E. Yatsuka
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
E. Yatsuka has a total of 47 co-authors. Here are the top co-authors by number of shared publications:
T. Hatae
Japan Atomic Energy Agency, 801-1 Mukoyama, Naka, Ibaraki 311-0193, Japan
3 shared publicationsY. Kusama
Japan Atomic Energy Agency 1 , Naka, Ibaraki 311-0193, Japan
3 shared publicationsS. Suitoh
Showa Optronics, 1-22-1 Hakusan Midori-ku, Yokohama, Kanagawa 226-0006, Japan
2 shared publicationsA. Kurokawa
Showa Optronics 2 , Yokohama, Kanagawa 266-0006, Japan
1 shared publicationA.V. Zvonkov
1 shared publication- Anna Encheva
ITER Organization, CS 90 046, Saint Paul Lez Durance Cedex, France
1 shared publication
Latest Publications
- 1 January 2016
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 11 (1) , C01006
Development of laser beam injection system for the Edge Thomson Scattering (ETS) in ITER
This paper focuses on the design and development of the laser injection system for the ITER Edge Thomson Scattering system (ETS). The ITER ETS achieves a temporal resolution of 100 Hz by firing two 50 Hz laser beams alternatively. The use of dual lasers enables us to perform the Thomson scattering measurements at a temporal resolution of 50 Hz in case that one of the laser systems stops functioning. A new type of beam combiner was developed to obtain a single beam that is collinear and fixed linearly polarized from two laser beams using a motor-driven rotating half-wave plate. The rotating half-wave plate method does not induce misalignment even if the rotating mechanism malfunctions. The combined beam is relayed from the diagnostic hall to the plasma using mirror optics and is absorbed at the beam dump integrated on the inner blanket. The beam alignment system was designed to direct the laser beam onto the center of the beam dump head. The beam position at the beam dump is monitored by four alignment laser beams which propagate parallel to the diagnostic Nd:YAG laser beam and imaging systems installed outside the diagnostic port.
- 1 January 2016
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 11 (1) , C01006
Development of laser beam injection system for the Edge Thomson Scattering (ETS) in ITER
This paper focuses on the design and development of the laser injection system for the ITER Edge Thomson Scattering system (ETS). The ITER ETS achieves a temporal resolution of 100 Hz by firing two 50 Hz laser beams alternatively. The use of dual lasers enables us to perform the Thomson scattering measurements at a temporal resolution of 50 Hz in case that one of the laser systems stops functioning. A new type of beam combiner was developed to obtain a single beam that is collinear and fixed linearly polarized from two laser beams using a motor-driven rotating half-wave plate. The rotating half-wave plate method does not induce misalignment even if the rotating mechanism malfunctions. The combined beam is relayed from the diagnostic hall to the plasma using mirror optics and is absorbed at the beam dump integrated on the inner blanket. The beam alignment system was designed to direct the laser beam onto the center of the beam dump head. The beam position at the beam dump is monitored by four alignment laser beams which propagate parallel to the diagnostic Nd:YAG laser beam and imaging systems installed outside the diagnostic port.
- 1 December 2013
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 8 (12) , C12001
Progresses in development of the ITER edge Thomson scattering system
- 1 December 2013
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 8 (12) , C12001
Progresses in development of the ITER edge Thomson scattering system
- 17 July 2012
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 83 (10) , 10E328
Polychromator for the edge Thomson scattering system in ITER
A new type polychromator has been designed for the edge Thomson scattering system in ITER. Signal light is parallelly dispersed into two parts at the first interference filter. Spectral transmissivities for some spectral channels may enhance better than the conventional type polychromator. In the new type polychromator, the misalignment due to the machine accuracy is expected to be within the margin of APD area. In order to calibrate the spectral transmissivity using the dual-laser injection method during the plasma discharge, it is preferred that the spectral channels are separated at the geometric mean of the injected two wavelengths.
- 17 July 2012
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 83 (10) , 10E328
Polychromator for the edge Thomson scattering system in ITER
A new type polychromator has been designed for the edge Thomson scattering system in ITER. Signal light is parallelly dispersed into two parts at the first interference filter. Spectral transmissivities for some spectral channels may enhance better than the conventional type polychromator. In the new type polychromator, the misalignment due to the machine accuracy is expected to be within the margin of APD area. In order to calibrate the spectral transmissivity using the dual-laser injection method during the plasma discharge, it is preferred that the spectral channels are separated at the geometric mean of the injected two wavelengths.
- 1 August 2011
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 415 (1) , S1127-S1132
Plasma boundary and first-wall diagnostics in ITER
- 1 August 2011
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 415 (1) , S1127-S1132
Plasma boundary and first-wall diagnostics in ITER
- 1 October 2010
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 81 (10) , 10D541
Conceptual design of the collection optics for the edge Thomson scattering system in ITER
Neutron and gamma-ray irradiation complicates the design of the edge Thomson scattering (TS) system in ITER. The TS light is relayed through the relaying optics with labyrinth and fiber coupling optics. Electron density of is sufficient to measure and within a 10% and 5% margin of error, respectively, with a spatial resolution of 5 mm. This system can cover from 0.85 to 1 of the normalized minor radius. The time resolution is 10 ms, which is determined by the repetition rate of the laser device. A super-Gaussian is the ideal laser profile for the laser injection optics to avoid a breakdown of the filling gas used in density calibration through Raman scattering.- 1 October 2010
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 81 (10) , 10D541
Conceptual design of the collection optics for the edge Thomson scattering system in ITER
Neutron and gamma-ray irradiation complicates the design of the edge Thomson scattering (TS) system in ITER. The TS light is relayed through the relaying optics with labyrinth and fiber coupling optics. Electron density of is sufficient to measure and within a 10% and 5% margin of error, respectively, with a spatial resolution of 5 mm. This system can cover from 0.85 to 1 of the normalized minor radius. The time resolution is 10 ms, which is determined by the repetition rate of the laser device. A super-Gaussian is the ideal laser profile for the laser injection optics to avoid a breakdown of the filling gas used in density calibration through Raman scattering.