EMEckhard Müller

Eckhard Müller

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Eckhard Müller has a total of 69 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Analyzing the Performance of Thermoelectric Generators with Inhomogeneous Legs: Coupled Material–Device Modelling for Mg2X-Based TEG Prototypes

    by Julia Camut, Eckhard Müller, Johannes de Boor

    Thermoelectric generators (TEGs) possess the ability to generate electrical power from heat. As TEGs are operated under a thermal gradient, inhomogeneous material properties—either by design or due to inhomogeneous material degradation under thermal load—are commonly found. However, this cannot be addressed using standard approaches for performance analysis of TEGs in which spatially homogeneous materials are assumed. Therefore, an innovative method of analysis, which can incorporate inhomogeneous material properties, is presented in this study. This is crucial to understand the measured performance parameters of TEGs and, from this, develop means to improve their longevity. The analysis combines experimental profiling of inhomogeneous material properties, modelling of the material properties using a single parabolic band model, and calculation of device properties using the established Constant Property Model. We compare modeling results assuming homogeneous and inhomogeneous properties to the measurement results of an Mg2(Si,Sn)-based TEG prototype. We find that relevant discrepancies lie in the effective temperature difference across the TE leg, which decreases by ~10%, and in the difference between measured and calculated heat flow, which increases from 2–15% to 9–16% when considering the inhomogeneous material. The approach confirms additional resistances in the TEG as the main performance loss mechanism and allows the accurate calculation of the impact of different improvements on the TEG’s performance.


  • Open Access

    International Round Robin Test of Thermoelectric Generator Modules

    by Pawel Ziolkowski, Przemyslaw Blaschkewitz, Byungki Ryu, SuDong Park, Eckhard Müller

    The status of metrology for the characterization of thermoelectric generator modules (TEM) is investigated in this work by an international round robin (RR) test including twelve laboratories from nine countries on three continents. Measurements have been performed with three samples of a Bi2Te3-based commercial TEM type, which has prevailed over three competing types during previous tests on the short- and long-term stability. A comparison of temperature-dependent results is provided up to 200 °C hot side temperature for the maximum power output Pmax, the incident heat flow Q˙In (at maximum efficiency conditions), and the maximum efficiency ηmax. Data evaluation from all RR participants reveals maximum standard deviations for these measurands of 27.2% (Pmax), 59.2% (Q˙In), and 25.9% (ηmax). A comparison between RR data sets and reference data from manufacturer specifications shows high deviations of up to 46%, too. These deviations reflect the absence of measurement guidelines and reference samples and confirm the need for improvements in the standardization of TEM metrology. Accordingly, the results of the RR are presented against the background of our own investigations on the uncertainty budgets for the determination of the abovementioned TEM properties using inhouse-developed characterization facilities, which comprise reference and absolute measurement techniques for the determination of heat flow.


  • Open Access

    Impact of the Dopant Species on the Thermomechanical Material Properties of Thermoelectric Mg2Si0.3Sn0.7

    by Gustavo Castillo-Hernández, Eckhard Müller, Johannes de Boor

    Thermoelectric generators are an excellent option for waste heat reuse. Materials for such devices have seen their thermoelectric properties improving constantly. The functioning of a generator, however, does not only depend on thermoelectric properties. Thermal and mechanical properties play a decisive role in the feasibility of any thermoelectric generator. To shed light on the properties exhibited by thermoelectric materials, we present the temperature dependent characterization of Young’s modulus and coefficient of thermal expansion for Mg2Si0.3Sn0.7. Comparing undoped to Bi-doped n-type and Li-doped p-type material, we investigated the influence of doping in the relevant temperature regime and found the influences to be minor, proving similar properties for n- and p-type. We found a Young’s modulus of 84 GPa for the p-type and 83 GPa for the n-type, similar to that of the undoped compound with 85 GPa. The thermal expansion coefficients of undoped, as well as n- and p-type were equally similar with values ranging from 16.5 to 17.5 × 10−6 1/K. A phase analysis was performed to further compare the two materials, finding a similar phase distribution and microstructure. Finally, using the gathered data, estimations on the possible thermally induced stresses under a temperature difference are provided to evaluate the relevance of knowing temperature dependent thermal and mechanical properties.


  • Open Access

    Overcoming Asymmetric Contact Resistances in Al-Contacted Mg2(Si,Sn) Thermoelectric Legs

    by Julia Camut, Sahar Ayachi, Gustavo Castillo-Hernández, Sungjin Park, Byungki Ryu, Sudong Park, Adina Frank, Christian Stiewe, Eckhard Müller, Johannes de Boor

    Thermoelectric generators are a reliable and environmentally friendly source of electrical energy. A crucial step for their development is the maximization of their efficiency. The efficiency of a TEG is inversely related to its electrical contact resistance, which it is therefore essential to minimize. In this paper, we investigate the contacting of an Al electrode on Mg2(Si,Sn) thermoelectric material and find that samples can show highly asymmetric electrical contact resistivities on both sides of a leg (e.g., 10 µΩ·cm2 and 200 µΩ·cm2). Differential contacting experiments allow one to identify the oxide layer on the Al foil as well as the dicing of the pellets into legs are identified as the main origins of this behavior. In order to avoid any oxidation of the foil, a thin layer of Zn is sputtered after etching the Al surface; this method proves itself effective in keeping the contact resistivities of both interfaces equally low (2) after dicing. A slight gradient is observed in the n-type leg’s Seebeck coefficient after the contacting with the Zn-coated electrode and the role of Zn in this change is confirmed by comparing the experimental results to hybrid-density functional calculations of Zn point defects.


  • Open Access

    Discrepancy between Constant Properties Model and Temperature-Dependent Material Properties for Performance Estimation of Thermoelectric Generators

    by Prasanna Ponnusamy, Johannes de Boor, Eckhard Müller

    The efficiency of a thermoelectric (TE) generator for the conversion of thermal energy into electrical energy can be easily but roughly estimated using a constant properties model (CPM) developed by Ioffe. However, material properties are, in general, temperature (T)-dependent and the CPM yields meaningful estimates only if physically appropriate averages, i.e., spatial averages for thermal and electrical resistivities and the temperature average (TAv) for the Seebeck coefficient (α), are used. Even though the use of αTAv compensates for the absence of Thomson heat in the CPM in the overall heat balance, we find that the CPM still overestimates performance (e.g., by up to 6% for PbTe) for many materials. The deviation originates from an asymmetric distribution of internally released Joule heat to either side of the TE leg and the distribution of internally released Thomson heat between the hot and cold side. The Thomson heat distribution differs from a complete compensation of the corresponding Peltier heat balance in the CPM. Both effects are estimated quantitatively here, showing that both may reach the same order of magnitude, but which one dominates varies from case to case, depending on the specific temperature characteristics of the thermoelectric properties. The role of the Thomson heat distribution is illustrated by a discussion of the transport entropy flow based on the α(T) plot. The changes in the lateral distribution of the internal heat lead to a difference in the heat input, the optimum current and thus of the efficiency of the CPM compared to the real case, while the estimate of generated power at maximum efficiency remains less affected as it is bound to the deviation of the optimum current, which is mostly <1%. This deviation can be corrected to a large extent by estimating the lateral Thomson heat distribution and the asymmetry of the Joule heat distribution. A simple guiding rule for the former is found.


  • Open Access

    Insight on the Interplay between Synthesis Conditions and Thermoelectric Properties of α-MgAgSb

    by Julia Camut, Ignacio Barber Rodriguez, Hasbuna Kamila, Aidan Cowley, Reinhard Sottong, Eckhard Mueller, Johannes de Boor

    α-MgAgSb is a very promising thermoelectric material with excellent thermoelectric properties between room temperature and 300 °C, a range where few other thermoelectric materials show good performance. Previous reports rely on a two-step ball-milling process and/or time-consuming annealing. Aiming for a faster and scalable fabrication route, herein, we investigated other potential synthesis routes and their impact on the thermoelectric properties of α-MgAgSb. We started from a gas-atomized MgAg precursor and employed ball-milling only in the final mixing step. Direct comparison of high energy ball-milling and planetary ball-milling revealed that high energy ball milling already induced formation of MgAgSb, while planetary ball milling did not. This had a strong impact on the microstructure and secondary phase fraction, resulting in superior performance of the high energy ball milling route with an attractive average thermoelectric figure of merit of z T avg = 0.9. We also show that the formation of undesired secondary phases cannot be avoided by a modification of the sintering temperature after planetary ball milling, and discuss the influence of commonly observed secondary phases on the carrier mobility and on the thermoelectric properties of α-MgAgSb.


  • Open Access

    TEG Design for Waste Heat Recovery at an Aviation Jet Engine Nozzle

    by Pawel Ziolkowski, Knud Zabrocki, Eckhard Müller

    Finite element model (FEM)-based simulations are conducted for the application of a thermoelectric generator (TEG) between the hot core stream and the cool bypass flow at the nozzle of an aviation turbofan engine. This work reports the resulting requirements on the TEG design with respect to applied thermoelectric (TE) element lengths and filling factors (F) of the TE modules in order to achieve a positive effect on the specific fuel consumption. Assuming a virtual optimized TE material and varying the convective heat transfer coefficients (HTC) between the nozzle surfaces and the gas flows, this work reports the achievable power output. System-level requirement on the gravimetric power density (>100 Wkg−1) can only be met for F ≤ 21%. When extrapolating TEG coverage to the full nozzle surface, the power output reaches 1.65 kW per engine. The assessment of further potential for power generation is demonstrated by a parametric study on F, convective HTC, and materials performance. This study confirms a feasible design range for TEG installation on the aircraft nozzle with a positive impact on the fuel consumption. This application translates into a reduction of operational costs, allowing for an economically efficient TEG-installation with respect to the cost-specific power output of modern thermoelectric materials.


  • Structural and Thermoelectric Properties of Nanostructured Nominally Stoichiometric Pb1−x Bi x Te Prepared by Mechanical Alloying

    by Oliver Falkenbach, Marc O. Loeh, Christoph W. Wiegand, Andreas Schmitz, David Hartung, Guenter Koch, Peter J. Klar, Eckhard Mueller, Sabine Schlecht


  • Noble metal‐doping of nanostructured tin(II) sulfide

    by Oliver Falkenbach, Jan Tinz, Anne S. Schulze, Eckhard Mueller, Sabine Schlecht


  • Tin Telluride-Based Nanocomposites of the Type AgSnmBiTe2+m (BTST-m) as Effective Lead-Free Thermoelectric Materials

    by Oliver Falkenbach, Andreas Schmitz, Torben Dankwort, Guenter Koch, Lorenz Kienle, Eckhard Mueller, Sabine Schlecht