John L. Barber
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
John L. Barber has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Berni J. Alder
Lawrence Livermore National Laboratory P.O.Box 808 94551-9900 Livermore CA USA
2 shared publications - Timothy Clark Germann
Los Alamos National Laboratory
2 shared publications - Andrew F. T. Leong
Los Alamos National Laboratory 3 , Los Alamos, New Mexico 87545
1 shared publication - Brendt Wohlberg
Los Alamos National Laboratory, Los Alamos, NM, USA
1 shared publication - Bryan Zuanetti
Los Alamos National Laboratory
1 shared publication - Christopher S. Meredith
DEVCOM Army Research Laboratory
1 shared publication
Latest Publications
- 29 March 2024
- Published by Springer Nature
- p. 111-117
Interrogating the Effects of Rate and Orientation on the Dynamic Failure Response of α-Quartz under Uniaxial Stress Compression
- 29 March 2024
- Published by Springer Nature
- p. 111-117
Interrogating the Effects of Rate and Orientation on the Dynamic Failure Response of α-Quartz under Uniaxial Stress Compression
- 12 May 2014
- Published by American Physical Society (APS) in Physical Review B
- Vol. 89 (18)
Diffractive imaging at large Fresnel number: Challenge of dynamic mesoscale imaging with hard x rays
Real materials have structure at both the atomic or crystalline scale as well as at interfaces and defects at the larger scale of grains. There is a need for the study of materials at the ``mesoscale,'' the scale at which subgranular physical processes and intergranular organization couple to determine microstructure, crucially impacting constitutive response at the engineering macroscale. Diffractive imaging using photons that can penetrate multiple grains of material would be a transformative technique for the study of the performance of materials in dynamic extremes. Thicker samples imply higher energy photons of shorter wavelength, and imaging of multiple grains implies bigger spot sizes. Such imaging requires the use of future planned and proposed hard x-ray free electron lasers (such as the European XFEL) to provide both the spatial coherence transverse to the large spots and the peak brilliance to provide the short illumination times. The result is that the Fresnel number of the system becomes large and is no longer in the Fraunhofer far-field limit. The interrelated issues of diffractive imaging at large Fresnel number are analyzed, including proof that diffractive imaging is possible in this limit and estimates of the signal-to-noise possible. In addition, derivation of the heating rates for brilliant pulses of x rays are presented. The potential and limitations on multiple dynamic images are derived. This paper will present a study of x-ray interactions with materials in this new regime of spatially coherent but relatively large mesoscale spots at very hard energies. It should provide the theory and design background for the experiments and facilities required to control materials in extreme environments, in particular for the next generation of very-hard-x-ray free electron lasers.
- 12 May 2014
- Published by American Physical Society (APS) in Physical Review B
- Vol. 89 (18)
Diffractive imaging at large Fresnel number: Challenge of dynamic mesoscale imaging with hard x rays
Real materials have structure at both the atomic or crystalline scale as well as at interfaces and defects at the larger scale of grains. There is a need for the study of materials at the ``mesoscale,'' the scale at which subgranular physical processes and intergranular organization couple to determine microstructure, crucially impacting constitutive response at the engineering macroscale. Diffractive imaging using photons that can penetrate multiple grains of material would be a transformative technique for the study of the performance of materials in dynamic extremes. Thicker samples imply higher energy photons of shorter wavelength, and imaging of multiple grains implies bigger spot sizes. Such imaging requires the use of future planned and proposed hard x-ray free electron lasers (such as the European XFEL) to provide both the spatial coherence transverse to the large spots and the peak brilliance to provide the short illumination times. The result is that the Fresnel number of the system becomes large and is no longer in the Fraunhofer far-field limit. The interrelated issues of diffractive imaging at large Fresnel number are analyzed, including proof that diffractive imaging is possible in this limit and estimates of the signal-to-noise possible. In addition, derivation of the heating rates for brilliant pulses of x rays are presented. The potential and limitations on multiple dynamic images are derived. This paper will present a study of x-ray interactions with materials in this new regime of spatially coherent but relatively large mesoscale spots at very hard energies. It should provide the theory and design background for the experiments and facilities required to control materials in extreme environments, in particular for the next generation of very-hard-x-ray free electron lasers.
- 1 October 2013
- Published by IOP Publishing in Modelling and Simulation in Materials Science and Engineering
- Vol. 21 (7) , 75013
The theoretical strength of rubber: numerical simulations of polyisoprene networks at high tensile strains evidence the role of average chain tortuosity
The ultimate stress and strain of polyisoprene rubber were studied by numerical simulations of three-dimensional random networks, subjected to tensile strains high enough to cause chain rupture. Previously published molecular chain force extension models and a numerical network construction procedure were used to perform the simulations for network crosslink densities between 2 × 1019 and 1 × 1020 cm−3, corresponding to experimental dicumyl-peroxide concentrations of 1–5 parts per hundred. At tensile failure (defined as the point of maximum stress), we find that the fraction of network chains ruptured is between 0.1% and 1%, depending on the crosslink density. The fraction of network chains that are taut, i.e. their end-to-end distance is greater than their unstretched contour length, ranges between 10% and 15% at failure. Our model predicts that the theoretical (defect-free) failure stress should be about twice the highest experimental value reported. For extensions approaching failure, tensile stress is dominated by the network morphology and purely enthalpic bond distortion forces and, in this regime, the model has essentially no free parameters. The average initial chain tortuosity (τ) appears to be an important statistical property of rubber networks; if the stress is scaled by τ and the tensile strain is scaled by τ−1, we obtain a master curve for stress versus strain, valid for all crosslink densities. We derive an analytic expression for the average tortuosity, which is in agreement with values calculated in the simulations.
- 1 October 2013
- Published by IOP Publishing in Modelling and Simulation in Materials Science and Engineering
- Vol. 21 (7) , 75013
The theoretical strength of rubber: numerical simulations of polyisoprene networks at high tensile strains evidence the role of average chain tortuosity
The ultimate stress and strain of polyisoprene rubber were studied by numerical simulations of three-dimensional random networks, subjected to tensile strains high enough to cause chain rupture. Previously published molecular chain force extension models and a numerical network construction procedure were used to perform the simulations for network crosslink densities between 2 × 1019 and 1 × 1020 cm−3, corresponding to experimental dicumyl-peroxide concentrations of 1–5 parts per hundred. At tensile failure (defined as the point of maximum stress), we find that the fraction of network chains ruptured is between 0.1% and 1%, depending on the crosslink density. The fraction of network chains that are taut, i.e. their end-to-end distance is greater than their unstretched contour length, ranges between 10% and 15% at failure. Our model predicts that the theoretical (defect-free) failure stress should be about twice the highest experimental value reported. For extensions approaching failure, tensile stress is dominated by the network morphology and purely enthalpic bond distortion forces and, in this regime, the model has essentially no free parameters. The average initial chain tortuosity (τ) appears to be an important statistical property of rubber networks; if the stress is scaled by τ and the tensile strain is scaled by τ−1, we obtain a master curve for stress versus strain, valid for all crosslink densities. We derive an analytic expression for the average tortuosity, which is in agreement with values calculated in the simulations.
- 27 October 2008
- Published by American Physical Society (APS) in Physical Review E
- Vol. 78 (4) , 045301
Scaling of atomistic fluid dynamics simulations
We have performed a series of large-scale atomistic simulations of the Rayleigh-Taylor instability including up to particles and spanning time and length scales of up to and , respectively. The results suggest that atomistic fluid dynamics simulations exhibit the same scaling as solutions of the continuum Navier-Stokes equations. Furthermore, a comparison with macroscopic Rayleigh-Taylor experiments suggests that the results of such atomistic simulations can, in fact, be scaled up to macroscopic dimensions, even for complex, nonstationary flows.- 27 October 2008
- Published by American Physical Society (APS) in Physical Review E
- Vol. 78 (4) , 045301
Scaling of atomistic fluid dynamics simulations
We have performed a series of large-scale atomistic simulations of the Rayleigh-Taylor instability including up to particles and spanning time and length scales of up to and , respectively. The results suggest that atomistic fluid dynamics simulations exhibit the same scaling as solutions of the continuum Navier-Stokes equations. Furthermore, a comparison with macroscopic Rayleigh-Taylor experiments suggests that the results of such atomistic simulations can, in fact, be scaled up to macroscopic dimensions, even for complex, nonstationary flows.- 9 April 2008
- Published by American Physical Society (APS) in Physical Review B
- Vol. 77 (14) , 144106
Shock-front broadening in polycrystalline materials
We analyze a model for the evolution of shock fronts in polycrystalline materials. This model is based on the idea of Meyers and Carvalho [Mater. Sci. Eng. 24, 131 (1976)] that the shock velocity anisotropy within the polycrystal is the most important factor in shock front broadening. Our analysis predicts that the shock front width increases as the power of the front penetration distance into the crystal. Our theoretical prediction is in plausible agreement with previous experimental results for the elastic precursor rise time, and it should therefore provide a useful shock width estimate. Furthermore, our theoretical framework is also applicable to other problems involving front propagation in heterogeneous media.- 9 April 2008
- Published by American Physical Society (APS) in Physical Review B
- Vol. 77 (14) , 144106
Shock-front broadening in polycrystalline materials
We analyze a model for the evolution of shock fronts in polycrystalline materials. This model is based on the idea of Meyers and Carvalho [Mater. Sci. Eng. 24, 131 (1976)] that the shock velocity anisotropy within the polycrystal is the most important factor in shock front broadening. Our analysis predicts that the shock front width increases as the power of the front penetration distance into the crystal. Our theoretical prediction is in plausible agreement with previous experimental results for the elastic precursor rise time, and it should therefore provide a useful shock width estimate. Furthermore, our theoretical framework is also applicable to other problems involving front propagation in heterogeneous media.- 1 January 2008
- Published by AIP Publishing in AIP Conference Proceedings
SIMULATION OF FLUID INSTABILITIES USING ATOMISTIC METHODS
We illustrate the present state of the art in large‐scale atomistic simulations through various direct simulation Monte‐Carlo calculations of the Rayleigh‐Taylor and Richtmyer‐Meshkov instabilities. The results are qualitatively and quantitatively analyzed, and compared with previous Navier‐Stokes‐based theory and simulations. We find that large particle‐based simulations are able to capture both traditional hydrodynamic behavior as well as small‐scale atomistic effects.
- 1 January 2008
- Published by AIP Publishing in AIP Conference Proceedings
SIMULATION OF FLUID INSTABILITIES USING ATOMISTIC METHODS
We illustrate the present state of the art in large‐scale atomistic simulations through various direct simulation Monte‐Carlo calculations of the Rayleigh‐Taylor and Richtmyer‐Meshkov instabilities. The results are qualitatively and quantitatively analyzed, and compared with previous Navier‐Stokes‐based theory and simulations. We find that large particle‐based simulations are able to capture both traditional hydrodynamic behavior as well as small‐scale atomistic effects.