Jong Sun Choi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jong Sun Choi has a total of 46 co-authors. Here are the top co-authors by number of shared publications:
- Jaehoon Park
School of Semiconductor and Display Technology, Hallym University, Chun-Choen 24252, Republic of Korea
10 shared publications Dong Wook Kim
Hongik University
4 shared publications- Jin-Hyuk Bae
Kyungpook National University
3 shared publications Lee-Mi Do
IT Convergence Technology Research Laboratory, Electronics and Telecommunications Research Institute, Daejeon 305-700, Korea
2 shared publications- Sin-Doo Lee
Seoul National Univ. (Korea, Republic of)
2 shared publications - Bokyung Kim
Department of Electronic Engineering, Hallym University, Chuncheon 24252, Korea
1 shared publication
Latest Publications
- Open Access
Atomic Structure Evaluation of Solution-Processed a-IZO Films and Electrical Behavior of a-IZO TFTs
Understanding the chemical reaction pathway of the metal–salt precursor is essential for modifying the properties of solution-processed metal-oxide thin films and further improving their electrical performance. In this study, we focused on the structural growth of solution-processed amorphous indium-zinc-oxide (a-IZO) films and the electrical behavior of a-IZO thin-film transistors (TFT). To this end, solution-processed a-IZO films were prepared with respect to the Zn molar ratio, and their structural characteristics were analyzed. For the structural characteristic analysis of the a-IZO film, the cross-section, morphology, crystallinity, and atomic composition characteristics were used as the measurement results. Furthermore, the chemical reaction pathway of the nitrate precursor-based IZO solution was evaluated for the growth process of the a-IZO film structure. These interpretations of the growth process and chemical reaction pathway of the a-IZO film were assumed to be due to the thermal decomposition of the IZO solution and the structural rearrangement after annealing. Finally, based on the structural/chemical results, the electrical performance of the fabricated a-IZO TFT depending on the Zn concentration was evaluated, and the electrical behavior was discussed in relation to the structural characteristics.
Open AccessAtomic Structure Evaluation of Solution-Processed a-IZO Films and Electrical Behavior of a-IZO TFTs
Understanding the chemical reaction pathway of the metal–salt precursor is essential for modifying the properties of solution-processed metal-oxide thin films and further improving their electrical performance. In this study, we focused on the structural growth of solution-processed amorphous indium-zinc-oxide (a-IZO) films and the electrical behavior of a-IZO thin-film transistors (TFT). To this end, solution-processed a-IZO films were prepared with respect to the Zn molar ratio, and their structural characteristics were analyzed. For the structural characteristic analysis of the a-IZO film, the cross-section, morphology, crystallinity, and atomic composition characteristics were used as the measurement results. Furthermore, the chemical reaction pathway of the nitrate precursor-based IZO solution was evaluated for the growth process of the a-IZO film structure. These interpretations of the growth process and chemical reaction pathway of the a-IZO film were assumed to be due to the thermal decomposition of the IZO solution and the structural rearrangement after annealing. Finally, based on the structural/chemical results, the electrical performance of the fabricated a-IZO TFT depending on the Zn concentration was evaluated, and the electrical behavior was discussed in relation to the structural characteristics.
- 22 January 2019
- Published by Taylor & Francis in Molecular Crystals and Liquid Crystals
- Vol. 679 (1) , 1-7
Electrical characteristics of a 6,13-Bis(triisopropylsilylethynyl)pentacene thin-film transistor under light absorption
The electrical properties of solution-processed 6,13-bis(triisopropylsilylethynyl)pentacene thin-film transistors were investigated under various light irradiation wavelengths. Irradiated light conditions were determined from wavelengths with specific peaks in the absorbance spectrum of the film, and changes in electrical characteristics were analyzed under light irradiation at these wavelengths. At long wavelengths of 695, 640, and 585 nm, a small number of photo-generated excitons lowered the hole injection barrier. At short wavelengths of 450 and 340 nm, a large number of photo-generated excitons threatened the electrically accumulated holes, lowering the decrease in threshold voltage variation. Furthermore, results including the content of the films based on light intensity, according to irradiated wavelengths are presented.
- 22 January 2019
- Published by Taylor & Francis in Molecular Crystals and Liquid Crystals
- Vol. 679 (1) , 1-7
Electrical characteristics of a 6,13-Bis(triisopropylsilylethynyl)pentacene thin-film transistor under light absorption
The electrical properties of solution-processed 6,13-bis(triisopropylsilylethynyl)pentacene thin-film transistors were investigated under various light irradiation wavelengths. Irradiated light conditions were determined from wavelengths with specific peaks in the absorbance spectrum of the film, and changes in electrical characteristics were analyzed under light irradiation at these wavelengths. At long wavelengths of 695, 640, and 585 nm, a small number of photo-generated excitons lowered the hole injection barrier. At short wavelengths of 450 and 340 nm, a large number of photo-generated excitons threatened the electrically accumulated holes, lowering the decrease in threshold voltage variation. Furthermore, results including the content of the films based on light intensity, according to irradiated wavelengths are presented.
- 10 January 2015
- Published by Springer Nature in Electronic Materials Letters
- Vol. 11 (1) , 82-87
Rapid curing of solution-processed zinc oxide films by pulse-light annealing for thin-film transistor applications
- 10 January 2015
- Published by Springer Nature in Electronic Materials Letters
- Vol. 11 (1) , 82-87
Rapid curing of solution-processed zinc oxide films by pulse-light annealing for thin-film transistor applications
- 24 July 2014
- Published by Taylor & Francis in Molecular Crystals and Liquid Crystals
- Vol. 598 (1) , 129-134
Effects of Polystyrene Gate Dielectrics with Various Molecular Weights on Electrical Characteristics of Pentacene Thin-Film Transistors
- 24 July 2014
- Published by Taylor & Francis in Molecular Crystals and Liquid Crystals
- Vol. 598 (1) , 129-134
Effects of Polystyrene Gate Dielectrics with Various Molecular Weights on Electrical Characteristics of Pentacene Thin-Film Transistors
- 17 September 2012
- Published by Taylor & Francis in Molecular Crystals and Liquid Crystals
- Vol. 567 (1) , 50-56
Effects of the Surface Wettability of a Polymeric Insulator in a Solution-Processed Organic Transistor
We investigated the effects of the surface wettability of two polymeric insulators in a 6,13-bis(triisopropylsilylethynyl)-pentacene (TIPS-pentacene) thin-film transistor (TFT). The chemical solvent of TIPS-pentacene was more wettable on a poly(4-vinylphenol) (PVP) insulator than on a poly(vinylidenefluoride-trifluoroethylene) (PVDF-TrFE) insulator. TIPS-pentacene molecules formed large crystals on the PVDF-TrFE layer, resulting in high field-effect mobility for the TFT. In contrast, for the PVP case, the mobility largely varied with the processing temperature of a TIPS-pentacene film. These results demonstrate that the surface wettability of an insulator is important for the crystallization of a solution-processed organic semiconductor and the resulting TFT performance.
- 17 September 2012
- Published by Taylor & Francis in Molecular Crystals and Liquid Crystals
- Vol. 567 (1) , 50-56
Effects of the Surface Wettability of a Polymeric Insulator in a Solution-Processed Organic Transistor
We investigated the effects of the surface wettability of two polymeric insulators in a 6,13-bis(triisopropylsilylethynyl)-pentacene (TIPS-pentacene) thin-film transistor (TFT). The chemical solvent of TIPS-pentacene was more wettable on a poly(4-vinylphenol) (PVP) insulator than on a poly(vinylidenefluoride-trifluoroethylene) (PVDF-TrFE) insulator. TIPS-pentacene molecules formed large crystals on the PVDF-TrFE layer, resulting in high field-effect mobility for the TFT. In contrast, for the PVP case, the mobility largely varied with the processing temperature of a TIPS-pentacene film. These results demonstrate that the surface wettability of an insulator is important for the crystallization of a solution-processed organic semiconductor and the resulting TFT performance.
- Open Access
- 1 September 2012
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 51 (9) , 09MJ01
An Experimental Study of the Effects of Source/Drain to Gate Overlap in Pentacene Thin-Film Transistors
The effects of the source/drain (S/D) to gate overlap on the electrical characteristics of pentacene organic thin-film transistors (OTFTs) are reported. The S/D to gate overlap dimension was varied by adjusting the gate width, while the channel length and width were fixed. The threshold voltage was found to decrease on increasing the overlap dimension; in contrast, the field-effect mobility increased. These characteristic variations are explained on aspects of charge injection and transport properties in pentacene OTFTs, due to the presence of S/D to gate overlaps. The results demonstrate the significant effect of the overlap on the OTFT performance.
- 1 September 2012
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 51 (9) , 09MJ01
Open AccessAn Experimental Study of the Effects of Source/Drain to Gate Overlap in Pentacene Thin-Film Transistors
The effects of the source/drain (S/D) to gate overlap on the electrical characteristics of pentacene organic thin-film transistors (OTFTs) are reported. The S/D to gate overlap dimension was varied by adjusting the gate width, while the channel length and width were fixed. The threshold voltage was found to decrease on increasing the overlap dimension; in contrast, the field-effect mobility increased. These characteristic variations are explained on aspects of charge injection and transport properties in pentacene OTFTs, due to the presence of S/D to gate overlaps. The results demonstrate the significant effect of the overlap on the OTFT performance.
- 1 August 2012
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 51 (8) , 081301
Characteristic Variations of Graphene Field-Effect Transistors Induced by CF4Gas
The influence of tetrafluoromethane (CF4) gas on the electrical characteristics of monolithic graphene field-effect transistors (FETs) is reported. Compared with the results in nitrogen ambient, FETs in CF4 ambient exhibit a positive shift in the Dirac point voltage and an increase in drain current. These changes are ascribed to the electronegative nature of the fluorine atoms in CF4 gas, which is found to induce p-type doping and excess charge carriers in graphene. The electrical response to CF4 gas exposure demonstrates the feasibility of using monolithic graphene FETs as chemical sensors.
- 1 August 2012
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 51 (8) , 081301
Characteristic Variations of Graphene Field-Effect Transistors Induced by CF4Gas
The influence of tetrafluoromethane (CF4) gas on the electrical characteristics of monolithic graphene field-effect transistors (FETs) is reported. Compared with the results in nitrogen ambient, FETs in CF4 ambient exhibit a positive shift in the Dirac point voltage and an increase in drain current. These changes are ascribed to the electronegative nature of the fluorine atoms in CF4 gas, which is found to induce p-type doping and excess charge carriers in graphene. The electrical response to CF4 gas exposure demonstrates the feasibility of using monolithic graphene FETs as chemical sensors.
- Open Access
Effects of Interfacial Charge Depletion in Organic Thin-Film Transistors with Polymeric Dielectrics on Electrical Stability
We investigated the electrical stabilities of two types of pentacene-based organic thin-film transistors (OTFTs) with two different polymeric dielectrics: polystyrene (PS) and poly(4-vinyl phenol) (PVP), in terms of the interfacial charge depletion. Under a short-term bias stress condition, the OTFT with the PVP layer showed a substantial increase in the drain current and a positive shift of the threshold voltage, while the PS layer case exhibited no change. Furthermore, a significant increase in the off-state current was observed in the OTFT with the PVP layer which has a hydroxyl group. In the presence of the interfacial hydroxyl group in PVP, the holes are not fully depleted during repetitive operation of the OTFT with the PVP layer and a large positive gate voltage in the off-state regime is needed to effectively refresh the electrical characteristics. It is suggested that the depletion-limited holes at the interface, i.e., interfacial charge depletion, between the PVP layer and the pentacene layer play a critical role on the electrical stability during operation of the OTFT.
Open AccessEffects of Interfacial Charge Depletion in Organic Thin-Film Transistors with Polymeric Dielectrics on Electrical Stability
We investigated the electrical stabilities of two types of pentacene-based organic thin-film transistors (OTFTs) with two different polymeric dielectrics: polystyrene (PS) and poly(4-vinyl phenol) (PVP), in terms of the interfacial charge depletion. Under a short-term bias stress condition, the OTFT with the PVP layer showed a substantial increase in the drain current and a positive shift of the threshold voltage, while the PS layer case exhibited no change. Furthermore, a significant increase in the off-state current was observed in the OTFT with the PVP layer which has a hydroxyl group. In the presence of the interfacial hydroxyl group in PVP, the holes are not fully depleted during repetitive operation of the OTFT with the PVP layer and a large positive gate voltage in the off-state regime is needed to effectively refresh the electrical characteristics. It is suggested that the depletion-limited holes at the interface, i.e., interfacial charge depletion, between the PVP layer and the pentacene layer play a critical role on the electrical stability during operation of the OTFT.
- 18 June 2009
- Published by Taylor & Francis in Molecular Crystals and Liquid Crystals
- Vol. 505 (1) , 104/[342]-110/[348]
Condensation and Annealing Effects of Polymer Gate Insulator on Organic Thin-Film Transistor Characteristics
Performances of organic thin-film transistors (TFTs) can be detrimentally affected by the state of gate dielectric layer. In this study, we report the condensation and annealing effects of a polymer gate dielectric layer. For the observations of the effect of condensation, the spin-coated polymer layers with various deposition conditions were fabricated and kept under low vacuum condition for several days. It is observed that the thickness of polymer layer and the electrical characteristics of organic TFTs vary with the condensation time, and the appropriate additional annealing process could stabilize the gate dielectric layer and even improve the device characteristics consequently.
- 18 June 2009
- Published by Taylor & Francis in Molecular Crystals and Liquid Crystals
- Vol. 505 (1) , 104/[342]-110/[348]
Condensation and Annealing Effects of Polymer Gate Insulator on Organic Thin-Film Transistor Characteristics
Performances of organic thin-film transistors (TFTs) can be detrimentally affected by the state of gate dielectric layer. In this study, we report the condensation and annealing effects of a polymer gate dielectric layer. For the observations of the effect of condensation, the spin-coated polymer layers with various deposition conditions were fabricated and kept under low vacuum condition for several days. It is observed that the thickness of polymer layer and the electrical characteristics of organic TFTs vary with the condensation time, and the appropriate additional annealing process could stabilize the gate dielectric layer and even improve the device characteristics consequently.
- 4 September 2007
- Published by Taylor & Francis in Molecular Crystals and Liquid Crystals
- Vol. 471 (1) , 173-179
Effect of Surfactant on Preparation of Poly(4-Vinylphenol)/Titanium Dioxide Composite for a Gate Insulator of Organic Thin Film Transistors
Composite materials of poly(4-vinylphenol) (PVP) and titanium dioxide (TiO2) nanoparticles were fabricated via a spin coating process in order to enhance dielectric properties for a gate insulator application of the OTFT in this study. In order to improve dispersion stability of the TiO2 nanoparticles in the polymeric solution during the process, a surfactant was also adopted onto the solution mixture. The dispersion property was observed by measuring sedimentation time of TiO2 particles in the polymeric solution, and the effect of surfactant on the surface morphology of the dielectric layer was further analyzed by using atomic force microscopy. Dielectric properties of the PVP-TiO2 composite and performance of OTFTs with the PVP-TiO2 composite insulator are presented, along with their effects on device performance with pentacene layer as a semiconductor.
- 4 September 2007
- Published by Taylor & Francis in Molecular Crystals and Liquid Crystals
- Vol. 471 (1) , 173-179
Effect of Surfactant on Preparation of Poly(4-Vinylphenol)/Titanium Dioxide Composite for a Gate Insulator of Organic Thin Film Transistors
Composite materials of poly(4-vinylphenol) (PVP) and titanium dioxide (TiO2) nanoparticles were fabricated via a spin coating process in order to enhance dielectric properties for a gate insulator application of the OTFT in this study. In order to improve dispersion stability of the TiO2 nanoparticles in the polymeric solution during the process, a surfactant was also adopted onto the solution mixture. The dispersion property was observed by measuring sedimentation time of TiO2 particles in the polymeric solution, and the effect of surfactant on the surface morphology of the dielectric layer was further analyzed by using atomic force microscopy. Dielectric properties of the PVP-TiO2 composite and performance of OTFTs with the PVP-TiO2 composite insulator are presented, along with their effects on device performance with pentacene layer as a semiconductor.