulation of stresses in a gravity die-casting bushing were performed. Simulation of the casting process, solidification of the thick-walled bushing and calculations of the stress was performed using MAGMA5.3 software. The size variability of phases κII affecting the formation of phase stresses σf, depending on the location of the metallographic test area, was identified. The distribution of thermal σt and shrinkage stresses σs, depending on the location of the control point SC in the bushing's volume, was estimated. Probably the nature of these stresses will change slightly even after machining. This can cause variations in operating characteristics (friction coefficient, wear). Due to the strong inhomogeneity of the stress distribution in the bushing's casting, it is necessary to perform further tests of the possibility to conduct thermal treatment guaranteeing homogenization of the internal stresses in the casting, as well as to introduce changes in the bushing' s construction and the casting technology. The paper presents the continuation of the results of research aimed at identifying the causes of defects in the thick-walled bushing, die-casting made of CuAl10Fe5Ni5Cr aluminium bronze.