Jilu Feng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jilu Feng has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Benoit Rivard
Department of Earth and Atmospheric Sciences, University of Alberta, Edmonton, AB T6G 2E3, Canada
5 shared publications - Derek A. Russell
Department of Chemical Engineering, Queen's University, Kingston, K7L 3N6, Canada
2 shared publications - Michael G. Lipsett
University of Alberta
2 shared publications - Vivek Bhushan
Enbridge Inc., Calgary, AB T2P 3L8, Canada
2 shared publications - Arturo Sanchez-Azofeifa
Earth and Atmospheric Sciences Department, Centre for Earth Observation Sciences, University of Alberta, Edmonton, Canada
1 shared publication - Danni Xie
Shaanxi Key Laboratory of Land Consolidation, School of Land Engineering, Chang’an University, Xi’an 710054, China
1 shared publication
Latest Publications
- Open Access
- 18 May 2022
- Published by MDPI AG in Remote Sensing
- Vol. 14 (10) , 2420
Estimation of Pb Content Using Reflectance Spectroscopy in Farmland Soil near Metal Mines, Central China
The contamination of farmlands with hazardous metals from mining puts the safety of agricultural commodities at risk. For remediation, it is crucial to map the spatial distribution of contaminated soil. Typical sampling-based procedures are time-consuming and labor-intensive. The use of visible, near-infrared, and short-wave infrared reflectance (VNIR-SWIR) spectroscopy to detect soil heavy metal pollution is an alternative. With the aim of investigating a methodology of detecting the most sensitive bands using VNIR-SWIR spectra to find lead (Pb) anomalies in agriculture soil near mining activities, the area in Xiaoqinling Mountain, downstream from a series of active gold mines, was selected to test the feasibility of utilizing VNIR-SWIR spectroscopy to map soil Pb. A total of 115 soil samples were collected for laboratory Pb analysis and spectral measurement. Partial least squares regression (PLSR) was adopted to estimate the soil Pb content by building the prediction model, and the model was optimized by finding the optimal number of bands involved. The spatial distribution of Pb concentration was mapped using the ordinary kriging (OK) interpolation method. This study found that five spectral bands (522 nm, 1668 nm, 2207 nm, 2296 nm, and 2345 nm) were sensitive to soil Pb content. The optimized prediction model’s coefficient of determination (R2), residual prediction deviation (RPD), and root mean square error (RMSE) were 0.711, 1.860, and 0.711 ln(mg/kg), respectively. Additionally, the result of OK interpolation was convincing and accurate (R2 = 0.775, RMSE = 0.328 ln(mg/kg)), comparing maps from estimated and ground truth data. This study proves that it is feasible to use VNIR-SWIR spectral data for in situ estimation of the soil Pb content.
- 18 May 2022
- Published by MDPI AG in Remote Sensing
- Vol. 14 (10) , 2420
Open AccessEstimation of Pb Content Using Reflectance Spectroscopy in Farmland Soil near Metal Mines, Central China
The contamination of farmlands with hazardous metals from mining puts the safety of agricultural commodities at risk. For remediation, it is crucial to map the spatial distribution of contaminated soil. Typical sampling-based procedures are time-consuming and labor-intensive. The use of visible, near-infrared, and short-wave infrared reflectance (VNIR-SWIR) spectroscopy to detect soil heavy metal pollution is an alternative. With the aim of investigating a methodology of detecting the most sensitive bands using VNIR-SWIR spectra to find lead (Pb) anomalies in agriculture soil near mining activities, the area in Xiaoqinling Mountain, downstream from a series of active gold mines, was selected to test the feasibility of utilizing VNIR-SWIR spectroscopy to map soil Pb. A total of 115 soil samples were collected for laboratory Pb analysis and spectral measurement. Partial least squares regression (PLSR) was adopted to estimate the soil Pb content by building the prediction model, and the model was optimized by finding the optimal number of bands involved. The spatial distribution of Pb concentration was mapped using the ordinary kriging (OK) interpolation method. This study found that five spectral bands (522 nm, 1668 nm, 2207 nm, 2296 nm, and 2345 nm) were sensitive to soil Pb content. The optimized prediction model’s coefficient of determination (R2), residual prediction deviation (RPD), and root mean square error (RMSE) were 0.711, 1.860, and 0.711 ln(mg/kg), respectively. Additionally, the result of OK interpolation was convincing and accurate (R2 = 0.775, RMSE = 0.328 ln(mg/kg)), comparing maps from estimated and ground truth data. This study proves that it is feasible to use VNIR-SWIR spectral data for in situ estimation of the soil Pb content.
- Open Access
Hyperspectral Characteristics of Oil Sand, Part 1: Prediction of Processability and Froth Quality from Measurements of Ore
This study is the first of two companion papers using hyperspectral data to generate predictive models of oil sand ore and froth characteristics as a potential new means for process control. In Alberta, Canada, shallow oil sands deposits are accessed by surface mining and crushed ore is transported to a processing plant for extraction of bitumen using flotation processes. The ore displays considerable variability in clay, bitumen, and fines which affects their behavior in flotation units. Using oil sand ore spanning a range of bitumen and fines characteristics, flotation experiments were performed to generate froth in a batch extractor to determine ore processability (e.g., separation performance) and froth characteristics (color, bitumen, solids). From hyperspectral observations of ore, models can predict the %bitumen content and %fines (particle passing at 44 and 3.9 µm) of ore but the models with highest r2 (>0.96) predict the solids/bitumen of froth and the processability of ore. Spectral observations collected on ore upstream of the separation vessels could therefore offer a first order assessment of froth quality for an ore blend before the ore enters the plant. These models could also potentially be used to monitor and control the performance of the blending process as another means to control the performance of the flotation process.
Open AccessHyperspectral Characteristics of Oil Sand, Part 1: Prediction of Processability and Froth Quality from Measurements of Ore
This study is the first of two companion papers using hyperspectral data to generate predictive models of oil sand ore and froth characteristics as a potential new means for process control. In Alberta, Canada, shallow oil sands deposits are accessed by surface mining and crushed ore is transported to a processing plant for extraction of bitumen using flotation processes. The ore displays considerable variability in clay, bitumen, and fines which affects their behavior in flotation units. Using oil sand ore spanning a range of bitumen and fines characteristics, flotation experiments were performed to generate froth in a batch extractor to determine ore processability (e.g., separation performance) and froth characteristics (color, bitumen, solids). From hyperspectral observations of ore, models can predict the %bitumen content and %fines (particle passing at 44 and 3.9 µm) of ore but the models with highest r2 (>0.96) predict the solids/bitumen of froth and the processability of ore. Spectral observations collected on ore upstream of the separation vessels could therefore offer a first order assessment of froth quality for an ore blend before the ore enters the plant. These models could also potentially be used to monitor and control the performance of the blending process as another means to control the performance of the flotation process.
- Open Access
Hyperspectral Characteristics of Oil Sand, Part 2: Prediction of Froth Characteristics from Measurements of Froth
This is the second part of a study of predictive models of oil sand ore and froth characteristics using infrared hyperspectral data as a potential new means for process control. In Alberta, Canada, bitumen in shallow oil sands deposits is accessed by surface mining and then extracted from ore using flotation processes. The ore displays variability in the clay, bitumen, and fines content and this variability affects the separability and product quality in flotation units. Flotation experiments were performed on a set of ore samples of different types to generate froth and determine the ore processability (e.g., separation performance) and froth characteristics (bitumen and solids content, fines distribution). We show that point spectra and spectral imagery of good quality can be acquired rapidly (2 = 0.88) and the %fines and ultrafines (particle passing at 3.9 and 0.5 µm) content of froth (r2 = 0.8 and 0.9, respectively). The latter model could be used to reject froth with a high solids content. Alternately, the strength of the illite-smectite absorption observed in froth could be used to retain all the samples above a pre-defined processability. Given that point spectrometers can currently be acquired for less than half the cost of an imaging system, we recommend the use of the former for future trials in operating environments.
Open AccessHyperspectral Characteristics of Oil Sand, Part 2: Prediction of Froth Characteristics from Measurements of Froth
This is the second part of a study of predictive models of oil sand ore and froth characteristics using infrared hyperspectral data as a potential new means for process control. In Alberta, Canada, bitumen in shallow oil sands deposits is accessed by surface mining and then extracted from ore using flotation processes. The ore displays variability in the clay, bitumen, and fines content and this variability affects the separability and product quality in flotation units. Flotation experiments were performed on a set of ore samples of different types to generate froth and determine the ore processability (e.g., separation performance) and froth characteristics (bitumen and solids content, fines distribution). We show that point spectra and spectral imagery of good quality can be acquired rapidly (2 = 0.88) and the %fines and ultrafines (particle passing at 3.9 and 0.5 µm) content of froth (r2 = 0.8 and 0.9, respectively). The latter model could be used to reject froth with a high solids content. Alternately, the strength of the illite-smectite absorption observed in froth could be used to retain all the samples above a pre-defined processability. Given that point spectrometers can currently be acquired for less than half the cost of an imaging system, we recommend the use of the former for future trials in operating environments.
- 1 October 2018
- Published by American Association of Petroleum Geologists AAPG/Datapages in AAPG Bulletin
- Vol. 102 (10) , 2101-2121
Inferring total organic carbon and major element geochemical and mineralogical characteristics of shale core from hyperspectral imagery
Hyperspectral systems that image drill core can capture detail mineralogical information at the millimeter scale and thus have the potential to enable investigators to characterize shale composition and heterogeneity, complementing the direct chemical and x-ray diffraction analysis of core samples and guiding detailed sampling. This method provides insight into petrophysical and geomechanical properties because these properties are significantly correlated to rock composition. We tested this approach on a continuous long core from the shale sequence of the Horn River Group in the Horn River Basin, British Columbia, sampled at a spacing of 1 m (40 in.) and analyzed for geochemical composition. These data enable the calibration of spectral imagery to rock composition and specifically predict total organic carbon (TOC) and the abundance of SiO2, Al2O3, K2O, and CaO. We then imaged nine samples from the Woodford Shale from the Permian Basin, Texas, for a blind test to assess the predictive models. The models were then used to predict TOC and geochemical data over detailed imagery of 300 m (984 ft) of Horn River Group shale core and portray their spatial variability downhole as images and profiles. In its simplest form, hyperspectral imagery can be enhanced to highlight fabric in shale core that otherwise is difficult to visualize because of low brightness. In addition, we show that spectral imagery of shale can also be processed to either convey mineralogical (quartz, clay, and carbonate) or geochemical information. The resulting views can readily be used to guide the selection of samples and may provide tools for scaling reservoir properties from individual plugs to reservoir volumes.
- 1 October 2018
- Published by American Association of Petroleum Geologists AAPG/Datapages in AAPG Bulletin
- Vol. 102 (10) , 2101-2121
Inferring total organic carbon and major element geochemical and mineralogical characteristics of shale core from hyperspectral imagery
Hyperspectral systems that image drill core can capture detail mineralogical information at the millimeter scale and thus have the potential to enable investigators to characterize shale composition and heterogeneity, complementing the direct chemical and x-ray diffraction analysis of core samples and guiding detailed sampling. This method provides insight into petrophysical and geomechanical properties because these properties are significantly correlated to rock composition. We tested this approach on a continuous long core from the shale sequence of the Horn River Group in the Horn River Basin, British Columbia, sampled at a spacing of 1 m (40 in.) and analyzed for geochemical composition. These data enable the calibration of spectral imagery to rock composition and specifically predict total organic carbon (TOC) and the abundance of SiO2, Al2O3, K2O, and CaO. We then imaged nine samples from the Woodford Shale from the Permian Basin, Texas, for a blind test to assess the predictive models. The models were then used to predict TOC and geochemical data over detailed imagery of 300 m (984 ft) of Horn River Group shale core and portray their spatial variability downhole as images and profiles. In its simplest form, hyperspectral imagery can be enhanced to highlight fabric in shale core that otherwise is difficult to visualize because of low brightness. In addition, we show that spectral imagery of shale can also be processed to either convey mineralogical (quartz, clay, and carbonate) or geochemical information. The resulting views can readily be used to guide the selection of samples and may provide tools for scaling reservoir properties from individual plugs to reservoir volumes.
- 1 September 2018
- Published by American Association of Petroleum Geologists AAPG/Datapages in AAPG Bulletin
- Vol. 102 (9) , 1671-1683
Shortwave infrared (1.0–2.5 µm) hyperspectral imaging of the Athabasca West Grand Rapids Formation oil sands
Previous work on the reflectance spectroscopy of oil sands has focused exclusively on the McMurray Formation of the Athabasca deposit. However, as industrial development expands into other formations, spectral research on Alberta’s other bitumen reservoirs is warranted. This study presents the first investigation of shortwave infrared (SWIR; 1.0–2.5 μm) hyperspectral imaging of Grand Rapids Formation oil sands. Comparing the spectral properties of Grand Rapids oil sands to that of the McMurray Formation reveals some key differences. Grand Rapids oil sands have lower overall reflectance and deeper 1.4- and 1.9-μm absorption features than McMurray oil sands of the same ore grade. At ore grades greater than 10 wt. %, Grand Rapids oil sands also have shallower bitumen absorption features. These spectral differences may be attributed to the mineralogical differences between the two formations, namely, structural water in K-feldspar. Hyperspectral analysis techniques that have been previously developed for McMurray oil sands were tested on a Grand Rapids Formation core. Using contrast stretching and the three-band combination of R = 2.05 µm, G = 2.13 µm, and B = 2.28 µm (where R, G, and B refer to red, green, and blue channels), the visibility of sedimentological features was enhanced in SWIR imagery. With a simple recalibration, an established spectral model for the estimation of total bitumen content (TBC) produced results in close agreement with Dean–Stark analysis data (coefficient of determination [R2] = 0.92, ±1.1 wt. %) and of similar accuracy to what has been previously demonstrated for the McMurray Formation. The results of this study suggest that with minor adjustments, oil sands spectral analysis techniques are transferable between different geological formations.
- 1 September 2018
- Published by American Association of Petroleum Geologists AAPG/Datapages in AAPG Bulletin
- Vol. 102 (9) , 1671-1683
Shortwave infrared (1.0–2.5 µm) hyperspectral imaging of the Athabasca West Grand Rapids Formation oil sands
Previous work on the reflectance spectroscopy of oil sands has focused exclusively on the McMurray Formation of the Athabasca deposit. However, as industrial development expands into other formations, spectral research on Alberta’s other bitumen reservoirs is warranted. This study presents the first investigation of shortwave infrared (SWIR; 1.0–2.5 μm) hyperspectral imaging of Grand Rapids Formation oil sands. Comparing the spectral properties of Grand Rapids oil sands to that of the McMurray Formation reveals some key differences. Grand Rapids oil sands have lower overall reflectance and deeper 1.4- and 1.9-μm absorption features than McMurray oil sands of the same ore grade. At ore grades greater than 10 wt. %, Grand Rapids oil sands also have shallower bitumen absorption features. These spectral differences may be attributed to the mineralogical differences between the two formations, namely, structural water in K-feldspar. Hyperspectral analysis techniques that have been previously developed for McMurray oil sands were tested on a Grand Rapids Formation core. Using contrast stretching and the three-band combination of R = 2.05 µm, G = 2.13 µm, and B = 2.28 µm (where R, G, and B refer to red, green, and blue channels), the visibility of sedimentological features was enhanced in SWIR imagery. With a simple recalibration, an established spectral model for the estimation of total bitumen content (TBC) produced results in close agreement with Dean–Stark analysis data (coefficient of determination [R2] = 0.92, ±1.1 wt. %) and of similar accuracy to what has been previously demonstrated for the McMurray Formation. The results of this study suggest that with minor adjustments, oil sands spectral analysis techniques are transferable between different geological formations.
- Open Access
Estimation of the Distribution of Tabebuia guayacan (Bignoniaceae) Using High-Resolution Remote Sensing Imagery
Species identification and characterization in tropical environments is an emerging field in tropical remote sensing. Significant efforts are currently aimed at the detection of tree species, of levels of forest successional stages, and the extent of liana occurrence at the top of canopies. In this paper we describe our use of high resolution imagery from the Quickbird Satellite to estimate the flowering population of Tabebuia guayacan trees at Barro Colorado Island (BCI), in Panama. The imagery was acquired on 29 April 2002 and 21 March 2004. Spectral Angle Mapping via a One-Class Support Vector machine was used to detect the presence of 422 and 557 flowering tress in the April 2002 and March 2004 imagery. Of these, 273 flowering trees are common to both dates. This study presents a new perspective on the effectiveness of high resolution remote sensing for monitoring a phenological response and its use as a tool for potential conservation and management of natural resources in tropical environments.
Open AccessEstimation of the Distribution of Tabebuia guayacan (Bignoniaceae) Using High-Resolution Remote Sensing Imagery
Species identification and characterization in tropical environments is an emerging field in tropical remote sensing. Significant efforts are currently aimed at the detection of tree species, of levels of forest successional stages, and the extent of liana occurrence at the top of canopies. In this paper we describe our use of high resolution imagery from the Quickbird Satellite to estimate the flowering population of Tabebuia guayacan trees at Barro Colorado Island (BCI), in Panama. The imagery was acquired on 29 April 2002 and 21 March 2004. Spectral Angle Mapping via a One-Class Support Vector machine was used to detect the presence of 422 and 557 flowering tress in the April 2002 and March 2004 imagery. Of these, 273 flowering trees are common to both dates. This study presents a new perspective on the effectiveness of high resolution remote sensing for monitoring a phenological response and its use as a tool for potential conservation and management of natural resources in tropical environments.