MSMakoto Shiojiri

Makoto Shiojiri

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Makoto Shiojiri has a total of 36 co-authors. Here are the top co-authors by number of shared publications:

  • Masahiro Kawasaki

    Department of Intelligent Interaction Technologies, Institute of Systems and Information Engineering, University of Tsukuba, Tsukuba, Japan

    6 shared publications
  • Jer-Ren Yang

    Department of Materials Science and Engineering, National Taiwan University, Taipei, Taiwan

    4 shared publications
  • Masateru Nose

    Faculty of Art and Design,University of Toyama,Takaoka 933-8588,Japan

    4 shared publications
  • Ichiro Onishi

    JEOL Ltd.,3-1-2 Musashino,Akishima,Tokyo 196-8558,Japan

    3 shared publications
  • H. L. Tsai

    National Taiwan University Institute of Materials Science and Engineering Taipei, Taiwan 106, Republic of China

    2 shared publications
  • J. T. Hsu

    Industrial Technology Research Institute Electronics and Optoelectronics Research Laboratories Hsinchu, Taiwan 310, Republic of China

    2 shared publications

Latest Publications

  • Structural investigations on green culms and charcoal of Bambusa multiplex

    by Visittapong Yordsri, Chanchana Thanachayanont, Chabaiporn Junin, Masahiro Kawasaki, Shunsuke Asahina, Tetsuo Oikawa, Atsushi Saiki, Tadashi Nobuchi, Makoto Shiojiri

    Green culms of Bambusa multiplex and the bamboo charcoal carbonized from the green culms at 700°C have been studied by means of X‐ray diffraction, X‐ray fluorescent element analysis, analytical scanning electron microscopy, and analytical scanning transmission electron microscopy (STEM), aiming at industrial applications as raw materials for functional devices and substances. It is revealed that the green culms and the charcoal contain a significant amount of Si, in particular, ∼18 wt % in the skin. The green culms comprise amorphous and crystalline celluloses. The charcoal has a so‐called amorphous structure which is composed of randomly distributed carbon nanotubes and fibers. The growth of Ag‐doped activated charcoal powders that were produced by two different methods using this charcoal powder has also been studied.


  • Structural Investigation of AlN/SiOx Nanocomposite Hard Coatings Fabricated by Differential Pumping Cosputtering

    by Masahiro Kawasaki, Masateru Nose, Ichiro Onishi, Makoto Shiojiri

    AlN/SiOx nanocomposite coatings fabricated by differential pumping cosputtering (DPCS) were investigated by analytical electron microscopy. The DPCS system consists of two halves of a Chamber, A and B, for radio frequency (RF) magnetron sputtering deposition of different materials, and a substrate holder that rotates through the chambers. Al and SiO2 were sputtered in gas environments with a flow mixture of N2 and Ar gases at RF power of 200 W in the Al Chamber A and a flow of Ar gas at RF powers of 49 W in the SiO2 Chamber B. The substrates of (001) Si wafers heated at 250°C were rotated for 1,080 min at 3 rpm and alternately deposited by AlN and SiO2. AlN columnar crystals grew at a rate of ~0.3 nm/revolution preferentially along the hexagonal [0001] axis. Amorphous silicon oxide (a-SiOx), deposited at a rate of ~0.2 nm/revolution, was coagulated preferentially along the boundaries between the AlN columns and also the interfaces between the subgrains within the AlN columns. The a-SiOx played an important role in the increase in mechanical hardness of the AlN/SiOx composite coating by disturbing deformation of AlN crystal lattices.


  • Structure and biomechanics of culms of Phragmites australis used for reeds of Japanese wind instrument “hichiriki”

    by Masahiro Kawasaki, Tadashi Nobuchi, Yuta Nakafushi, Masateru Nose, Makoto Shiojiri

    Hichiriki is a traditional Japanese double‐reed wind instrument used in Japanese ancient imperial court music, gagaku, which has been performed since the 7th century. The best reeds for hichiriki have been made of culms or stems of Phragmites australis (P. australis) that are harvested from only a limited reed bed at Udono near Kyoto. The aim of this study is to elucidate why the stems from Udono are the best materials for hichiriki reeds. Plant anatomy was examined for choice stems of P. australis grown in different reed beds in Japan as well as morphology, and the local indentation hardness and Young's modulus of tissues on the cross‐sections of some representatives of hichiriki reeds were measured. It is concluded that the good stems for hichiriki reeds have an outer diameter of about 11 mm, a wall thickness of about 1 mm and comparatively homogeneous structure where harder materials, such as epidermis, hypodermis, sclerenchymatous cells, and vascular bundle sheaths with hard walls, are orderly deployed with softer materials such as parenchyma cells and vascular bundles. This structure has smaller differences of hardness and Young's modulus between the hard and soft materials in the reed, providing the best music performance. Microsc. Res. Tech. 78:260–267, 2015.


  • Structure of multilayered Cr(Al)N/SiOx nanocomposite coatings fabricated by differential pumping co-sputtering

    by Masahiro Kawasaki, Masateru Nose, Ichiro Onishi, Makoto Shiojiri

    A Cr(Al)N/38 vol. % SiOx hard coating was prepared on a (001) Si substrate at 250 °C in a differential pumping co-sputtering system, which has two chambers for radio frequency (RF) sputtering and a substrate holder rotating on the chambers. The composite coating was grown by alternate sputter-depositions from CrAl and SiO2 targets with flows of N2+Ar and Ar at RF powers of 200 and 75 W, respectively, on transition layers grown on the substrate. Analytical electron microscopy reveled that the Cr(Al)N/SiOx coating had a multilayered structure of Cr(Al)N crystal layers ∼1.6 nm thick and two-dimensionally dispersed amorphous silicon oxide (a-SiOx) particles with sizes of ∼1 nm or less. The a-SiOx particles were enclosed with the Cr(Al)N layers. The coating had a low indentation hardness of ∼25 GPa at room temperature, due to a high oxide fraction of 38 vol. % and a low substrate rotational speed of 1 rpm. Faster rotation and lower oxide fraction would make a-SiOx particles smaller, resulting in the formation of Cr(Al)N crystal including the very fine a-SiOx particles with small number density. They would work as obstacles for the lattice deformation of the Cr(Al)N crystals. We have fabricated a superhard coating of Cr(Al)N/17 vol. % SiOx with a hardness of 46 GPa prepared at 12 rpm.


  • Open Access

    Photonic Crystal Structure and Coloration of Wing Scales of Butterflies Exhibiting Selective Wavelength Iridescence

    by Filip Mika, Jiřina Matějková-Plšková, Suratwadee Jiwajinda, Punyavee Dechkrong, Makoto Shiojiri

    The coloration of butterflies that exhibit human visible iridescence from violet to green has been elucidated. Highly tilted multilayers of cuticle on the ridges, which were found in the scales of male S. charonda and E. mulciber butterflies, produce a limited-view, selective wavelength iridescence (ultraviolet (UV)~green) as a result of multiple interference between the cuticle-air layers. The iridescence from C. ataxus originates from multilayers in the groove plates between the ridges and ribs. The interference takes place between the top and bottom surfaces of each layer and incoherently between different layers. Consequently, the male with the layers that are ~270 nm thick reflects light of UV~560 nm (green) and the female with the layers that are ~191 nm thick reflects light of UV~400 nm (violet). T. aeacus does not produce the iridescent sheen which T. magellanus does. No iridescent sheen is ascribed to microrib layers, which are perpendicular to the scale plane, so that they cannot reflect any backscattering. The structures of these butterflies would provide us helpful hints to manipulate light in photoelectric devices, such as blue or UV LEDs.


  • Amplified Spontaneous Emission From ZnO in n-ZnO/p-GaN Heterojunction Light-Emitting Diodes With an External-Feedback Reflector

    by Hsing-Chao Chen, Miin-Jang Chen, Yung-Chen Cheng, Jer-Ren Yang, Makoto Shiojiri

    The effect of external feedback on the ultraviolet electroluminescence (EL) from n-ZnO/p-GaN heterojunction light-emitting diodes at room temperature was studied. Atomic layer deposition was used to grow the high-quality n-type ZnO epilayer, and the p-type GaN was prepared by metal-organic chemical vapor deposition on a double-polished c-Al2O3 substrate. The back of the c-Al2O3 substrate was deposited with aluminum as an external-feedback reflector. Significant enhancement of the EL intensity from ZnO, spectral narrowing, coupled with the superlinear increase in the ZnO EL intensity with the injection current have been observed, which are attributed to amplified spontaneous emission in the ZnO epilayer caused by the external optical feedback.


  • Observation of ultrahigh density InGaN quantum dots

    by H. L. Tsai, J. R. Yang, T. C. Wang, J. T. Hsu, M. Shiojiri

    High density InGaN quantum dots (QDs) grown on an underlying GaN layer that was partially masked with SiNx nanocrystals were investigated by cross-sectional high-angle annular dark-field (HAADF) scanning transmission electron microscopy (STEM), high-resolution transmission electron microscopy, and energy dispersive x-ray spectroscopy. The layer of SiNx masks appeared as a dark line in the HAADF-STEM images, and from the thickness of that dark line, the height of the masks was roughly estimated to be less than 2nm . The InGaN QDs appeared as bright triangles in the HAADF-STEM images. The QDs can be regarded as nanosized island crystals consisting of {101¯1} sidewalls, with a height of several nanometers. The lattices in the InGaN crystals were strained as compared to the underlying and the capping GaN lattices and contacted them coherently.


  • Structural analysis of strained p-type AlGaN∕GaN superlattice

    by H. L. Tsai, T. Y. Wang, J. R. Yang, C. C. Chuo, J. T. Hsu, M. Čeh, M. Shiojiri

    We investigated the nanostructure of AlGaN∕GaN strained-layer superlattice (SLS) cladding in the GaN-based violet laser diode (LD) and the AlInGaN-based ultraviolet (UV) light emitting diode (LED) with a scanning transmission electron microscope (STEM). In the p -SLS cladding, comprising 34 pairs of p‐Al0.1Ga0.9N∕p‐GaN:Mg layers in the GaN-based LD, the Al0.1Ga0.9N and GaN layers were distinguished as dark and bright bands ∼6nm wide in the high-angle annular dark-field (HAADF) STEM images. Threading dislocations (TDs) were observed. Among TDs that came from the underlying layer, some run outside through the SLS, and the others disappeared within the SLS, which discloses a role of the SLS in suppressing defect propagation. A HAADF-STEM image of the TD with a dark line along the center of a bright contour was found. The dark line, which was darker than the surrounding matrix, is striking. One of the probable explanations for the dark line that may be considered is local segregation of light atoms (Mg or Al) in Cottrell atmosphere around the dislocation core. In the HAADF-STEM image of the UV LED wafer, the AlInGaN and AlInGaN:Si layers in the MQW were definitely resolved, appearing as dark and bright bands. HAADF-STEM also distinguished between the AlGaN and GaN layers in the p -SLS cladding in the UV LED wafer.