Henry A. Sodano
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Henry A. Sodano has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
Haixiong Tang
Department of Materials Science and Engineering University of Florida Gainesville FL 32611 USA
5 shared publicationsYirong Lin
Department of Mechanical Engineering, University of Texas at El Paso, El Paso, TX 79968, USA
5 shared publicationsZhi Zhou
Department of Materials Science and Engineering, University of Florida, Gainesville, FL, 32611, USA
5 shared publicationsAneesh Koka
Mechanical and Aerospace Engineering University of Florida Gainesville FL 32611 USA
2 shared publications- Christopher C. Bowland
Carbon and Composites Group Chemical Sciences Division Oak Ridge National Laboratory Oak Ridge TN 37830 USA
2 shared publications Brendan A. Patterson
Univ. of Florida (United States)
1 shared publication
Latest Publications
- 10 April 2017
- Published by SPIE-Intl Soc Optical Eng
- p. 101720L-101720L-10
Piezoelectric interfaces enabled energy harvesting and tailored damping in fiber composites
- 10 April 2017
- Published by SPIE-Intl Soc Optical Eng
- p. 101720L-101720L-10
Piezoelectric interfaces enabled energy harvesting and tailored damping in fiber composites
- 13 October 2014
- Published by Wiley in Advanced Materials
- Vol. 26 (45) , 7547-7554
Scalable Synthesis of Morphotropic Phase Boundary Lead Zirconium Titanate Nanowires for Energy Harvesting
Lead zirconium titanate (PZT) nanowires are synthesized using a scalable two-step hydrothermal reaction. The piezoelectric coupling coefficient of the PZT NWs shows the highest value for PZT nanowires in the literature (80 ± 5 pm/V). A PZT-NW-based nanocomposite is fabricated to demonstrate an energy-harvesting application with an open-circuit voltage up to 7 V and a power density up to 2.4 μW/cm3.
- 13 October 2014
- Published by Wiley in Advanced Materials
- Vol. 26 (45) , 7547-7554
Scalable Synthesis of Morphotropic Phase Boundary Lead Zirconium Titanate Nanowires for Energy Harvesting
Lead zirconium titanate (PZT) nanowires are synthesized using a scalable two-step hydrothermal reaction. The piezoelectric coupling coefficient of the PZT NWs shows the highest value for PZT nanowires in the literature (80 ± 5 pm/V). A PZT-NW-based nanocomposite is fabricated to demonstrate an energy-harvesting application with an open-circuit voltage up to 7 V and a power density up to 2.4 μW/cm3.
- 13 August 2014
- Published by Wiley in Advanced Functional Materials
- Vol. 24 (40) , 6303-6308
Multifunctional Barium Titanate Coated Carbon Fibers
Multifunctional materials have received significant research interest due to the potential for performance enhancements over traditional materials through the integration of responsive properties. Composite materials are ideally suited for use as multifunctional materials due to their use of two or more phases and the ease at which their properties can be anisotropically tailored. Here, a methodology for the integration of ferroelectricity into a fiber reinforced polymer composite is presented by synthesizing a barium titanate nanowire film on the surface of carbon fibers using a novel two‐step hydrothermal process. A refined piezoelectric force microscopy method is used to quantify the piezoelectric properties of the core–shell fiber resulting in an average d33 of 31.6 ± 14.5 pm V−1 and an average d31 of −5.4 ± 3.2 pm V−1. The multifunctionality of this piezoelectric coated fiber is demonstrated through excitation of a cantilevered fiber with a 0.5 g sinusoidal base acceleration at the fiber's fundamental resonant frequency, producing a root‐mean‐square voltage of 16.4 mV. This result demonstrates the ferroelectric properties of the multifunctional structural fiber and its application for sensing and energy harvesting.
- 13 August 2014
- Published by Wiley in Advanced Functional Materials
- Vol. 24 (40) , 6303-6308
Multifunctional Barium Titanate Coated Carbon Fibers
Multifunctional materials have received significant research interest due to the potential for performance enhancements over traditional materials through the integration of responsive properties. Composite materials are ideally suited for use as multifunctional materials due to their use of two or more phases and the ease at which their properties can be anisotropically tailored. Here, a methodology for the integration of ferroelectricity into a fiber reinforced polymer composite is presented by synthesizing a barium titanate nanowire film on the surface of carbon fibers using a novel two‐step hydrothermal process. A refined piezoelectric force microscopy method is used to quantify the piezoelectric properties of the core–shell fiber resulting in an average d33 of 31.6 ± 14.5 pm V−1 and an average d31 of −5.4 ± 3.2 pm V−1. The multifunctionality of this piezoelectric coated fiber is demonstrated through excitation of a cantilevered fiber with a 0.5 g sinusoidal base acceleration at the fiber's fundamental resonant frequency, producing a root‐mean‐square voltage of 16.4 mV. This result demonstrates the ferroelectric properties of the multifunctional structural fiber and its application for sensing and energy harvesting.
- Top Cited Papers
- 30 May 2014
- Published by Wiley in Advanced Functional Materials
- Vol. 24 (33) , 5261-5268
Self‐Healing Polyurethanes with Shape Recovery
Two new thermoresponsive self‐healing polyurethanes (1DA1T and 1.5DA1T) based on the Diels–Alder (DA) reaction between furan and maleimide moieties are developed that use the shape‐memory effect to bring crack faces into intimate contact such that healing can take place. Unlike other self‐healing polymers, these polymers do not require external forces to close cracks but rather they use the shape‐memory effect to autonomously close the crack. Both polyurethanes have a stable polymer structure and comparable mechanical properties to commercial epoxies. A differential scanning calorimeter is employed to check the glass transition temperature of the polymers as well as the DA and retro‐DA (rDA) reaction temperatures. These DA and rDA reactions are confirmed with variable‐temperature proton nuclear magnetic resonance. Healing efficiency is calculated using a measurement of the failure load from compact tension testing. The results show that the shape‐memory effect can replace external forces to close two crack surfaces and the DA reaction can be repeatedly employed to heal the cracks.
- 30 May 2014
- Published by Wiley in Advanced Functional Materials
- Vol. 24 (33) , 5261-5268
Top Cited PapersSelf‐Healing Polyurethanes with Shape Recovery
Two new thermoresponsive self‐healing polyurethanes (1DA1T and 1.5DA1T) based on the Diels–Alder (DA) reaction between furan and maleimide moieties are developed that use the shape‐memory effect to bring crack faces into intimate contact such that healing can take place. Unlike other self‐healing polymers, these polymers do not require external forces to close cracks but rather they use the shape‐memory effect to autonomously close the crack. Both polyurethanes have a stable polymer structure and comparable mechanical properties to commercial epoxies. A differential scanning calorimeter is employed to check the glass transition temperature of the polymers as well as the DA and retro‐DA (rDA) reaction temperatures. These DA and rDA reactions are confirmed with variable‐temperature proton nuclear magnetic resonance. Healing efficiency is calculated using a measurement of the failure load from compact tension testing. The results show that the shape‐memory effect can replace external forces to close two crack surfaces and the DA reaction can be repeatedly employed to heal the cracks.
- 7 April 2014
- Published by Wiley in Advanced Energy Materials
- Vol. 4 (11) , 1301660
A Low‐Frequency Energy Harvester from Ultralong, Vertically Aligned BaTiO3 Nanowire Arrays
- 7 April 2014
- Published by Wiley in Advanced Energy Materials
- Vol. 4 (11) , 1301660
A Low‐Frequency Energy Harvester from Ultralong, Vertically Aligned BaTiO3 Nanowire Arrays
- 22 October 2013
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 7 (1) , 288-296
Vertically aligned BaTiO3nanowire arrays for energy harvesting
Nano-electromechanical systems (NEMS) developed using piezoelectric nanowires (NWs) have gained immense interest in energy harvesting applications as they are able to convert several different forms of mechanical energy sources into electric power and thereby function as reliable power sources for ultra-low power wireless electronics. In this work, a piezoelectric NEMS vibrational energy harvester is fabricated through the development of a synthesis process for vertically aligned barium titanate (BaTiO3) nanowire (NW) arrays directly on a conductive substrate. These poled ferroelectric NW arrays are characterized through direct vibration excitation and demonstrated to provide efficient harvesting of mechanical vibrational energy producing an average power density of ∼6.27 μW cm−3 from 1g acceleration. In order to substantiate the superior energy harvesting performance of the newly developed BaTiO3 NW arrays, a direct comparison is made with conventional ZnO NW arrays. Here, we clearly report that the ferroelectric BaTiO3 NW NEMS energy harvester has ∼16 times greater power density than the ZnO NW NEMS energy harvester from the same acceleration input.
- 22 October 2013
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 7 (1) , 288-296
Vertically aligned BaTiO3nanowire arrays for energy harvesting
Nano-electromechanical systems (NEMS) developed using piezoelectric nanowires (NWs) have gained immense interest in energy harvesting applications as they are able to convert several different forms of mechanical energy sources into electric power and thereby function as reliable power sources for ultra-low power wireless electronics. In this work, a piezoelectric NEMS vibrational energy harvester is fabricated through the development of a synthesis process for vertically aligned barium titanate (BaTiO3) nanowire (NW) arrays directly on a conductive substrate. These poled ferroelectric NW arrays are characterized through direct vibration excitation and demonstrated to provide efficient harvesting of mechanical vibrational energy producing an average power density of ∼6.27 μW cm−3 from 1g acceleration. In order to substantiate the superior energy harvesting performance of the newly developed BaTiO3 NW arrays, a direct comparison is made with conventional ZnO NW arrays. Here, we clearly report that the ferroelectric BaTiO3 NW NEMS energy harvester has ∼16 times greater power density than the ZnO NW NEMS energy harvester from the same acceleration input.
- 11 September 2013
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 5 (22) , 10901-10907
Hydrothermal growth of textured BaxSr1−xTiO3 films composed of nanowires
A novel method for synthesis of Barium Strontium Titanate (BST) films with a high degree of texture is developed with a two-step hydrothermal reaction and without the need for costly equipment. The dielectric constant and ferroelectric properties of the film can be tuned by varying the Ba : Sr molar ratio of the materials. The maximum ambient temperature dielectric constant of these BST films can reach 811 when the Ba molar fraction (“x” in BaxSr1−xTiO3) is 0.71, which corresponds with the tetragonal to cubic phase transition of the solid solution. The ferroelectric behavior of the Ba0.91Sr0.09TiO3 film is confirmed by atomic force microscopy (AFM).
- 11 September 2013
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 5 (22) , 10901-10907
Hydrothermal growth of textured BaxSr1−xTiO3 films composed of nanowires
A novel method for synthesis of Barium Strontium Titanate (BST) films with a high degree of texture is developed with a two-step hydrothermal reaction and without the need for costly equipment. The dielectric constant and ferroelectric properties of the film can be tuned by varying the Ba : Sr molar ratio of the materials. The maximum ambient temperature dielectric constant of these BST films can reach 811 when the Ba molar fraction (“x” in BaxSr1−xTiO3) is 0.71, which corresponds with the tetragonal to cubic phase transition of the solid solution. The ferroelectric behavior of the Ba0.91Sr0.09TiO3 film is confirmed by atomic force microscopy (AFM).
- Top Cited Papers
- 13 December 2012
- Published by Wiley in Advanced Energy Materials
- Vol. 3 (4) , 451-456
Synthesis of High Aspect Ratio BaTiO3 Nanowires for High Energy Density Nanocomposite Capacitors
High energy density capacitors are critically important in advanced electronic devices and power systems since they can reduce the weight, size and cost required to meet a desired application. Nanocomposites hold strong potential for increasing the performance of high power energy sources; however, the energy density of most nanocomposites is still low compared to commercial capacitors and neat polymers. Here, we develop a new synthesis method for the growth of high aspect ratio barium titanate nanowires (BaTiO3) nanowires (NWs) with high yield. High energy density nanocomposite capacitors are fabricated using surface‐functionalized high aspect ratio BaTiO3 NWs in a poly(vinylidene fluoride‐trifluoroethylene‐chlorofluoroethylene) (P(VDF‐TrFE‐CFE)) matrix. At a 17.5% volume fraction, the nanocomposites show more than 45.3% increase in energy density above that of the pure P(VDF‐TrFE‐CFE) polymer (10.48 J/cc compared to 7.21 J/cc) at electric field 300 MV/m. This value is significant and exceeds those reported for the conventional polymer‐ceramic nanocomposites; it is also more than seven times larger than high performance commercial polypropylene capacitor (1.2 J/cc at 640 MV/m). In addition, our nanocomposite capacitor has a maximum power density as high as 1.2 MW/cc occurring only 1.52 μs after the start of discharge. The findings of this research could lead to enhanced interest in nanowires based nanocomposites due to their potential for achieving next generation energy storage devices.
- 13 December 2012
- Published by Wiley in Advanced Energy Materials
- Vol. 3 (4) , 451-456
Top Cited PapersSynthesis of High Aspect Ratio BaTiO3 Nanowires for High Energy Density Nanocomposite Capacitors
High energy density capacitors are critically important in advanced electronic devices and power systems since they can reduce the weight, size and cost required to meet a desired application. Nanocomposites hold strong potential for increasing the performance of high power energy sources; however, the energy density of most nanocomposites is still low compared to commercial capacitors and neat polymers. Here, we develop a new synthesis method for the growth of high aspect ratio barium titanate nanowires (BaTiO3) nanowires (NWs) with high yield. High energy density nanocomposite capacitors are fabricated using surface‐functionalized high aspect ratio BaTiO3 NWs in a poly(vinylidene fluoride‐trifluoroethylene‐chlorofluoroethylene) (P(VDF‐TrFE‐CFE)) matrix. At a 17.5% volume fraction, the nanocomposites show more than 45.3% increase in energy density above that of the pure P(VDF‐TrFE‐CFE) polymer (10.48 J/cc compared to 7.21 J/cc) at electric field 300 MV/m. This value is significant and exceeds those reported for the conventional polymer‐ceramic nanocomposites; it is also more than seven times larger than high performance commercial polypropylene capacitor (1.2 J/cc at 640 MV/m). In addition, our nanocomposite capacitor has a maximum power density as high as 1.2 MW/cc occurring only 1.52 μs after the start of discharge. The findings of this research could lead to enhanced interest in nanowires based nanocomposites due to their potential for achieving next generation energy storage devices.
- 28 June 2012
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 47 (12) , 1527-1533
Barium titanate and barium strontium titanate coated carbon fibers for multifunctional structural capacitors
Multifunctional materials can increase the performance of a system through the integration of multiple separate functional components into a single material system. This design approach offers widespread benefits and can be applied to a variety of applications. Here, we explore the integration of electrostatic energy storage and composite materials through the growth of a barium strontium titanate film on carbon fiber. The perovskite ceramic offers high dielectric constant and the use of Ba xSr1 − xTiO3 allows for the tuning of the dielectric, ferroelectric, and loss parameters to obtain an optimal energy storage stoichiometry. We have evaluated the dielectric and breakdown strength of the films to determine the energy storage density and demonstrate energy densities of 0.12 J/cc from a load-bearing fiber.
- 28 June 2012
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 47 (12) , 1527-1533
Barium titanate and barium strontium titanate coated carbon fibers for multifunctional structural capacitors
Multifunctional materials can increase the performance of a system through the integration of multiple separate functional components into a single material system. This design approach offers widespread benefits and can be applied to a variety of applications. Here, we explore the integration of electrostatic energy storage and composite materials through the growth of a barium strontium titanate film on carbon fiber. The perovskite ceramic offers high dielectric constant and the use of Ba xSr1 − xTiO3 allows for the tuning of the dielectric, ferroelectric, and loss parameters to obtain an optimal energy storage stoichiometry. We have evaluated the dielectric and breakdown strength of the films to determine the energy storage density and demonstrate energy densities of 0.12 J/cc from a load-bearing fiber.
- Open Access
- 4 April 2012
- Published by Wiley in Advanced Energy Materials
- Vol. 2 (4) , 393
Nanocomposite Capacitors: Enhanced Energy Storage in Nanocomposite Capacitors through Aligned PZT Nanowires by Uniaxial Strain Assembly (Adv. Energy Mater. 4/2012)
- 4 April 2012
- Published by Wiley in Advanced Energy Materials
- Vol. 2 (4) , 393
Open AccessNanocomposite Capacitors: Enhanced Energy Storage in Nanocomposite Capacitors through Aligned PZT Nanowires by Uniaxial Strain Assembly (Adv. Energy Mater. 4/2012)