Dirk W. Schubert
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Dirk W. Schubert has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
Bastian L Walter
Friedrich‐Alexander University Erlangen‐Nuremberg Institute of Polymer Materials Martensstraße 7 91058 Erlangen Germany
1 shared publicationJoachim Kaschta
Friedrich‐Alexander University Erlangen‐Nuremberg Institute of Polymer Materials Martensstraße 7 91058 Erlangen Germany
1 shared publicationJohannes Krückel
Institute of Polymer Materials, Friedrich-Alexander-University Erlangen-Nuremberg, Martensstr. 7, 91058 Erlangen, Germany
1 shared publicationJonas Daenicke
Friedrich‐Alexander University Erlangen‐Nuremberg Institute of Polymer Materials Martensstraße 7 91058 Erlangen Germany
1 shared publicationMichael Härth
Institute of Polymer Materials, Department of Materials Science, Friedrich-Alexander University Erlangen-Nuremberg, Martensstrasse 7, 91058 Erlangen, Germany
1 shared publication- Raymund E. Horch
Universitätsklinikum Erlangen, Friedrich-Alexander-Universität Erlangen-Nürnberg FAU, Bavaria, Germany
1 shared publication
Latest Publications
- 11 September 2013
- Published by Wiley in Polymer International
- Vol. 63 (2) , 172-178
On the failure of silicone breast implants: new insights by mapping the mechanical properties of implant shells
This review summarizes the knowledge on rupture (in vivo as well as under laboratory conditions) of gel‐filled silicone breast implants, which has been an open question since the first implantation in 1962. We present recent progress which has been made by a mapping of the mechanical properties of the shell material together with a statistical failure analysis by means of a Weibull fit. Reference implants and intact as well as ruptured explants are tested after several years in vivo using tensile tests. Up to 110 dumbbell‐shaped specimens per implant are measured allowing a detailed mapping of the mechanical properties of the silicone shell. Therefore, it is possible to illustrate the results of the tensile tests by mapping the measured values of the implants in the form of a contour plot revealing novel insights. The contour plots clearly display that the mechanical behaviour (e.g. stress at break) varies significantly over the shell. Additionally, a map is proposed which clearly shows separated clusters for different manufacturers and product categories. © 2013 Society of Chemical Industry
- 11 September 2013
- Published by Wiley in Polymer International
- Vol. 63 (2) , 172-178
On the failure of silicone breast implants: new insights by mapping the mechanical properties of implant shells
This review summarizes the knowledge on rupture (in vivo as well as under laboratory conditions) of gel‐filled silicone breast implants, which has been an open question since the first implantation in 1962. We present recent progress which has been made by a mapping of the mechanical properties of the shell material together with a statistical failure analysis by means of a Weibull fit. Reference implants and intact as well as ruptured explants are tested after several years in vivo using tensile tests. Up to 110 dumbbell‐shaped specimens per implant are measured allowing a detailed mapping of the mechanical properties of the silicone shell. Therefore, it is possible to illustrate the results of the tensile tests by mapping the measured values of the implants in the form of a contour plot revealing novel insights. The contour plots clearly display that the mechanical behaviour (e.g. stress at break) varies significantly over the shell. Additionally, a map is proposed which clearly shows separated clusters for different manufacturers and product categories. © 2013 Society of Chemical Industry
- 1 January 2013
- Published by AIP Publishing in AIP Conference Proceedings
Shear induced electrical behaviour of conductive polymer composites
The time-dependent electrical resistance of polymethylmethacrylate containing carbon black was measured under oscillatory shear in the molten state. The electrical signal was oscillating exactly at the doubled frequency of the oscillatory shear deformation. Moreover, the experimental results gave a hint to the development of conductive structures in polymer melts under shear deformation. It was shown that the flow induced destruction of conductive paths dominates over the flow induced build-up in the beginning of the shear deformations. However, for longer times both competitive effects reach a dynamic equilibrium and only the thermally induced build-up of pathways influences the changes in the composite resistance during the shear. Furthermore, the oscillating electrical response depends clearly on the deformation amplitude applied. A simple physical model describing the behaviour of conductive pathways under shear deformation was derived and utilized for the description of the experimental data.
- 1 January 2013
- Published by AIP Publishing in AIP Conference Proceedings
Shear induced electrical behaviour of conductive polymer composites
The time-dependent electrical resistance of polymethylmethacrylate containing carbon black was measured under oscillatory shear in the molten state. The electrical signal was oscillating exactly at the doubled frequency of the oscillatory shear deformation. Moreover, the experimental results gave a hint to the development of conductive structures in polymer melts under shear deformation. It was shown that the flow induced destruction of conductive paths dominates over the flow induced build-up in the beginning of the shear deformations. However, for longer times both competitive effects reach a dynamic equilibrium and only the thermally induced build-up of pathways influences the changes in the composite resistance during the shear. Furthermore, the oscillating electrical response depends clearly on the deformation amplitude applied. A simple physical model describing the behaviour of conductive pathways under shear deformation was derived and utilized for the description of the experimental data.
- 5 March 2012
- Published by Wiley in Macromolecular Chemistry and Physics
- Vol. 213 (6) , 654-665
Simple Approach for Spreading Dynamics of Polymeric Fluids
The spreading of an axisymmetric drop on partially and completely wetted substrates is investigated from the theoretical and experimental point of view. In particular, novel physical models considering the capillary force, the gravitational force, and a viscous friction force simultaneously are derived. The models enable the analytical mathematical description of the drop radius as a function of the spreading time, which is useful for practical applications. Moreover, the construction of a master curve for the partial wetting scenario is proposed. The theoretical models are experimentally verified, using different polymer films as substrates and polydimethylsiloxanes of different viscosities as liquids. The comparison shows that theory and experiment are consistent.
- 5 March 2012
- Published by Wiley in Macromolecular Chemistry and Physics
- Vol. 213 (6) , 654-665
Simple Approach for Spreading Dynamics of Polymeric Fluids
The spreading of an axisymmetric drop on partially and completely wetted substrates is investigated from the theoretical and experimental point of view. In particular, novel physical models considering the capillary force, the gravitational force, and a viscous friction force simultaneously are derived. The models enable the analytical mathematical description of the drop radius as a function of the spreading time, which is useful for practical applications. Moreover, the construction of a master curve for the partial wetting scenario is proposed. The theoretical models are experimentally verified, using different polymer films as substrates and polydimethylsiloxanes of different viscosities as liquids. The comparison shows that theory and experiment are consistent.