Yung Ting
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yung Ting has a total of 74 co-authors. Here are the top co-authors by number of shared publications:
Chun-Chung Li
Chung Yuan Christian University, Chung Li, Taiwan
9 shared publicationsHo-Chin Jar
Department of Mechanical Engineering, Chung Yuan Christian University, No. 200, Chung Pei Rd., Chung Li 32023, Taiwan
8 shared publicationsJeng-Shen Huang
3 shared publicationsShin-Liang Chen
Chung Yuan Christian University, Chung Li, Taiwan, R.O.C.
3 shared publications- Suprapto
Universitas Negeri Medan
3 shared publications Bing-Kuan Hou
Dept. of Mechanical Eng., Chung Yuan Christian Univ., Chung Li 32023, Taiwan#TAB
2 shared publications
Latest Publications
- 20 June 2024
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 141 (35)
Fabrication of PZT/PVDF composite film and the influence of homogeneity to dielectric constant
The Lead Zirconate Titanate/polyvinylidene fluoride (PZT/PVDF) piezoelectric composite with various volume fractions of PZT is successfully fabricated by the proposed solution casting and hot press methods. The aim of this study is to determine the quality of the composite material being fabricated by its homogeneity. Homogeneity can be determined by computing the free path space between particles based on the binary image of SEM, using dispersion and distribution quantitative methods, to gain a comprehensive understanding of the particles' scattering conditions. In comparison to several selected models providing adjustable factors that are highly related to the effect of homogeneity of the composite's internal structure, a suitable model is found.
- 20 June 2024
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 141 (35)
Fabrication of PZT/PVDF composite film and the influence of homogeneity to dielectric constant
The Lead Zirconate Titanate/polyvinylidene fluoride (PZT/PVDF) piezoelectric composite with various volume fractions of PZT is successfully fabricated by the proposed solution casting and hot press methods. The aim of this study is to determine the quality of the composite material being fabricated by its homogeneity. Homogeneity can be determined by computing the free path space between particles based on the binary image of SEM, using dispersion and distribution quantitative methods, to gain a comprehensive understanding of the particles' scattering conditions. In comparison to several selected models providing adjustable factors that are highly related to the effect of homogeneity of the composite's internal structure, a suitable model is found.
- 22 May 2024
- Published by Wiley in Polymer International
- Vol. 73 (9) , 727-747
Fabrication and characterization of PZT / PVDF composite films for force sensor applications
This study explored the impact of hot press parameters on lead zirconate titanate (PZT)/poly(vinylidene fluoride) (PVDF) composite films designed for force‐sensing applications. The systematic fraction (PZT/PVDF), pressure, temperature, and time during hot pressing processes are subject to variation. The focus is on the resulting composite film thickness and its subsequent influence on the piezoelectric properties, which are essential for the performance of force sensors. The present study investigated the characteristics and performance of PZT/PVDF composite films with fraction ratios 2/5, 5/5, and 7/3 and hot pressure of 10, 40, and 60 MPa and temperature at 150 °C for 2 h. The characterization of these films was conducted using X‐ray diffraction, Fourier transform infrared spectroscopy, atomic force microscopy, and scanning electron microscopy. The piezoelectric properties ( d 33 and d 31 ) were measured using impact and extraction tests to evaluate the performance of films with applied forces. The results show that the highest piezoelectric coefficients ( d 33 and d 31 ) were determined to be 35.8 and 12.60 pC N −1 , with fraction ratios of 7/3 and 2/5. The study revealed a positive correlation between the PZT/PVDF ratio and sensitivity, indicating that an increase in the ratio leads to an increase in sensitivity. Conversely, a negative relationship was observed between the impact load and the sensor sensitivity, suggesting that an increase in the impact load results in a sensitivity decrease. The results of this work demonstrate the great potential of piezoelectric PZT/PVDF composite films in force sensors for small load applications. © 2024 Society of Chemical Industry.
- 22 May 2024
- Published by Wiley in Polymer International
- Vol. 73 (9) , 727-747
Fabrication and characterization of PZT / PVDF composite films for force sensor applications
This study explored the impact of hot press parameters on lead zirconate titanate (PZT)/poly(vinylidene fluoride) (PVDF) composite films designed for force‐sensing applications. The systematic fraction (PZT/PVDF), pressure, temperature, and time during hot pressing processes are subject to variation. The focus is on the resulting composite film thickness and its subsequent influence on the piezoelectric properties, which are essential for the performance of force sensors. The present study investigated the characteristics and performance of PZT/PVDF composite films with fraction ratios 2/5, 5/5, and 7/3 and hot pressure of 10, 40, and 60 MPa and temperature at 150 °C for 2 h. The characterization of these films was conducted using X‐ray diffraction, Fourier transform infrared spectroscopy, atomic force microscopy, and scanning electron microscopy. The piezoelectric properties ( d 33 and d 31 ) were measured using impact and extraction tests to evaluate the performance of films with applied forces. The results show that the highest piezoelectric coefficients ( d 33 and d 31 ) were determined to be 35.8 and 12.60 pC N −1 , with fraction ratios of 7/3 and 2/5. The study revealed a positive correlation between the PZT/PVDF ratio and sensitivity, indicating that an increase in the ratio leads to an increase in sensitivity. Conversely, a negative relationship was observed between the impact load and the sensor sensitivity, suggesting that an increase in the impact load results in a sensitivity decrease. The results of this work demonstrate the great potential of piezoelectric PZT/PVDF composite films in force sensors for small load applications. © 2024 Society of Chemical Industry.
- 14 July 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
- Vol. 69 (9) , 2696-2702
Using a Traveling-Wave Piezoelectric Device to Generate a Liquid Wave for Efficient Lightweight Particle Transfer
In this study, the transfer process of extremely light and small-sized particles along a defined direction without flipping them over on the transportation surface is evaluated by using a traveling wave. For this, the use of a liquid, as the contact layer injected onto the top surface of a piezoelectric traveling-wave device, is proposed to transmit the wave into the particles. As a preload is unlikely to be assigned here, the adhesion force between the lightweight particle and the liquid is expected to dominate the delivery effect. A short-beam linear motor is chosen as an example of a piezoelectric device that can generate a traveling wave in association with several selected liquids such as water, saline water, oil, and glycerol. The influence on the traveling-wave amplitude transmitted to liquids with different viscosities and heights is studied by an analytical approach and the finite-element simulation. The surface energy theory is used to determine the adhesion force between the liquid and the lightweight particle. An experiment is conducted to measure the speed of particles with variable sizes that are transported by the liquid wave. The analytical and experimental results are in good agreement, verifying the influence of the above concerned factors on the particle transfer speed.
- 14 July 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
- Vol. 69 (9) , 2696-2702
Using a Traveling-Wave Piezoelectric Device to Generate a Liquid Wave for Efficient Lightweight Particle Transfer
In this study, the transfer process of extremely light and small-sized particles along a defined direction without flipping them over on the transportation surface is evaluated by using a traveling wave. For this, the use of a liquid, as the contact layer injected onto the top surface of a piezoelectric traveling-wave device, is proposed to transmit the wave into the particles. As a preload is unlikely to be assigned here, the adhesion force between the lightweight particle and the liquid is expected to dominate the delivery effect. A short-beam linear motor is chosen as an example of a piezoelectric device that can generate a traveling wave in association with several selected liquids such as water, saline water, oil, and glycerol. The influence on the traveling-wave amplitude transmitted to liquids with different viscosities and heights is studied by an analytical approach and the finite-element simulation. The surface energy theory is used to determine the adhesion force between the liquid and the lightweight particle. An experiment is conducted to measure the speed of particles with variable sizes that are transported by the liquid wave. The analytical and experimental results are in good agreement, verifying the influence of the above concerned factors on the particle transfer speed.
- 1 December 2021
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 332
Design and performance evaluation of a multi-axis thin-film sensor for milling process measurement
- 1 December 2021
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 332
Design and performance evaluation of a multi-axis thin-film sensor for milling process measurement
- 22 November 2021
- Published by Taylor & Francis in Integrated Ferroelectrics
- Vol. 221 (1) , 73-87
Effect and Evaluation of an Ultrasonic Atomizer With Large Vibration Amplitude
An ultrasonic atomizer can produce large vibration amplitude is designed. Different from the structure of the usually seen ultrasonic spray nozzle, the atomizer is fundamentally constructed with a hollow tube encircled with several pieces of sectional type piezoelectric actuators, which can radially oscillate the tube to generate desired vibration profile. Atomization is formed on the surface around the liquid outlet of the tube where maximum vibration amplitude occurs. In search of resonance frequency and vibration amplitude, modal and harmonic analyses of the ultrasonic atomizer are carried out by ANSYS. In comparison the simulated results with the experimental results, both are in good agreement. A measurement system is set up for detecting the atomization droplets and calculating the droplet size and distribution. An attempt is to design an ultrasonic atomizer can produce high distribution and small diameter droplets for some application-level requirements, droplet diameter around 20–60 μm is assumed to be the specification for performance verification of the proposed atomizer. In experiment, it is found nearly 90% of atomized droplets fit for the requirement. Besides the most important factor of operating frequency, a relation of amplitude is found to include in the well-known Lang and Rayleigh’s equation.
- 22 November 2021
- Published by Taylor & Francis in Integrated Ferroelectrics
- Vol. 221 (1) , 73-87
Effect and Evaluation of an Ultrasonic Atomizer With Large Vibration Amplitude
An ultrasonic atomizer can produce large vibration amplitude is designed. Different from the structure of the usually seen ultrasonic spray nozzle, the atomizer is fundamentally constructed with a hollow tube encircled with several pieces of sectional type piezoelectric actuators, which can radially oscillate the tube to generate desired vibration profile. Atomization is formed on the surface around the liquid outlet of the tube where maximum vibration amplitude occurs. In search of resonance frequency and vibration amplitude, modal and harmonic analyses of the ultrasonic atomizer are carried out by ANSYS. In comparison the simulated results with the experimental results, both are in good agreement. A measurement system is set up for detecting the atomization droplets and calculating the droplet size and distribution. An attempt is to design an ultrasonic atomizer can produce high distribution and small diameter droplets for some application-level requirements, droplet diameter around 20–60 μm is assumed to be the specification for performance verification of the proposed atomizer. In experiment, it is found nearly 90% of atomized droplets fit for the requirement. Besides the most important factor of operating frequency, a relation of amplitude is found to include in the well-known Lang and Rayleigh’s equation.
- 26 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
- Vol. 68 (8) , 2815-2823
Design of a Short-Beam Linear Traveling-Wave Piezoelectric Motor
A straight short-beam linear piezoelectric motor constructed with two sets of ceramic actuators separated with the 1/4 wavelength interval is designed in this article. The piezoelectric ceramic actuators are fabricated in the whole body, which is driven by a two-phase circuit with the same amplitude but a phase difference of π/4. Traveling wave (TW) is formed by superimposing standing waves generated by each set of ceramic actuators. At the ends of the short beam, a wave-reduction mechanism with larger cross-sectional area is designed so that wave reflection is effectively diminished to preserve the TW. The currently developed short-beam linear piezoelectric motor is estimated, which can produce an ideal output speed of 169 mm/s while applying voltage of V pp = 300 V at 45.49 kHz. Instead of operating as a stator to drive a carriage for example, the short-beam linear piezoelectric motor is implemented on a guide slider, and therefore, a linear piezoelectric motor stage is built. While driving the linear stage employed with a preload 300 GW and a friction coefficient of about 0.15, the propulsion force is measured about 4.8 N, the speed is about 56 mm/s, and the position resolution can achieve in the submicrometer scale.
- 26 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
- Vol. 68 (8) , 2815-2823
Design of a Short-Beam Linear Traveling-Wave Piezoelectric Motor
A straight short-beam linear piezoelectric motor constructed with two sets of ceramic actuators separated with the 1/4 wavelength interval is designed in this article. The piezoelectric ceramic actuators are fabricated in the whole body, which is driven by a two-phase circuit with the same amplitude but a phase difference of π/4. Traveling wave (TW) is formed by superimposing standing waves generated by each set of ceramic actuators. At the ends of the short beam, a wave-reduction mechanism with larger cross-sectional area is designed so that wave reflection is effectively diminished to preserve the TW. The currently developed short-beam linear piezoelectric motor is estimated, which can produce an ideal output speed of 169 mm/s while applying voltage of V pp = 300 V at 45.49 kHz. Instead of operating as a stator to drive a carriage for example, the short-beam linear piezoelectric motor is implemented on a guide slider, and therefore, a linear piezoelectric motor stage is built. While driving the linear stage employed with a preload 300 GW and a friction coefficient of about 0.15, the propulsion force is measured about 4.8 N, the speed is about 56 mm/s, and the position resolution can achieve in the submicrometer scale.
- Open Access
Using Annealing Treatment on Fabrication Ionic Liquid-Based PVDF Films
In this study, a simple method to obtain pure β-phase directly from the melt process is proposed. A series of PVDF and ionic liquid (IL) was prepared by a solvent casting method with appropriate associated with the subsequent annealing treatment. IL plays a role of filler, which can create strong electrostatic interaction with PVDF matrix and directly induce β-phase crystallization on the PVDF during the melt. PVDF film sample is immersed in hot water for annealing treatment at different temperatures (25 °C to 70 °C). We found that annealing in high temperatures especially can not only increase more IL inserted into the amorphous region of polymer matrix to make more phase transformation, but also accelerate IL removal. Characteristics and performance of the PVDF films were investigated by use of FTIR, XRD, SEM, and AFM. Piezoelectric coefficient d33 as well as d31, degree of crystallinity, and sensitivity are measured in experiment to verify the performance of PVDF film.
Open AccessUsing Annealing Treatment on Fabrication Ionic Liquid-Based PVDF Films
In this study, a simple method to obtain pure β-phase directly from the melt process is proposed. A series of PVDF and ionic liquid (IL) was prepared by a solvent casting method with appropriate associated with the subsequent annealing treatment. IL plays a role of filler, which can create strong electrostatic interaction with PVDF matrix and directly induce β-phase crystallization on the PVDF during the melt. PVDF film sample is immersed in hot water for annealing treatment at different temperatures (25 °C to 70 °C). We found that annealing in high temperatures especially can not only increase more IL inserted into the amorphous region of polymer matrix to make more phase transformation, but also accelerate IL removal. Characteristics and performance of the PVDF films were investigated by use of FTIR, XRD, SEM, and AFM. Piezoelectric coefficient d33 as well as d31, degree of crystallinity, and sensitivity are measured in experiment to verify the performance of PVDF film.
- Open Access
- 18 June 2018
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 10 (6)
Design and performance evaluation of an exponentially weighted moving average–based adaptive control for piezo-driven motion platform
In this article, building a controlled system with velocity feedback in the inner loop for a platform driven by piezoelectric motors is investigated. Such a motion control system is subject to disturbance such as friction, preload, and temperature rise in operation. Especially, temperature rise is an essential problem of using piezoelectric motor, but very few research works address this topic in depth. Exponentially weighted moving average method has been widely used in process control to deal with systematic change and drift disturbance. It is attempted to map the exponentially weighted moving average method and the predictor corrector control with two exponentially weighted moving average formulas into a run-to-run model reference adaptive system for velocity control. Using a predictive friction model, a dead-zone compensator is built that can reduce the friction effect and provide an approximately linear relation of the input voltage and the output velocity for the subsequent exponentially weighted moving average or predictor corrector control control design. Comparison of the exponentially weighted moving average, predictor corrector control, and proportional–integral–derivative controllers is carried out in experiment with different speed patterns on a single-axis and a bi-axial platform. The results indicate that the proposed run-to-run-model reference adaptive system predictor corrector control is superior to the other methods.
- 18 June 2018
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 10 (6)
Open AccessDesign and performance evaluation of an exponentially weighted moving average–based adaptive control for piezo-driven motion platform
In this article, building a controlled system with velocity feedback in the inner loop for a platform driven by piezoelectric motors is investigated. Such a motion control system is subject to disturbance such as friction, preload, and temperature rise in operation. Especially, temperature rise is an essential problem of using piezoelectric motor, but very few research works address this topic in depth. Exponentially weighted moving average method has been widely used in process control to deal with systematic change and drift disturbance. It is attempted to map the exponentially weighted moving average method and the predictor corrector control with two exponentially weighted moving average formulas into a run-to-run model reference adaptive system for velocity control. Using a predictive friction model, a dead-zone compensator is built that can reduce the friction effect and provide an approximately linear relation of the input voltage and the output velocity for the subsequent exponentially weighted moving average or predictor corrector control control design. Comparison of the exponentially weighted moving average, predictor corrector control, and proportional–integral–derivative controllers is carried out in experiment with different speed patterns on a single-axis and a bi-axial platform. The results indicate that the proposed run-to-run-model reference adaptive system predictor corrector control is superior to the other methods.
- 14 June 2018
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 135 (36)
Characteristic analysis of biaxially stretched PVDF thin films
By use of biaxial stretching process of poly(vinylidene fluoride) fabrication to gain high piezoelectricity is the focus in this article. The influence of different stretch ratio and temperature are investigated and compared to uniaxial stretching process. The Fourier transform infrared spectroscopy and X‐ray diffraction are used to observe the β‐phase fraction and the degree of crystallinity. The piezoelectric coefficients (d33, d31) and the sensitivity are also measured. All the above characteristic examinations show the same consequences that equi‐biaxial stretching process employed with same stretch ratio in both axial directions of poly(vinylidene fluoride) fabrication is the focus in this article. And heating temperature would have adequate piezoelectricity approximate to uniaxial stretching. In observation of surface morphology by using scanning electron microscopy, uniformity in biaxial direction is gained. However, biaxial stretching with higher stretch ratio of R = 4 × 4 would produce porosity and crack. Via atomic force microscopy, biaxial stretching with higher stretch ratio attains better surface chain orientation and smoothness. To sum up, the biaxial stretching approach has the advantage of low stretch ratio requirement to preserve good fabrication quality. Set up with stretch ratio in‐between R = 3 × 3 and R = 4 × 4 at 80 °C is suggested to use in biaxial stretching. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018, 135, 46677.
- 14 June 2018
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 135 (36)
Characteristic analysis of biaxially stretched PVDF thin films
By use of biaxial stretching process of poly(vinylidene fluoride) fabrication to gain high piezoelectricity is the focus in this article. The influence of different stretch ratio and temperature are investigated and compared to uniaxial stretching process. The Fourier transform infrared spectroscopy and X‐ray diffraction are used to observe the β‐phase fraction and the degree of crystallinity. The piezoelectric coefficients (d33, d31) and the sensitivity are also measured. All the above characteristic examinations show the same consequences that equi‐biaxial stretching process employed with same stretch ratio in both axial directions of poly(vinylidene fluoride) fabrication is the focus in this article. And heating temperature would have adequate piezoelectricity approximate to uniaxial stretching. In observation of surface morphology by using scanning electron microscopy, uniformity in biaxial direction is gained. However, biaxial stretching with higher stretch ratio of R = 4 × 4 would produce porosity and crack. Via atomic force microscopy, biaxial stretching with higher stretch ratio attains better surface chain orientation and smoothness. To sum up, the biaxial stretching approach has the advantage of low stretch ratio requirement to preserve good fabrication quality. Set up with stretch ratio in‐between R = 3 × 3 and R = 4 × 4 at 80 °C is suggested to use in biaxial stretching. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018, 135, 46677.
- 2 January 2015
- Published by Taylor & Francis in Ferroelectrics
- Vol. 474 (1) , 169-178
Multi-mode Control in a Two-stage Piezoelectric Transducer for an Application of Physical Therapy
- 2 January 2015
- Published by Taylor & Francis in Ferroelectrics
- Vol. 474 (1) , 169-178
Multi-mode Control in a Two-stage Piezoelectric Transducer for an Application of Physical Therapy