Claudia E. Zapata
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Claudia E. Zapata has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Sandra L. Houston
Arizona State Univ
5 shared publications - William N. Houston
Arizona State Univ
3 shared publications - Carlos E. Cary
Civil Engineer, Gemini Technologies, 3153 Fire Rd., Suite 2A, Egg Harbor Township, NJ 08234
2 shared publications H. B. Dye
Graduate Research Assistant, Arizona State University, Dept of Civil and Environmental Engineering, P.O. Box 875306, Tempe, AZ 85287-5306
2 shared publications- Kenneth D. Walsh
Dean, San Diego State Univ.–Georgia, 5 MerabKostava St., 3rd Floor, Tbilisi 0108, Georgia; Professor and Chair, AGC-Paul S. Roel Chair in Construction Engineering and Management, Dept. of Civil, Construction, and Environmental Engineering, San Diego State Univ., 5500 Campanile Dr., San Diego, CA 92182-1324
2 shared publications - Pugazhvel Thirthar Palanivelu2 shared publications
Latest Publications
- Open Access
- 23 December 2025
- Published by MDPI AG in Geosciences
- Vol. 16 (1) , 12
A Non-Linear Suction-Dependent Model for Predicting Unsaturated Shear Strength
Accurate evaluation of unsaturated shear strength remains a significant challenge in geotechnical engineering because of the nonlinear interaction between matric suction and shear strength. Existing models often assume a linear contribution of suction and are generally restricted to low suction ranges, limiting their predictive capability under highly unsaturated conditions. This study investigated the nonlinear response of unsaturated shear strength through single-stage direct shear tests conducted under constant water content. Two soil types: a high-plasticity clay and a low-plasticity silty clay were examined across a wide suction range extending beyond the air-entry value (AEV). The results revealed a nonlinear behavior expressed as a distinct bi-linear trend, with shear strength increasing with suction up to the optimal moisture condition and then exhibiting a clearly altered rate of increase at higher suction levels. To capture this nonlinear behavior of unsaturated shear strength with suction, an exponential shear strength equation was proposed and validated using eight additional published datasets encompassing different soil classifications and suction magnitudes. The proposed formulation demonstrates that accounting for non-linearity is essential for accurately estimating the unsaturated shear strength of the soil. Moreover, the proposed exponential model outperforms both the well-established linear model of Fredlund and the nonlinear power law model of Abramento and Carvalho, thereby providing a unified framework for capturing the nonlinear interaction of matric suction on unsaturated shear strength.
- 23 December 2025
- Published by MDPI AG in Geosciences
- Vol. 16 (1) , 12
Open AccessA Non-Linear Suction-Dependent Model for Predicting Unsaturated Shear Strength
Accurate evaluation of unsaturated shear strength remains a significant challenge in geotechnical engineering because of the nonlinear interaction between matric suction and shear strength. Existing models often assume a linear contribution of suction and are generally restricted to low suction ranges, limiting their predictive capability under highly unsaturated conditions. This study investigated the nonlinear response of unsaturated shear strength through single-stage direct shear tests conducted under constant water content. Two soil types: a high-plasticity clay and a low-plasticity silty clay were examined across a wide suction range extending beyond the air-entry value (AEV). The results revealed a nonlinear behavior expressed as a distinct bi-linear trend, with shear strength increasing with suction up to the optimal moisture condition and then exhibiting a clearly altered rate of increase at higher suction levels. To capture this nonlinear behavior of unsaturated shear strength with suction, an exponential shear strength equation was proposed and validated using eight additional published datasets encompassing different soil classifications and suction magnitudes. The proposed formulation demonstrates that accounting for non-linearity is essential for accurately estimating the unsaturated shear strength of the soil. Moreover, the proposed exponential model outperforms both the well-established linear model of Fredlund and the nonlinear power law model of Abramento and Carvalho, thereby providing a unified framework for capturing the nonlinear interaction of matric suction on unsaturated shear strength.
- 22 October 2024
- Published by Springer Nature
- p. 249-257
Short-Term Thornthwaite Moisture Index (TMI) for Australian Climate
- 22 October 2024
- Published by Springer Nature
- p. 249-257
Short-Term Thornthwaite Moisture Index (TMI) for Australian Climate
- Open Access
- 28 January 2024
- Published by MDPI AG in Geosciences
- Vol. 14 (2) , 34
A Multiphysics Simulation of the Effects of Wicking Geotextile on Mitigating Frost Heave under Cold Region Pavement
Geotextile offers numerous benefits in improving pavement performance, including drainage, barrier functionality, filtration, and reinforcement. Wicking geotextile, a novel variant in this category, possesses the intrinsic ability to drain water autonomously from soils. This paper details the development and application of a comprehensive multiphysics model that simulates the performance of wicking geotextile within a pavement system under freezing climates. The model considers the inputs of various environmental dynamics, including the impact of meteorological factors, groundwater levels, ground heat, and drainage on the pavement system. The model was firstly validated using field data from a long-term pavement performance (LTPP) road section in the cold region. It was subsequently applied to assess the impacts of wicking geotextile if it was installed on the road section. The model simulated the coupled temporal and spatial variations in soil moisture content and temperature. The simulation results demonstrated that wicking geotextile would create a suction zone around its installation location to draw water from surrounding soils, therefore reducing the overall unfrozen water content in the pavement. The results also showed that the installation of wicking geotextile would delay the initiation of frost heave and reduce its magnitude in cold region pavement.
- 28 January 2024
- Published by MDPI AG in Geosciences
- Vol. 14 (2) , 34
Open AccessA Multiphysics Simulation of the Effects of Wicking Geotextile on Mitigating Frost Heave under Cold Region Pavement
Geotextile offers numerous benefits in improving pavement performance, including drainage, barrier functionality, filtration, and reinforcement. Wicking geotextile, a novel variant in this category, possesses the intrinsic ability to drain water autonomously from soils. This paper details the development and application of a comprehensive multiphysics model that simulates the performance of wicking geotextile within a pavement system under freezing climates. The model considers the inputs of various environmental dynamics, including the impact of meteorological factors, groundwater levels, ground heat, and drainage on the pavement system. The model was firstly validated using field data from a long-term pavement performance (LTPP) road section in the cold region. It was subsequently applied to assess the impacts of wicking geotextile if it was installed on the road section. The model simulated the coupled temporal and spatial variations in soil moisture content and temperature. The simulation results demonstrated that wicking geotextile would create a suction zone around its installation location to draw water from surrounding soils, therefore reducing the overall unfrozen water content in the pavement. The results also showed that the installation of wicking geotextile would delay the initiation of frost heave and reduce its magnitude in cold region pavement.
- 27 August 2021
- Published by ABMS - Brazilian Association for Soil Mechanics and Geotechnical Engineering in Soils and Rocks
- Vol. 44 (3) , 1-14
An improved framework for volume change of shrink/swell soils subjected to time-varying climatic effects
The ability to estimate soil volume change as a function of time is a valuable tool in the design or forensic analysis of shallow foundations and pavement structures. This paper presents an improved framework for estimating the volume change of shrink/swell soils due to time-varying climatic effects using the Lytton et al. (2005) approach with the suction envelope models created by Vann & Houston (2021) and updated considerations of short-term varying climate. The procedure can be easily implemented in any country due to its mechanistic-empirical nature. The authors present an example calculation of the proposed framework using the data from an American Association of State Highway and Transportation Officials (AASHTO) Long-Term Pavement Performance (LTPP) Seasonal Monitoring Program (SMP) section, located approximately 80 miles northeast of Dallas, Texas. The volume change estimated from the proposed framework was compared to 70 measured data points from sections from the SMP study and the results look promising. The models are universal and can be used in any part of the world provided measured data is available to calibrate for local conditions. Ongoing calibration effort with the remaining LTPP SMP sections will allow obtaining calibration factors for the proposed framework that will improve the estimation of the volume change predictions under pavements and facilitate the implementation into current design procedures.
- 27 August 2021
- Published by ABMS - Brazilian Association for Soil Mechanics and Geotechnical Engineering in Soils and Rocks
- Vol. 44 (3) , 1-14
An improved framework for volume change of shrink/swell soils subjected to time-varying climatic effects
The ability to estimate soil volume change as a function of time is a valuable tool in the design or forensic analysis of shallow foundations and pavement structures. This paper presents an improved framework for estimating the volume change of shrink/swell soils due to time-varying climatic effects using the Lytton et al. (2005) approach with the suction envelope models created by Vann & Houston (2021) and updated considerations of short-term varying climate. The procedure can be easily implemented in any country due to its mechanistic-empirical nature. The authors present an example calculation of the proposed framework using the data from an American Association of State Highway and Transportation Officials (AASHTO) Long-Term Pavement Performance (LTPP) Seasonal Monitoring Program (SMP) section, located approximately 80 miles northeast of Dallas, Texas. The volume change estimated from the proposed framework was compared to 70 measured data points from sections from the SMP study and the results look promising. The models are universal and can be used in any part of the world provided measured data is available to calibrate for local conditions. Ongoing calibration effort with the remaining LTPP SMP sections will allow obtaining calibration factors for the proposed framework that will improve the estimation of the volume change predictions under pavements and facilitate the implementation into current design procedures.
- 20 June 2018
- Published by American Society of Civil Engineers (ASCE)
- p. 149-173
Empirical Approach for the Use of Unsaturated Soil Mechanics in Pavement Design
Historically, most of the pavement design procedures used in worldwide practice are based upon a simplifying (but costly) assumption that all aggregates and subgrade materials would eventually become fully saturated in their performance life cycle. However, the majority of all pavement layers will not exist in a fully saturated state. Field evidence and numerous numerical modeling studies have shown that even though the pavement acts as a cover for the unbound material, its moisture content will change with time, in an attempt to reach an equilibrium condition. This fact it is greatly influenced by climate regime and soil properties. The development of the initial mechanistic empirical pavement design guide (MEPDG) by the American Association of State Highway and Transportation Officials (AASHTO) incorporated, for the first time, a design methodology for pavement systems that considered unsaturated material response and prediction techniques based upon the site specific environmental conditions. This paper presents an overview of the models used in the MEPDG for the prediction of unbound pavement layer material performance and discusses several revisions to various models that can greatly enhance the MEPDG design procedure.
- 20 June 2018
- Published by American Society of Civil Engineers (ASCE)
- p. 149-173
Empirical Approach for the Use of Unsaturated Soil Mechanics in Pavement Design
Historically, most of the pavement design procedures used in worldwide practice are based upon a simplifying (but costly) assumption that all aggregates and subgrade materials would eventually become fully saturated in their performance life cycle. However, the majority of all pavement layers will not exist in a fully saturated state. Field evidence and numerous numerical modeling studies have shown that even though the pavement acts as a cover for the unbound material, its moisture content will change with time, in an attempt to reach an equilibrium condition. This fact it is greatly influenced by climate regime and soil properties. The development of the initial mechanistic empirical pavement design guide (MEPDG) by the American Association of State Highway and Transportation Officials (AASHTO) incorporated, for the first time, a design methodology for pavement systems that considered unsaturated material response and prediction techniques based upon the site specific environmental conditions. This paper presents an overview of the models used in the MEPDG for the prediction of unbound pavement layer material performance and discusses several revisions to various models that can greatly enhance the MEPDG design procedure.
- 20 June 2018
- Published by American Society of Civil Engineers (ASCE)
- p. 523-532
Assessment of Cary and Zapata Suction Based Model for Prediction of Resilient Modulus in Fine Grained Subgrade Soils
Stiffness of pavement subgrade materials that is commonly determined by the resilient modulus parameter is an important component in the mechanistic design of flexible pavement structures. The universal model, which makes use of the bulk and octahedral stresses as predicting parameters, is used to predict the soil resilient modulus in the MEPDG design. Recent studies performed by Cary and Zapata (2011) lead to the development of a model that incorporates the soil matric suction as one of the fundamental stress state predictors. This model requires the measurement of change in suction during the loading process, which makes it difficult for implementation. In order to overcome the difficulties involved and aid in the implementation of the Cary and Zapata’s (2011) resilient modulus model, a laboratory study using two fine grained materials was accomplished to assess changes in suction parameter of different unsaturated soil materials during cyclic loading. Based on the results obtained, recommendations for implementation of the model are presented.
- 20 June 2018
- Published by American Society of Civil Engineers (ASCE)
- p. 523-532
Assessment of Cary and Zapata Suction Based Model for Prediction of Resilient Modulus in Fine Grained Subgrade Soils
Stiffness of pavement subgrade materials that is commonly determined by the resilient modulus parameter is an important component in the mechanistic design of flexible pavement structures. The universal model, which makes use of the bulk and octahedral stresses as predicting parameters, is used to predict the soil resilient modulus in the MEPDG design. Recent studies performed by Cary and Zapata (2011) lead to the development of a model that incorporates the soil matric suction as one of the fundamental stress state predictors. This model requires the measurement of change in suction during the loading process, which makes it difficult for implementation. In order to overcome the difficulties involved and aid in the implementation of the Cary and Zapata’s (2011) resilient modulus model, a laboratory study using two fine grained materials was accomplished to assess changes in suction parameter of different unsaturated soil materials during cyclic loading. Based on the results obtained, recommendations for implementation of the model are presented.
- 1 December 2017
- Published by Elsevier in Transportation Geotechnics
- Vol. 13, 13-27
Evaluation of the Federal Aviation Administration methodology for characterizing the nonlinear behavior of granular base and subbase materials
- 1 December 2017
- Published by Elsevier in Transportation Geotechnics
- Vol. 13, 13-27
Evaluation of the Federal Aviation Administration methodology for characterizing the nonlinear behavior of granular base and subbase materials
- 1 January 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 29 (1)
Effect of Wetting and Drying Cycles on the Behavior of Compacted Expansive Soils
In the United States alone, the cost to repair structures damaged by expansive soils has been estimated to be twice the combined damages of natural disasters. Despite the widespread occurrence of these soils, the damage caused by the presence of expansive soils is regularly overlooked because it might take years of distress exposure before extensive damage to infrastructure can be observed. To predict the heave and swelling pressure an expansive soil will experience in the field, it is standard practice to subject a remolded specimen to a wetting process at a particular net normal stress. This practice does not capture the behavior of expansive soils in the field and therefore, it is necessary to assess the long-term environmental effects on their behavior. In this study, an assessment of the effect of multiple wetting/drying cycles on the volume change behavior of two naturally occurring expansive soils was performed. The soils were remolded at different initial compacted conditions, loaded to different net normal stresses, wetted to nearly 100% saturation and then subjected to full drying. In general, it was observed that after four cycles, the swelling or collapse strain and the swell pressure reached equilibrium. When the applied stress exceeded 25% of the swell pressure, both soils exhibited an increase in collapse potential from the previous wetting cycle. However, when the applied stress was less than 25% of the swell pressure, both soils exhibited an increase in swell potential from the previous cycle.
- 1 January 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 29 (1)
Effect of Wetting and Drying Cycles on the Behavior of Compacted Expansive Soils
In the United States alone, the cost to repair structures damaged by expansive soils has been estimated to be twice the combined damages of natural disasters. Despite the widespread occurrence of these soils, the damage caused by the presence of expansive soils is regularly overlooked because it might take years of distress exposure before extensive damage to infrastructure can be observed. To predict the heave and swelling pressure an expansive soil will experience in the field, it is standard practice to subject a remolded specimen to a wetting process at a particular net normal stress. This practice does not capture the behavior of expansive soils in the field and therefore, it is necessary to assess the long-term environmental effects on their behavior. In this study, an assessment of the effect of multiple wetting/drying cycles on the volume change behavior of two naturally occurring expansive soils was performed. The soils were remolded at different initial compacted conditions, loaded to different net normal stresses, wetted to nearly 100% saturation and then subjected to full drying. In general, it was observed that after four cycles, the swelling or collapse strain and the swell pressure reached equilibrium. When the applied stress exceeded 25% of the swell pressure, both soils exhibited an increase in collapse potential from the previous wetting cycle. However, when the applied stress was less than 25% of the swell pressure, both soils exhibited an increase in swell potential from the previous cycle.
- 8 February 2016
- Published by American Society of Civil Engineers (ASCE)
- p. 1435-1449
Effect of Bagasse Fiber on the Properties of Compressed Cement Stabilized Earth Blocks
Concern and interest about the environment and ecologic systems have promoted the usage of earth as a construction material. Technology advancement has resulted in the evolution of old adobe and cob into compressed stabilized earth blocks (CSEBs). Compressed stabilized earth blocks are prepared by compressing the soil-stabilizer mixture at a particular stress. In order to accomplish the required strength, cement has been used in a regular basis as stabilizing agent, at proportions that are still harmful to the environment. CSEB blocks have various advantages related to cost reduction, energy efficiency and environmental friendly and therefore, it is of interest to find means to reduce the amount of cement used in their construction without affecting its dry strength and durability. In this study, natural fibers were used along with lower proportions of cement than those commonly used in practice and varying fine content in the soil to assess its effect on the dry strength and durability of the blocks. Blocks were compacted with 10MPa stress and prepared by using 7%, 5% and 3% cement along with varying fiber content ranging from 0.25% to 2%. The effect of fine content, cement and fibers on strength and durability of the natural fiber-reinforced blocks was studied. Sand/clay fractions of a native soil from the Phoenix area were used to fabricate the blocks. Preliminary results indicate that the compressive strength reaches a maximum value for blocks with 30% fine content; blocks with 5% cement withstand the durability test; an increase in fiber content decreases the strength of the material; and finally, the soil-cement loss was minimal for blocks with 50% fine content.
- 8 February 2016
- Published by American Society of Civil Engineers (ASCE)
- p. 1435-1449
Effect of Bagasse Fiber on the Properties of Compressed Cement Stabilized Earth Blocks
Concern and interest about the environment and ecologic systems have promoted the usage of earth as a construction material. Technology advancement has resulted in the evolution of old adobe and cob into compressed stabilized earth blocks (CSEBs). Compressed stabilized earth blocks are prepared by compressing the soil-stabilizer mixture at a particular stress. In order to accomplish the required strength, cement has been used in a regular basis as stabilizing agent, at proportions that are still harmful to the environment. CSEB blocks have various advantages related to cost reduction, energy efficiency and environmental friendly and therefore, it is of interest to find means to reduce the amount of cement used in their construction without affecting its dry strength and durability. In this study, natural fibers were used along with lower proportions of cement than those commonly used in practice and varying fine content in the soil to assess its effect on the dry strength and durability of the blocks. Blocks were compacted with 10MPa stress and prepared by using 7%, 5% and 3% cement along with varying fiber content ranging from 0.25% to 2%. The effect of fine content, cement and fibers on strength and durability of the natural fiber-reinforced blocks was studied. Sand/clay fractions of a native soil from the Phoenix area were used to fabricate the blocks. Preliminary results indicate that the compressive strength reaches a maximum value for blocks with 30% fine content; blocks with 5% cement withstand the durability test; an increase in fiber content decreases the strength of the material; and finally, the soil-cement loss was minimal for blocks with 50% fine content.
- 8 February 2016
- Published by American Society of Civil Engineers (ASCE)
- p. 1303-1316
Effect of As-Compacted Moisture Content and Density on Pavement Performance in Different Climatic Regimes
While asphalt-concrete layer properties are more sensitive towards temperature variations, the subgrade stiffness have proven to be quite sensitive to moisture content fluctuations. When embankments are needed during the pavement construction, the soil must be compacted at a particular moisture-density condition to reach homogeneous properties. Due to construction variability, the as-compacted conditions might vary from the required specifications. This is of particular interest when dealing with compacted fine grained subgrade materials due to the influence of soil permeability in the seasonal moisture content fluctuation. The main objective of this study is the evaluation of the structural capacity and pavement performance due to the variability associated with the as-compacted moisture and density conditions, for different climatic regions. Three types of materials ranging from silt to clay were used in the analysis. Weather information from three locations was collected to represent different climate regimes. The pavement performance was analyzed using the Mechanistic-Empirical Pavement Design Guide (MEPDG) procedure by using the response of the pavement to three major distresses: fatigue cracking, rutting and thermal cracking. Two different levels of input accuracy were compared: Level 2, which uses simple index material and compaction properties and Level 3, which uses just the simple index material properties to estimate the resilient modulus. Results indicated that the soil compacted to optimum moisture content predicted less amount of distress when compared to the wet or dry optimum conditions for the low plasticity soils; whereas the predicted distresses increase with the increase in the as-compacted moisture content for the high plasticity soils. When compared with ratio of optimum condition, IRI had a maximum increase of 5% in Chicago and Atlanta region exhibited a fatigue cracking increase of 40% while Phoenix area showed a lot of rutting increase of 30%. The difference in the distress results obtained for Level 2 and Level 3 analyses were not significant for the soil compacted at optimum condition, but the dry and wet of optimum conditions resulted in significant larger differences that depended on the location or climate where the pavement is constructed.
- 8 February 2016
- Published by American Society of Civil Engineers (ASCE)
- p. 1303-1316
Effect of As-Compacted Moisture Content and Density on Pavement Performance in Different Climatic Regimes
While asphalt-concrete layer properties are more sensitive towards temperature variations, the subgrade stiffness have proven to be quite sensitive to moisture content fluctuations. When embankments are needed during the pavement construction, the soil must be compacted at a particular moisture-density condition to reach homogeneous properties. Due to construction variability, the as-compacted conditions might vary from the required specifications. This is of particular interest when dealing with compacted fine grained subgrade materials due to the influence of soil permeability in the seasonal moisture content fluctuation. The main objective of this study is the evaluation of the structural capacity and pavement performance due to the variability associated with the as-compacted moisture and density conditions, for different climatic regions. Three types of materials ranging from silt to clay were used in the analysis. Weather information from three locations was collected to represent different climate regimes. The pavement performance was analyzed using the Mechanistic-Empirical Pavement Design Guide (MEPDG) procedure by using the response of the pavement to three major distresses: fatigue cracking, rutting and thermal cracking. Two different levels of input accuracy were compared: Level 2, which uses simple index material and compaction properties and Level 3, which uses just the simple index material properties to estimate the resilient modulus. Results indicated that the soil compacted to optimum moisture content predicted less amount of distress when compared to the wet or dry optimum conditions for the low plasticity soils; whereas the predicted distresses increase with the increase in the as-compacted moisture content for the high plasticity soils. When compared with ratio of optimum condition, IRI had a maximum increase of 5% in Chicago and Atlanta region exhibited a fatigue cracking increase of 40% while Phoenix area showed a lot of rutting increase of 30%. The difference in the distress results obtained for Level 2 and Level 3 analyses were not significant for the soil compacted at optimum condition, but the dry and wet of optimum conditions resulted in significant larger differences that depended on the location or climate where the pavement is constructed.