André-Gilles Dumont
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
André-Gilles Dumont has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Adrien Houel
French Ministry of Transport, Motorway Concessions Control Service, bridge expert, Bron, France
1 shared publication - Ashish Bhaskar
Queensland University of Technology
1 shared publication - Edward Chung
The Hong Kong Polytechnic University
1 shared publication - Hervé Di Benedetto
University of Lyon/ENTPE
1 shared publication - Jacques Perret
NibuXs , Ch. des Triaudes 8, CH-1024 , Ecublens
1 shared publication - Laurent Arnaud
University of Lyon, Lyon, ENTPE, DGCB-LGM, Rue Maurice Audin , Vaulx-en-Velin, 69518, France
1 shared publication
Latest Publications
- 22 June 2014
- Published by Springer Nature in Materials and Structures
- Vol. 48 (9) , 2901-2913
Comparison of the two point bending and four point bending test methods for aged asphalt concrete field samples
- 22 June 2014
- Published by Springer Nature in Materials and Structures
- Vol. 48 (9) , 2901-2913
Comparison of the two point bending and four point bending test methods for aged asphalt concrete field samples
- 1 December 2010
- Published by Taylor & Francis in International Journal of Pavement Engineering
- Vol. 11 (6) , 441-447
Thermomechanical characterisation of asphalt pavements in laboratory conditions
Due to the viscoelastic properties of bituminous concrete, temperature changes result in significant mechanical effects. This paper proposes a method to assess, first, the intrinsic thermophysical parameters (thermal conductivity and heat capacity) of a bituminous mix, and then to characterise its mechanical behaviour by performing complex modulus tests. The determination of thermal properties of bituminous mixtures comes from an inverse analysis using finite-element software. The obtained intrinsic thermal parameters are essential for the fatigue law that depends on the viscous energy dissipation of bituminous concrete.
- 1 December 2010
- Published by Taylor & Francis in International Journal of Pavement Engineering
- Vol. 11 (6) , 441-447
Thermomechanical characterisation of asphalt pavements in laboratory conditions
Due to the viscoelastic properties of bituminous concrete, temperature changes result in significant mechanical effects. This paper proposes a method to assess, first, the intrinsic thermophysical parameters (thermal conductivity and heat capacity) of a bituminous mix, and then to characterise its mechanical behaviour by performing complex modulus tests. The determination of thermal properties of bituminous mixtures comes from an inverse analysis using finite-element software. The obtained intrinsic thermal parameters are essential for the fatigue law that depends on the viscous energy dissipation of bituminous concrete.
- 22 April 2010
- Published by Springer Nature in International Journal of Intelligent Transportation Systems Research
- Vol. 8 (3) , 151-163
Analysis for the Use of Cumulative Plots for Travel Time Estimation on Signalized Network
- 22 April 2010
- Published by Springer Nature in International Journal of Intelligent Transportation Systems Research
- Vol. 8 (3) , 151-163
Analysis for the Use of Cumulative Plots for Travel Time Estimation on Signalized Network
- 1 January 2004
- Published by Taylor & Francis in Road Materials and Pavement Design
- Vol. 5 (sup1) , 203-225
Strain and stress distributions in flexible pavements under moving loads
Calculated strain distributions in flexible pavements were studied by comparison with measurements made on full-scale structures. The calculated results were obtained by elastic and viscoelastic modelling of these structures. As no stress measurements were collected, the stress distribution was studied by comparing the results of elastic and viscoelastic calculations. For different loading and temperature conditions, and assuming the hypothesis of the French design method for flexible pavements, modelling provided strain signals similar to those measured on real scale structures for strains at two different depths in the studied structures. This first conclusion was used to validate the models, which were then used in the stress study. Some unexpected strains variations were observed near to the surface of the structures. Modelling based on linear elastic behaviour of the materials made it possible to explain these variations by analysing the stress variations, particularly in the vertical direction. Viscoelastic modelling have shown that some additional stresses appear in the bituminous layer when the loads are moving away from the measurement point. These stresses are induced mainly by the reaction of the foundation layers (sub-base and sub-grade) and they are mainly caused by the interaction between the layers of the structures. Finally, the analysis of the strain and stress distributions near to the surface showed that bituminous materials are submitted to higher horizontal than vertical stresses just under the truck wheel. A particular and unexpected result of this situation is that the vertical strains at just under the wheel are tensile ones.
- 1 January 2004
- Published by Taylor & Francis in Road Materials and Pavement Design
- Vol. 5 (sup1) , 203-225
Strain and stress distributions in flexible pavements under moving loads
Calculated strain distributions in flexible pavements were studied by comparison with measurements made on full-scale structures. The calculated results were obtained by elastic and viscoelastic modelling of these structures. As no stress measurements were collected, the stress distribution was studied by comparing the results of elastic and viscoelastic calculations. For different loading and temperature conditions, and assuming the hypothesis of the French design method for flexible pavements, modelling provided strain signals similar to those measured on real scale structures for strains at two different depths in the studied structures. This first conclusion was used to validate the models, which were then used in the stress study. Some unexpected strains variations were observed near to the surface of the structures. Modelling based on linear elastic behaviour of the materials made it possible to explain these variations by analysing the stress variations, particularly in the vertical direction. Viscoelastic modelling have shown that some additional stresses appear in the bituminous layer when the loads are moving away from the measurement point. These stresses are induced mainly by the reaction of the foundation layers (sub-base and sub-grade) and they are mainly caused by the interaction between the layers of the structures. Finally, the analysis of the strain and stress distributions near to the surface showed that bituminous materials are submitted to higher horizontal than vertical stresses just under the truck wheel. A particular and unexpected result of this situation is that the vertical strains at just under the wheel are tensile ones.
- 1 January 2004
- Published by Taylor & Francis in Road Materials and Pavement Design
- Vol. 5 (1) , 45-72
Thermomechanical and Mechanical Behaviour of Asphalt Mixtures at Cold Temperature
Temperature variations are particularly harmful to wearing courses with asphalt mixture. During wintertime, and especially, at very low temperatures, a surface cracking may appear and propagate more or less rapidly. An experimental investigation has been carried out on specimens of bituminous mixtures cored in the wearing course of 16 test sections of a motorway in Switzerland. These 16 wearing courses are composed with 16 different bitumen as pure bitumen, polymer modified bitumen and bitumen with additives. Those selected bitumen give a representation of the bitumen market in the 80's in Switzerland. 8 years after construction, bituminous mixtures specimens were cored in the driving carriageway and in the “emergency lane”, which is not driving Their thermomechanical behaviour through the Tensile Stress Restrained Specimens Test (TSRST), and their mechanical behaviour when subjected to mechanical load through a new highly precise Direct Tensile Test (DTT) were assessed. Significative behaviour, which was depending on the origin of the specimens (carriageway or emergency lane) were observed through the TSRST. In addition, this paper provides a relevant approach procedure for investigating thermal cracking at low temperature with a highly precise DTT.
- 1 January 2004
- Published by Taylor & Francis in Road Materials and Pavement Design
- Vol. 5 (1) , 45-72
Thermomechanical and Mechanical Behaviour of Asphalt Mixtures at Cold Temperature
Temperature variations are particularly harmful to wearing courses with asphalt mixture. During wintertime, and especially, at very low temperatures, a surface cracking may appear and propagate more or less rapidly. An experimental investigation has been carried out on specimens of bituminous mixtures cored in the wearing course of 16 test sections of a motorway in Switzerland. These 16 wearing courses are composed with 16 different bitumen as pure bitumen, polymer modified bitumen and bitumen with additives. Those selected bitumen give a representation of the bitumen market in the 80's in Switzerland. 8 years after construction, bituminous mixtures specimens were cored in the driving carriageway and in the “emergency lane”, which is not driving Their thermomechanical behaviour through the Tensile Stress Restrained Specimens Test (TSRST), and their mechanical behaviour when subjected to mechanical load through a new highly precise Direct Tensile Test (DTT) were assessed. Significative behaviour, which was depending on the origin of the specimens (carriageway or emergency lane) were observed through the TSRST. In addition, this paper provides a relevant approach procedure for investigating thermal cracking at low temperature with a highly precise DTT.