Yiping Huang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Yiping Huang has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- David Wei Zhang
State Key Lab of ASIC & Systems, Fudan University, Shanghai 201203, China
1 shared publication - Guoan Liu
Semiconductor Manufacturing Electronics (Shaoxing) Corporation, Shaoxing 312035, China
1 shared publication - Jia Zhou
State Key Laboratory of ASIC and System, School of Microelectronics, Fudan University, Shanghai, China
1 shared publication - MinHang Bao
ASIC and System National Key Lab, Department of Microelectronics, Fudan University, Shanghai 200433, China
1 shared publication - Qingqing Sun
Fudan University
1 shared publication - Xuanjie Liu
School of Microelectronics, Fudan University, Shanghai 200433, China
1 shared publication
Latest Publications
- Open Access
- 29 September 2021
- Published by MDPI AG in Electronics
- Vol. 10 (19) , 2370
Optimization of TSV Leakage in Via-Middle TSV Process for Wafer-Level Packaging
Through silicon via (TSV) offers a promising solution for the vertical connection of chip I/O, which enables smaller and thinner package sizes and cost-effective products by using wafer-level packaging instead of a chip-level process. However, TSV leakage has become a critical concern in the BEOL process. In this paper, a Cu-fulfilled via-middle TSV with 100 µm depth embedded in 0.18 µm CMOS process for sensor application is presented, focusing on the analysis and optimization of TSV leakage. By using etch process, substrate defect, and thermal processing co-optimization, TSV leakage failure can be successfully avoided, which can be very instructive for the improvement in TSV wafer-level package yield as well as device performance in advanced semiconductor technology.
- 29 September 2021
- Published by MDPI AG in Electronics
- Vol. 10 (19) , 2370
Open AccessOptimization of TSV Leakage in Via-Middle TSV Process for Wafer-Level Packaging
Through silicon via (TSV) offers a promising solution for the vertical connection of chip I/O, which enables smaller and thinner package sizes and cost-effective products by using wafer-level packaging instead of a chip-level process. However, TSV leakage has become a critical concern in the BEOL process. In this paper, a Cu-fulfilled via-middle TSV with 100 µm depth embedded in 0.18 µm CMOS process for sensor application is presented, focusing on the analysis and optimization of TSV leakage. By using etch process, substrate defect, and thermal processing co-optimization, TSV leakage failure can be successfully avoided, which can be very instructive for the improvement in TSV wafer-level package yield as well as device performance in advanced semiconductor technology.
- Open Access
Modeling of Photoinduced Deformation in Silicon Microcantilever
A model for prediction the photostriction effect in silicon microcantilevers is built up based on the fundamentals of mechanics and semiconductor physics. By considering the spatial distribution and surface recombination of photoinduced carriers in silicon, the model interprets the cause of the photoinduced bending. The results from our model much more closely approximate the experimental values than the former model built up by Datskos, Rajic and Datskou [1](APL, Vol.73 (1998) No.16, pp 3219-2321), represented by the reduction of the error between calculation and measurement from 25 times to 0.85 times.
Open AccessModeling of Photoinduced Deformation in Silicon Microcantilever
A model for prediction the photostriction effect in silicon microcantilevers is built up based on the fundamentals of mechanics and semiconductor physics. By considering the spatial distribution and surface recombination of photoinduced carriers in silicon, the model interprets the cause of the photoinduced bending. The results from our model much more closely approximate the experimental values than the former model built up by Datskos, Rajic and Datskou [1](APL, Vol.73 (1998) No.16, pp 3219-2321), represented by the reduction of the error between calculation and measurement from 25 times to 0.85 times.