A. Haibel
A. Haibel has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- John Banhart
Helmholtz-Zentrum Berlin für Materialien und Energie GmbH
2 shared publications A. Melzer
Grillo-Werke AG, Metal Division, Goslar 38644, Germany
1 shared publicationA. Schreyer
GKSS Research Centre Geesthacht
1 shared publicationB. Kieback
Technical University Dresden, Institute of Materials Science, Dresden, Germany
1 shared publicationF. Beckmann
GKSS Research Centre Geesthacht
1 shared publicationF. Henkel
FRM II, Garching, Germany
1 shared publication
Latest Publications
- 1 June 2010
- Published by Cambridge University Press (CUP) in Powder Diffraction
- Vol. 25 (2) , 161-164
Latest developments in microtomography and nanotomography at PETRA III
Due to the extraordinary beam characteristics of the new PETRA III synchrotron, i.e., the high brilliance, the extremely low emittance of 1 nm rad, and the high fraction of coherent photons even in the hard X-ray range, the imaging beamline (IBL) at PETRA III will provide state of the art imaging and tomography capabilities with resolution well into the nanometer range. Novel applications of tomographic techniques allow for high speed in situ measurements as well as highest spatial and density resolutions. Additionally, the highly coherent beam enables the application of phase contrast methods in an exceptional way. Since the focus is on the energy range between 5 and 50 keV, the IBL will among others be ideally suited for microtomography and nanotomography on small engineering materials science samples as well as for studying soft matter, bones, medical implants, and biomatter.
- 1 June 2010
- Published by Cambridge University Press (CUP) in Powder Diffraction
- Vol. 25 (2) , 161-164
Latest developments in microtomography and nanotomography at PETRA III
Due to the extraordinary beam characteristics of the new PETRA III synchrotron, i.e., the high brilliance, the extremely low emittance of 1 nm rad, and the high fraction of coherent photons even in the hard X-ray range, the imaging beamline (IBL) at PETRA III will provide state of the art imaging and tomography capabilities with resolution well into the nanometer range. Novel applications of tomographic techniques allow for high speed in situ measurements as well as highest spatial and density resolutions. Additionally, the highly coherent beam enables the application of phase contrast methods in an exceptional way. Since the focus is on the energy range between 5 and 50 keV, the IBL will among others be ideally suited for microtomography and nanotomography on small engineering materials science samples as well as for studying soft matter, bones, medical implants, and biomatter.
- 1 January 2010
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 157 (4) , A387-A391
In Situ Microtomographic Monitoring of Discharging Processes in Alkaline Cells
Alkaline batteries have been in use for about 100 years. They show excellent performance characteristics, a favorable cost structure, and are extremely reliable [ Solid State Ionics , 134 , 139 (2000) ; J. Power Sources , 127 , 45 (2004) ; J. Power Sources , 103 , 120 (2001) ; J. Power Sources , 105 , 127 (2002) ]. The lifetime is strongly correlated with the dissolution process of the zinc particles in the anode material and the deoxidation of the manganese dioxide in the cathode material [ Power Sources 7 , Academic , New York (1979) ; J. Power Sources , 77 , 127 (1999) ; J. Electrochem. Soc. , 154 , A481 (2007) ; J. Electrochem. Soc. , 152 , A1930 (2005) ; J. Power Sources , 186 , 532 (2009) ; J. Power Sources , 156 , 692 (2006) ]. Parameters that affect the zinc utilization still have to be identified and optimized to continue the improvement of the cell performance [ J. Power Sources , 96 , 133 (2001) ]. By in situ synchrotron tomography, the discharging process of an alkaline cell LR61 AAAA VARTA HighEnergy was visualized and analyzed quantitatively. The focus of attention was the observation of the zinc particles in the anode electrolyte material. The complete dissolution process of these zinc particles, i.e., the morphology and spatial distribution of zinc and zinc oxide, during discharging was discussed.
- 1 January 2010
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 157 (4) , A387-A391
In Situ Microtomographic Monitoring of Discharging Processes in Alkaline Cells
Alkaline batteries have been in use for about 100 years. They show excellent performance characteristics, a favorable cost structure, and are extremely reliable [ Solid State Ionics , 134 , 139 (2000) ; J. Power Sources , 127 , 45 (2004) ; J. Power Sources , 103 , 120 (2001) ; J. Power Sources , 105 , 127 (2002) ]. The lifetime is strongly correlated with the dissolution process of the zinc particles in the anode material and the deoxidation of the manganese dioxide in the cathode material [ Power Sources 7 , Academic , New York (1979) ; J. Power Sources , 77 , 127 (1999) ; J. Electrochem. Soc. , 154 , A481 (2007) ; J. Electrochem. Soc. , 152 , A1930 (2005) ; J. Power Sources , 186 , 532 (2009) ; J. Power Sources , 156 , 692 (2006) ]. Parameters that affect the zinc utilization still have to be identified and optimized to continue the improvement of the cell performance [ J. Power Sources , 96 , 133 (2001) ]. By in situ synchrotron tomography, the discharging process of an alkaline cell LR61 AAAA VARTA HighEnergy was visualized and analyzed quantitatively. The focus of attention was the observation of the zinc particles in the anode electrolyte material. The complete dissolution process of these zinc particles, i.e., the morphology and spatial distribution of zinc and zinc oxide, during discharging was discussed.
- 6 June 2009
- Published by International Union of Crystallography (IUCr) in Journal of Synchrotron Radiation
- Vol. 16 (4) , 524-527
A 1800 K furnace designed forin situsynchrotron microtomography
A radiation furnace that covers the temperature range from room temperature up to 1800 K has been designed and constructed for in situ synchrotron microtomography. The furnace operates under a vacuum or under any inert gas atmosphere. The two 1000 W halogen heating lamps are water- and air-cooled. The samples are located at the focus of these lamp reflectors on a rotary feedthrough that is connected to a driving rotation stage below the furnace. The X-ray beam penetrates the furnace through two X-ray-transparent vacuum-sealed windows. Further windows can be used for temperature control, sample changing and gas inflow and outflow.
- 6 June 2009
- Published by International Union of Crystallography (IUCr) in Journal of Synchrotron Radiation
- Vol. 16 (4) , 524-527
A 1800 K furnace designed forin situsynchrotron microtomography
A radiation furnace that covers the temperature range from room temperature up to 1800 K has been designed and constructed for in situ synchrotron microtomography. The furnace operates under a vacuum or under any inert gas atmosphere. The two 1000 W halogen heating lamps are water- and air-cooled. The samples are located at the focus of these lamp reflectors on a rotary feedthrough that is connected to a driving rotation stage below the furnace. The X-ray beam penetrates the furnace through two X-ray-transparent vacuum-sealed windows. Further windows can be used for temperature control, sample changing and gas inflow and outflow.