Emiliano Burresi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Emiliano Burresi has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Maria Lucia Protopapa
Italian National Agency for New Technologies, Energy and Sustainable Economic Development (ENEA), Laboratory Technologies for Waste and Secondary Raw Materials (RMP), Division Circular Economy (EC), Department for Sustainability (SSPT), Brindisi Research Center, S.S. 7 Appia km 706, 72100 Brindisi, Italy
5 shared publications - Anna Maria Laera
ENEA-Italian National Agency for New Technologies, Energy and Sustainable Economic Development, Brindisi Research Centre, S.S. 7, Km. 706, 72100 Brindisi, Italy
3 shared publications - Gennaro Cassano
ENEA—Italian National Agency for New Technologies, Energy and Sustainable Economic Development, Laboratory Functional Materials and Technologies for Sustainable Applications, Brindisi Research Centre, Strada Statale 7, Appia, Km. 706, I-72100 Brindisi, Italy
3 shared publications - Michele Penza
ENEA—Italian National Agency for New Technologies, Energy and Sustainable Economic Development, Laboratory Functional Materials and Technologies for Sustainable Applications, Brindisi Research Centre, Strada Statale 7, Appia, Km. 706, I-72100 Brindisi, Italy
3 shared publications - Massimo Celino
Italian National Agency for New Technologies, Energy and Sustainable Economic Development (ENEA)—C. R. Casaccia, Via Anguillarese 301, 00123 Rome, Italy
2 shared publications - A. Severino
STMicroelectronics 3 , Stradale Primosole 50, 95121 Catania
1 shared publication
Latest Publications
- Open Access
- 18 July 2025
- Published by MDPI AG in Chemengineering
- Vol. 9 (4) , 73
Fluorescent Moieties Through Alkaline Treatment of Graphene Oxide: A Potential Substitute to Replace CRM in wLEDS
White-light-emitting diodes (wLEDs) are central to next-generation lighting technologies, yet their reliance on critical raw materials (CRMs), such as rare-earth elements, raises concerns regarding sustainability and supply security. In this work, we present a simple, low-cost method to produce photoluminescent carbon-based nanostructures—known as oxidative debris (OD)—via alkaline treatment of graphene oxide (GO) using KOH solutions ranging from 0.04 M to 1.78 M. The resulting OD, isolated from the supernatant after acid precipitation, exhibits strong and tunable photoluminescence (PL) across the visible spectrum. Emission peaks shift from blue (~440 nm) to green (~500 nm) and yellow (~565 nm) as a function of treatment conditions, with excitation wavelengths between 300 and 390 nm. Optical, morphological. and compositional analyses were performed using UV-Vis, AFM, FTIR, and Raman spectroscopy, confirming the presence of highly oxidized aromatic domains. The blue-emitting (S2) and green/yellow-emitting (R2) fractions were successfully separated and characterized, demonstrating potential color tuning by adjusting KOH concentration and treatment time. This study highlights the feasibility of reusing GO-derived byproducts as sustainable phosphor alternatives in wLEDs, reducing reliance on CRMs and aligning with green chemistry principles.
- 18 July 2025
- Published by MDPI AG in Chemengineering
- Vol. 9 (4) , 73
Open AccessFluorescent Moieties Through Alkaline Treatment of Graphene Oxide: A Potential Substitute to Replace CRM in wLEDS
White-light-emitting diodes (wLEDs) are central to next-generation lighting technologies, yet their reliance on critical raw materials (CRMs), such as rare-earth elements, raises concerns regarding sustainability and supply security. In this work, we present a simple, low-cost method to produce photoluminescent carbon-based nanostructures—known as oxidative debris (OD)—via alkaline treatment of graphene oxide (GO) using KOH solutions ranging from 0.04 M to 1.78 M. The resulting OD, isolated from the supernatant after acid precipitation, exhibits strong and tunable photoluminescence (PL) across the visible spectrum. Emission peaks shift from blue (~440 nm) to green (~500 nm) and yellow (~565 nm) as a function of treatment conditions, with excitation wavelengths between 300 and 390 nm. Optical, morphological. and compositional analyses were performed using UV-Vis, AFM, FTIR, and Raman spectroscopy, confirming the presence of highly oxidized aromatic domains. The blue-emitting (S2) and green/yellow-emitting (R2) fractions were successfully separated and characterized, demonstrating potential color tuning by adjusting KOH concentration and treatment time. This study highlights the feasibility of reusing GO-derived byproducts as sustainable phosphor alternatives in wLEDs, reducing reliance on CRMs and aligning with green chemistry principles.
- Open Access
- 5 May 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 137 (17)
Lattice recovery and microstructural defects in thermally annealed phosphorous and aluminum implanted (0001) 4H-SiC
We report on the lattice strain and crystal defects generated in thermally annealed phosphorus and aluminum implanted (0001) 4° off-axis oriented homoepitaxial (0001)-4H-SiC (ion energy range between 30 and 200 keV). The partial crystal lattice recovery of the ion-implanted subsurface layer was achieved by thermal annealing processes in an inert gas atmosphere (Ar) in the temperature range between 1675 and 1825 °C, while the annealing time was kept constant at 15 (or 30) min. The lattice strain in ion-implanted 4H-SiC prior to and after thermal treatments was investigated in detail by high-resolution x-ray diffraction and reciprocal space mapping measurements. The thermal annealing processes reduce the lattice strain by a factor of 7, from 11.6 × 10−3 to about 1.6 × 10−3, and occur only along the [0001] axis, while the in-plane strain is negligible (< ±3 × 10−5) for all samples prior and after annealing. The determined lattice strain shows that the crystal lattice is not completely recovered, as also revealed by transmission electron microscopy observations and photoluminescence measurements. The thermal annealing induces and promotes the formation of point defect aggregates (mainly carbon-related vacancies, interstitials, and antisites) and nanoclusters with an average size between 5 and 20 nm.
- 5 May 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 137 (17)
Open AccessLattice recovery and microstructural defects in thermally annealed phosphorous and aluminum implanted (0001) 4H-SiC
We report on the lattice strain and crystal defects generated in thermally annealed phosphorus and aluminum implanted (0001) 4° off-axis oriented homoepitaxial (0001)-4H-SiC (ion energy range between 30 and 200 keV). The partial crystal lattice recovery of the ion-implanted subsurface layer was achieved by thermal annealing processes in an inert gas atmosphere (Ar) in the temperature range between 1675 and 1825 °C, while the annealing time was kept constant at 15 (or 30) min. The lattice strain in ion-implanted 4H-SiC prior to and after thermal treatments was investigated in detail by high-resolution x-ray diffraction and reciprocal space mapping measurements. The thermal annealing processes reduce the lattice strain by a factor of 7, from 11.6 × 10−3 to about 1.6 × 10−3, and occur only along the [0001] axis, while the in-plane strain is negligible (< ±3 × 10−5) for all samples prior and after annealing. The determined lattice strain shows that the crystal lattice is not completely recovered, as also revealed by transmission electron microscopy observations and photoluminescence measurements. The thermal annealing induces and promotes the formation of point defect aggregates (mainly carbon-related vacancies, interstitials, and antisites) and nanoclusters with an average size between 5 and 20 nm.
- Open Access
- 22 November 2024
- Published by MDPI AG in Chemosensors
- Vol. 12 (12) , 245
Flexible Humidity Sensor Based on Chemically Reduced Graphene Oxide
The accurate measurement of moisture content in pure gases and in gas mixtures, such as air, has great relevance in many industrial processes. In the present study, graphene oxide reduced through a mild alkaline treatment was used as a humidity sensing material to fabricate a flexible chemiresistive device operating at room temperature. The active layer was deposited by solution casting on a substrate of bimatted polyester, previously coated with inkjet-printed interdigitated electrodes made of silver. Structural investigations were performed by means of X-ray diffraction, Raman spectroscopy, and FTIR spectroscopy, while the optical properties were investigated using UV-VIS absorption and photoluminescence excitation spectroscopy. With increasing relative hu-midity from 0 to 80%, the electrical resistance decreased from about 1.4 GΩ to 2.5 MΩ. The ex-traordinarily large range of resistance values highlights the ultrahigh humidity sensitivity of re-duced graphene oxide, which acquires a fair amount of electrical conductivity after physisorption of water molecules but results in a highly resistive material in dry air. The high sensitivity at room temperature, the response’s repeatability, the wide relative humidity range detected, and the fast response time are the main advantages of the proposed humidity sensor, while the presence of some hysteresis, mainly at low relative humidity, and the recovery time need further improve-ment. Finally, the sensing mechanisms are briefly discussed.
- 22 November 2024
- Published by MDPI AG in Chemosensors
- Vol. 12 (12) , 245
Open AccessFlexible Humidity Sensor Based on Chemically Reduced Graphene Oxide
The accurate measurement of moisture content in pure gases and in gas mixtures, such as air, has great relevance in many industrial processes. In the present study, graphene oxide reduced through a mild alkaline treatment was used as a humidity sensing material to fabricate a flexible chemiresistive device operating at room temperature. The active layer was deposited by solution casting on a substrate of bimatted polyester, previously coated with inkjet-printed interdigitated electrodes made of silver. Structural investigations were performed by means of X-ray diffraction, Raman spectroscopy, and FTIR spectroscopy, while the optical properties were investigated using UV-VIS absorption and photoluminescence excitation spectroscopy. With increasing relative hu-midity from 0 to 80%, the electrical resistance decreased from about 1.4 GΩ to 2.5 MΩ. The ex-traordinarily large range of resistance values highlights the ultrahigh humidity sensitivity of re-duced graphene oxide, which acquires a fair amount of electrical conductivity after physisorption of water molecules but results in a highly resistive material in dry air. The high sensitivity at room temperature, the response’s repeatability, the wide relative humidity range detected, and the fast response time are the main advantages of the proposed humidity sensor, while the presence of some hysteresis, mainly at low relative humidity, and the recovery time need further improve-ment. Finally, the sensing mechanisms are briefly discussed.
- Open Access
- 9 October 2024
- Published by Elsevier in Carbon Trends
- Vol. 17
Optical investigation of degradation of graphene oxide in alkaline environment: Evidence of two distinct photon-emitting phases in visible region.
- 9 October 2024
- Published by Elsevier in Carbon Trends
- Vol. 17
Open AccessOptical investigation of degradation of graphene oxide in alkaline environment: Evidence of two distinct photon-emitting phases in visible region.
- Open Access
- 24 April 2024
- Published by MDPI AG in Proceedings
- Vol. 97 (1) , 204
Graphene Oxide-Based Flexible Sensors for Detection of Volatile Organic Compounds at Room Temperature
Flexible sensors, with an active layer made of graphene oxide (GO), were produced to detect volatile organic compounds (VOCs) at room temperature. Copper interdigitated electrodes were inkjet-printed on a substrate of bimatted polyester, and the direct drop-casting of a GO water solution was carried out to coat the devices. The performance of both commercial GO and GO synthesized by a modified Hummers’ method was investigated and compared. The oxygenated functional groups on the GO surface mainly enhance the selective sensing of polar analytes. The fabricated sensors exhibit the highest response towards alcohols, and minor sensitivity to esters, ketones, ethers and apolar petroleum ether.
- 24 April 2024
- Published by MDPI AG in Proceedings
- Vol. 97 (1) , 204
Open AccessGraphene Oxide-Based Flexible Sensors for Detection of Volatile Organic Compounds at Room Temperature
Flexible sensors, with an active layer made of graphene oxide (GO), were produced to detect volatile organic compounds (VOCs) at room temperature. Copper interdigitated electrodes were inkjet-printed on a substrate of bimatted polyester, and the direct drop-casting of a GO water solution was carried out to coat the devices. The performance of both commercial GO and GO synthesized by a modified Hummers’ method was investigated and compared. The oxygenated functional groups on the GO surface mainly enhance the selective sensing of polar analytes. The fabricated sensors exhibit the highest response towards alcohols, and minor sensitivity to esters, ketones, ethers and apolar petroleum ether.
- Open Access
- 18 September 2023
- Published by MDPI AG in Engineering Proceedings
- Vol. 48 (1) , 44
A Graphene Oxide Flexible Sensor for Humidity Detection
A flexible humidity sensor operating at room temperature was produced by direct drop casting of a graphene oxide (GO) water solution on a substrate of bimatted polyester, previously coated with inkjet-printed interdigitated electrodes in silver. The GO was synthesized by using a modified Hummers’ method, followed by an alkaline treatment with a water solution of KOH. Changes in the device resistance were measured for varying levels of relative humidity in the range from 15% to 70% in a sealed stainless cell. The device showed high sensitivity, good repeatability, and fast recovery time. Being flexible and robust, the proposed sensors could be easily integrated into wearable equipment.
- 18 September 2023
- Published by MDPI AG in Engineering Proceedings
- Vol. 48 (1) , 44
Open AccessA Graphene Oxide Flexible Sensor for Humidity Detection
A flexible humidity sensor operating at room temperature was produced by direct drop casting of a graphene oxide (GO) water solution on a substrate of bimatted polyester, previously coated with inkjet-printed interdigitated electrodes in silver. The GO was synthesized by using a modified Hummers’ method, followed by an alkaline treatment with a water solution of KOH. Changes in the device resistance were measured for varying levels of relative humidity in the range from 15% to 70% in a sealed stainless cell. The device showed high sensitivity, good repeatability, and fast recovery time. Being flexible and robust, the proposed sensors could be easily integrated into wearable equipment.
- Open Access
Lattice Strain Relaxation and Compositional Control in As-Rich GaAsP/(100)GaAs Heterostructures Grown by MOVPE
The fabrication of high-efficiency GaAsP-based solar cells on GaAs wafers requires addressing structural issues arising from the materials lattice mismatch. We report on tensile strain relaxation and composition control of MOVPE-grown As-rich GaAs1−xPx/(100)GaAs heterostructures studied by double-crystal X-ray diffraction and field emission scanning electron microscopy. Thin (80–150 nm) GaAs1−xPx epilayers appear partially relaxed (within 1−12% of the initial misfit) through a network of misfit dislocations along the sample and in plane directions. Values of the residual lattice strain as a function of epilayer thickness were compared with predictions from the equilibrium (Matthews–Blakeslee) and energy balance models. It is shown that the epilayers relax at a slower rate than expected based on the equilibrium model, an effect ascribed to the existence of an energy barrier to the nucleation of new dislocations. The study of GaAs1−xPx composition as a function of the V-group precursors ratio in the vapor during growth allowed for the determination of the As/P anion segregation coefficient. The latter agrees with values reported in the literature for P-rich alloys grown using the same precursor combination. P-incorporation into nearly pseudomorphic heterostructures turns out to be kinetically activated, with an activation energy EA = 1.41 ± 0.04 eV over the entire alloy compositional range.Open AccessLattice Strain Relaxation and Compositional Control in As-Rich GaAsP/(100)GaAs Heterostructures Grown by MOVPE
The fabrication of high-efficiency GaAsP-based solar cells on GaAs wafers requires addressing structural issues arising from the materials lattice mismatch. We report on tensile strain relaxation and composition control of MOVPE-grown As-rich GaAs1−xPx/(100)GaAs heterostructures studied by double-crystal X-ray diffraction and field emission scanning electron microscopy. Thin (80–150 nm) GaAs1−xPx epilayers appear partially relaxed (within 1−12% of the initial misfit) through a network of misfit dislocations along the sample and in plane directions. Values of the residual lattice strain as a function of epilayer thickness were compared with predictions from the equilibrium (Matthews–Blakeslee) and energy balance models. It is shown that the epilayers relax at a slower rate than expected based on the equilibrium model, an effect ascribed to the existence of an energy barrier to the nucleation of new dislocations. The study of GaAs1−xPx composition as a function of the V-group precursors ratio in the vapor during growth allowed for the determination of the As/P anion segregation coefficient. The latter agrees with values reported in the literature for P-rich alloys grown using the same precursor combination. P-incorporation into nearly pseudomorphic heterostructures turns out to be kinetically activated, with an activation energy EA = 1.41 ± 0.04 eV over the entire alloy compositional range. - 1 November 2013
- Published by American Scientific Publishers in Nanoscience and Nanotechnology Letters
- Vol. 5 (11) , 1182-1187
Surface States and Electronic Properties for Small Cadmium Sulfide Nanocluster
- 1 November 2013
- Published by American Scientific Publishers in Nanoscience and Nanotechnology Letters
- Vol. 5 (11) , 1182-1187
Surface States and Electronic Properties for Small Cadmium Sulfide Nanocluster
- 1 May 2012
- Published by Elsevier in Solid State Sciences
- Vol. 14 (5) , 567-573
Methodological approach to study energetic and structural properties of nanostructured cadmium sulfide by using ab-initio molecular dynamics simulations
- 1 May 2012
- Published by Elsevier in Solid State Sciences
- Vol. 14 (5) , 567-573
Methodological approach to study energetic and structural properties of nanostructured cadmium sulfide by using ab-initio molecular dynamics simulations