Jean-Pierre de Vaujany
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Jean-Pierre de Vaujany has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Michèle Guingand
Université de Lyon, INSA-Lyon
9 shared publications - Didier Rémond
INSA Lyon, CNRS, LaMCoS, UMR5259
4 shared publications - Yvan Icard
Stress Department, EADS Eurocopter, 13725 Marignane, France
3 shared publications Miche`le Guingand
INSA of Lyon, Villeurbanne, France
2 shared publicationsMichèle Guingand
INSA of Lyon, Villeurbanne, France
2 shared publications- Yann Hiltcher
LDMS Laboratory, Bâtiment J. d’Alembert—INSA of Lyon, 20, av. A. Einstein, 69621 Villeurbanne, France
2 shared publications
Latest Publications
- Open Access
- 17 February 2022
- Published by EDP Sciences in Mechanics & Industry
- Vol. 23, 6
Modelling of elastoplastic, multi-scale and multi-contact problems: application to worm gears
A nonconventional application of worm gears exploits the irreversibility of these power transmission devices in order to realize fast emergency braking. This application can be used to secure lifting devices. A limiting factor in the design of these instantaneous braking systems is the residual deformations of the worm/wheel contacting teeth, due to the impact between them at each emergency stop. The prediction of these residual displacements requires solving of an elastic–plastic, multi-scale and multi-contact problem. Original numerical tools were developed in this study to solve the problem at global and local scales. The method has been validated by comparing the obtained results with 3D measurements on new and deformed worm/wheel pairs. In order to predict the issue of the worm gear after an impact, a criterion based on kinematic errors is proposed. Applying this criterion gives the maximal admissible torque for the braking system to be operational after the impact.
- 17 February 2022
- Published by EDP Sciences in Mechanics & Industry
- Vol. 23, 6
Open AccessModelling of elastoplastic, multi-scale and multi-contact problems: application to worm gears
A nonconventional application of worm gears exploits the irreversibility of these power transmission devices in order to realize fast emergency braking. This application can be used to secure lifting devices. A limiting factor in the design of these instantaneous braking systems is the residual deformations of the worm/wheel contacting teeth, due to the impact between them at each emergency stop. The prediction of these residual displacements requires solving of an elastic–plastic, multi-scale and multi-contact problem. Original numerical tools were developed in this study to solve the problem at global and local scales. The method has been validated by comparing the obtained results with 3D measurements on new and deformed worm/wheel pairs. In order to predict the issue of the worm gear after an impact, a criterion based on kinematic errors is proposed. Applying this criterion gives the maximal admissible torque for the braking system to be operational after the impact.
- 26 January 2017
- Published by EDP Sciences in Mechanics & Industry
- Vol. 18 (2) , 202
Quasi-static analysis of spline coupling under load
This paper presents a procedure for analyzing the instantaneous loaded contact of the spline joints. The process permits very fast computation of load sharing, including bending and contact effects. It uses the method of the influence coefficients resolving the equation of compatibility of the displacements. A study of the numerical model allows to show the influence of the deformation of the shafts and of the mounting errors on the contact pressure distribution.
- 26 January 2017
- Published by EDP Sciences in Mechanics & Industry
- Vol. 18 (2) , 202
Quasi-static analysis of spline coupling under load
This paper presents a procedure for analyzing the instantaneous loaded contact of the spline joints. The process permits very fast computation of load sharing, including bending and contact effects. It uses the method of the influence coefficients resolving the equation of compatibility of the displacements. A study of the numerical model allows to show the influence of the deformation of the shafts and of the mounting errors on the contact pressure distribution.
- 3 September 2016
- Published by Springer Nature
- p. 737-745
Design and analysis of a spiral bevel gear
- 13 August 2014
- Published by Springer Nature in Applied Composite Materials
- Vol. 22 (4) , 343-362
Quasi-static Load Sharing Model in the Case of Moulded Glass Fibre Reinforced Polyamide 6 Gears
- 13 August 2014
- Published by Springer Nature in Applied Composite Materials
- Vol. 22 (4) , 343-362
Quasi-static Load Sharing Model in the Case of Moulded Glass Fibre Reinforced Polyamide 6 Gears
- 7 January 2013
- Published by Wiley in Journal of Mechanical Design
- Vol. 135 (2) , 024502
Designing and Manufacturing Spiral Bevel Gears Using 5-Axis Computer Numerical Control (CNC) Milling Machines
The design of spiral bevel gears remains complex since tooth geometry and the resulting kinematic performance stem directly from the manufacturing process. Spiral bevel gear cutting up to now has relied on the works of several manufacturers. Recent advances in milling machine technology and computer aided manufacturing (CAM) now make it possible to manufacture good quality spiral bevel gears on a standard 5-axis milling machine. This paper describes the computer aided design (CAD) definition and manufacturing of spiral bevel gear tooth surfaces. Process performance is assessed by comparing the resulting surfaces after machining with the predefined CAD surfaces. This manufacturing process makes it possible to obtain geometry analytically, making design easier than with standard spiral bevel gears.
- 7 January 2013
- Published by Wiley in Journal of Mechanical Design
- Vol. 135 (2) , 024502
Designing and Manufacturing Spiral Bevel Gears Using 5-Axis Computer Numerical Control (CNC) Milling Machines
The design of spiral bevel gears remains complex since tooth geometry and the resulting kinematic performance stem directly from the manufacturing process. Spiral bevel gear cutting up to now has relied on the works of several manufacturers. Recent advances in milling machine technology and computer aided manufacturing (CAM) now make it possible to manufacture good quality spiral bevel gears on a standard 5-axis milling machine. This paper describes the computer aided design (CAD) definition and manufacturing of spiral bevel gear tooth surfaces. Process performance is assessed by comparing the resulting surfaces after machining with the predefined CAD surfaces. This manufacturing process makes it possible to obtain geometry analytically, making design easier than with standard spiral bevel gears.
- 21 August 2008
- Published by Wiley in Journal of Mechanical Design
- Vol. 130 (10) , 104502
Face Gear Width Prediction Using the DOE Method
This paper deals with face gear design. The goal is to propose a simple formula for predicting the width of the wheel as a function of the main design parameters. A specific software was used to achieve this goal. This numerical tool is able to simulate the geometry and the quasistatic loaded behavior of a face gear. The statistical method used for analyzing the influence of data is described: The design of experiments leads to a simple regression model taking into account the influential parameters and their couplings. In the last part of this paper, the results of the formulas are compared to those of the software and an optimal design is proposed based on the regression model.
- 21 August 2008
- Published by Wiley in Journal of Mechanical Design
- Vol. 130 (10) , 104502
Face Gear Width Prediction Using the DOE Method
This paper deals with face gear design. The goal is to propose a simple formula for predicting the width of the wheel as a function of the main design parameters. A specific software was used to achieve this goal. This numerical tool is able to simulate the geometry and the quasistatic loaded behavior of a face gear. The statistical method used for analyzing the influence of data is described: The design of experiments leads to a simple regression model taking into account the influential parameters and their couplings. In the last part of this paper, the results of the formulas are compared to those of the software and an optimal design is proposed based on the regression model.
- 14 April 2008
- Published by Wiley in Journal of Mechanical Design
- Vol. 130 (6) , 062602
Numerical and Experimental Study of the Loaded Transmission Error of a Worm Gear With a Plastic Wheel
Nowadays, the wheels of worm gears with a low module can be made of plastic; thus, classical modeling can no longer be used satisfactorily. The present paper describes an original method for studying the quasistatic loaded behavior of a worm gear, with a steel worm and a nylon wheel. A generalized Kelvin model is proposed, and the computation of load sharing is described by using an equation of displacement compatibility. The history of previous deformation and the effect of the nylon’s structural damping are also taken into account. Experimental measurements of the loaded transmission error are performed with the help of optical encoders rigidly connected to the worm and gear shafts, giving access to their instantaneous angular positions. The numerical simulations fit quite well with the experimental results.
- 14 April 2008
- Published by Wiley in Journal of Mechanical Design
- Vol. 130 (6) , 062602
Numerical and Experimental Study of the Loaded Transmission Error of a Worm Gear With a Plastic Wheel
Nowadays, the wheels of worm gears with a low module can be made of plastic; thus, classical modeling can no longer be used satisfactorily. The present paper describes an original method for studying the quasistatic loaded behavior of a worm gear, with a steel worm and a nylon wheel. A generalized Kelvin model is proposed, and the computation of load sharing is described by using an equation of displacement compatibility. The history of previous deformation and the effect of the nylon’s structural damping are also taken into account. Experimental measurements of the loaded transmission error are performed with the help of optical encoders rigidly connected to the worm and gear shafts, giving access to their instantaneous angular positions. The numerical simulations fit quite well with the experimental results.
- 1 March 2006
- Published by Wiley in Journal of Mechanical Design
- Vol. 129 (1) , 23-30
Load Sharing of Worm Gear With a Plastic Wheel
The material of the wheel in a worm gear has to be nonrigid due to very high sliding velocity. Such gears are currently made of plastic in the case of a small module. The present paper describes an original method for studying the quasi-static loaded behavior of a worm gear, with a steel worm and a nylon wheel. Plastics are viscoelastic materials and do not obey Hooke’s law. This paper describes an elaborated method that is a generalization of Kelvin’s model. The computation also uses experimental tests to obtain data relating to the plastic. The computation of the load sharing is described and uses the equation of displacement compatibility. The history of previous deformation and the effect of the nylon’s structural damping are taken into account. At a given constant temperature, the load sharing, meshing stiffness, and loaded transmission error depend on the driving torque and time, that is to say speed of rotation.
- 1 March 2006
- Published by Wiley in Journal of Mechanical Design
- Vol. 129 (1) , 23-30
Load Sharing of Worm Gear With a Plastic Wheel
The material of the wheel in a worm gear has to be nonrigid due to very high sliding velocity. Such gears are currently made of plastic in the case of a small module. The present paper describes an original method for studying the quasi-static loaded behavior of a worm gear, with a steel worm and a nylon wheel. Plastics are viscoelastic materials and do not obey Hooke’s law. This paper describes an elaborated method that is a generalization of Kelvin’s model. The computation also uses experimental tests to obtain data relating to the plastic. The computation of the load sharing is described and uses the equation of displacement compatibility. The history of previous deformation and the effect of the nylon’s structural damping are taken into account. At a given constant temperature, the load sharing, meshing stiffness, and loaded transmission error depend on the driving torque and time, that is to say speed of rotation.
- 1 February 2006
- Published by Wiley in Journal of Mechanical Design
- Vol. 129 (2) , 195-200
Numerical and Experimental Study of the Loaded Transmission Error of a Spiral Bevel Gear
The design of spiral bevel gears in aeronautical gear boxes requires very precise and realistic numerical simulations. One important criteria is the loaded transmission error (LTE) that gear designers attempt to reduce at the nominal torque. This paper presents a numerical tool that simulates the loaded meshing of spiral bevel gears and experimental tests carried out on a real helicopter gear box. Tooth profile is defined by the Gleason cutting process and tooth bending effects and contact deformations are both taken into account. The bending effect computation uses a three-dimensional finite element model, while the contact deformations are obtained by using Boussinesq’s theory. Experimental measurements of the LTE were performed using magnetic and optical encoders rigidly connected with the pinion and gear shafts, giving access to the records of the instantaneous angular positions. The numerical simulations fit quite well the experimental results.
- 1 February 2006
- Published by Wiley in Journal of Mechanical Design
- Vol. 129 (2) , 195-200
Numerical and Experimental Study of the Loaded Transmission Error of a Spiral Bevel Gear
The design of spiral bevel gears in aeronautical gear boxes requires very precise and realistic numerical simulations. One important criteria is the loaded transmission error (LTE) that gear designers attempt to reduce at the nominal torque. This paper presents a numerical tool that simulates the loaded meshing of spiral bevel gears and experimental tests carried out on a real helicopter gear box. Tooth profile is defined by the Gleason cutting process and tooth bending effects and contact deformations are both taken into account. The bending effect computation uses a three-dimensional finite element model, while the contact deformations are obtained by using Boussinesq’s theory. Experimental measurements of the LTE were performed using magnetic and optical encoders rigidly connected with the pinion and gear shafts, giving access to the records of the instantaneous angular positions. The numerical simulations fit quite well the experimental results.