Olivier Léonard
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Olivier Léonard has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Sébastien Borguet
Turbomachinery Group, University of Liège, Campus du Sart-Tilman, B52/3, Liège 4000, Belgium
8 shared publications - J. P. Thomas
Turbomachinery Group, University of Liège, Chemin des Chevreuils 1, B-4000 Liège, Belgium
3 shared publications - Pierre Dewallef
Laboratory of Thermodynamics, University of Liège, Campus du Sart-Tilman, B49, Liège 4000, Belgium
3 shared publications - W. Du
Institute of Engineering Thermophysics, Chinese Academy of Sciences, China
3 shared publications - Jean-François Simon
Techspace Aero, Safran Group, Route de Liers 121, B-4041 Milmort, Belgium
2 shared publications C. Romessis
Laboratory of Thermal Turbomachines, National Technical University of Athens, P.O. Box 64069, Athens 15710, Greece
1 shared publication
Latest Publications
- 1 September 2015
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 138 (2) , 021201
Regression-Based Modeling of a Fleet of Gas Turbine Engines for Performance Trending
Module performance analysis is a well-established framework to assess changes in the health condition of the components of the engine gas-path. The primary material of the technique is the so-called vector of residuals, which are built as the difference between actual measurement taken in the gas-path and the values predicted by means of an engine model. Obviously, the quality of the assessment of the engine condition depends strongly on the accuracy of the engine model. The present paper proposes a new approach for data-driven modeling of a fleet of engines of a given type. Such black-box models can be designed by operators, such as airlines and third-party companies. The fleet-wide modeling process is formulated as a regression problem that provides a dedicated model for each engine in the fleet, while recognizing that all engines are of the same type. The methodology is applied to a virtual fleet of engines generated within the Propulsion Diagnostic Methodology Evaluation Strategy (ProDiMES) environment. The set of models is assessed quantitatively through the coefficient of determination and is further used to perform anomaly detection.
- 1 September 2015
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 138 (2) , 021201
Regression-Based Modeling of a Fleet of Gas Turbine Engines for Performance Trending
Module performance analysis is a well-established framework to assess changes in the health condition of the components of the engine gas-path. The primary material of the technique is the so-called vector of residuals, which are built as the difference between actual measurement taken in the gas-path and the values predicted by means of an engine model. Obviously, the quality of the assessment of the engine condition depends strongly on the accuracy of the engine model. The present paper proposes a new approach for data-driven modeling of a fleet of engines of a given type. Such black-box models can be designed by operators, such as airlines and third-party companies. The fleet-wide modeling process is formulated as a regression problem that provides a dedicated model for each engine in the fleet, while recognizing that all engines are of the same type. The methodology is applied to a virtual fleet of engines generated within the Propulsion Diagnostic Methodology Evaluation Strategy (ProDiMES) environment. The set of models is assessed quantitatively through the coefficient of determination and is further used to perform anomaly detection.
- 16 September 2014
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 137 (2) , 022603
Analysis Versus Synthesis for Trending of Gas-Path Measurement Time Series
Gas-path measurements used to assess the health condition of an engine are corrupted by noise. Generally, a data cleaning step occurs before proceeding with fault detection and isolation. Classical linear filters such as the EWMA filter are traditionally used for noise removal. Unfortunately, these low-pass filters distort trend shifts indicative of faults, which increases the detection delay. The present paper investigates two new approaches to nonlinear filtering of time series. On the one hand, the synthesis approach reconstructs the signal as a combination of elementary signals chosen from a predefined library. On the other hand, the analysis approach imposes a constraint on the shape of the signal (e.g., piecewise constant). Both approaches incorporate prior information about the signal in a different way, but they lead to trend filters that are very capable at noise removal while preserving at the same time sharp edges in the signal. This is highlighted through the comparison with a classical linear filter on a batch of synthetic data representative of typical engine fault profiles.
- 16 September 2014
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 137 (2) , 022603
Analysis Versus Synthesis for Trending of Gas-Path Measurement Time Series
Gas-path measurements used to assess the health condition of an engine are corrupted by noise. Generally, a data cleaning step occurs before proceeding with fault detection and isolation. Classical linear filters such as the EWMA filter are traditionally used for noise removal. Unfortunately, these low-pass filters distort trend shifts indicative of faults, which increases the detection delay. The present paper investigates two new approaches to nonlinear filtering of time series. On the one hand, the synthesis approach reconstructs the signal as a combination of elementary signals chosen from a predefined library. On the other hand, the analysis approach imposes a constraint on the shape of the signal (e.g., piecewise constant). Both approaches incorporate prior information about the signal in a different way, but they lead to trend filters that are very capable at noise removal while preserving at the same time sharp edges in the signal. This is highlighted through the comparison with a classical linear filter on a batch of synthetic data representative of typical engine fault profiles.
- 1 September 2011
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 133 (12) , 121602
Constrained Sparse Estimation for Improved Fault Isolation
Least-squares-based methods are very popular in the jet engine community for health monitoring purpose. Their isolation capability can be improved by using a prior knowledge on the health parameters that better matches the expected pattern of the solution i.e., a sparse one as accidental faults impact at most one or two component(s) simultaneously. On the other hand, complimentary information about the feasible values of the health parameters can be derived in the form of constraints. The present contribution investigates the effect of the addition of such constraints on the performance of the sparse estimation tool. Due to its quadratic programming formulation, the constraints are integrated in a straightforward manner. Results obtained on a variety of fault conditions simulated with a commercial turbofan model show that the inclusion of constraints further enhance the isolation capability of the sparse estimator. In particular, the constraints help resolve a confusion issue between high pressure compressor and variable stator vanes faults.
- 1 September 2011
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 133 (12) , 121602
Constrained Sparse Estimation for Improved Fault Isolation
Least-squares-based methods are very popular in the jet engine community for health monitoring purpose. Their isolation capability can be improved by using a prior knowledge on the health parameters that better matches the expected pattern of the solution i.e., a sparse one as accidental faults impact at most one or two component(s) simultaneously. On the other hand, complimentary information about the feasible values of the health parameters can be derived in the form of constraints. The present contribution investigates the effect of the addition of such constraints on the performance of the sparse estimation tool. Due to its quadratic programming formulation, the constraints are integrated in a straightforward manner. Results obtained on a variety of fault conditions simulated with a commercial turbofan model show that the inclusion of constraints further enhance the isolation capability of the sparse estimator. In particular, the constraints help resolve a confusion issue between high pressure compressor and variable stator vanes faults.
- 31 May 2011
- Published by Wiley in Journal of Turbomachinery
- Vol. 134 (1) , 011017
Toward a High Order Throughflow––Investigation of the Nonlinear Harmonic Method Coupled With an Immersed Boundary Method for the Modeling of the Circumferential Stresses
Capturing a level of modeling of the flow inside a multistage turbomachine, such as unsteadiness for example, can be done at different levels of detail, either by capturing all deterministic features of the flow with a pure unsteady method or by settling for an approximated solution at a lower computational cost. The harmonic methods stand in this second category. Among them, the “nonlinear harmonic method” (NLHM) from He and Ning [1998, “Efficient Approach for Analysis of Unsteady Viscous Flows in Turbomachines,” AIAA J., 36, pp. 2005–2012] revealed the most efficient. This method consists of solving the fully nonlinear 3D steady problem and a linearized perturbation system in the frequency domain. As it has been shown by the authors that the circumferential variations exhibit a harmonic behavior, it is proposed here to adapt the NLHM to the throughflow model, where the main nonlinear system would be the common throughflow equations and the auxiliary system would give access to the circumferential stresses. As the numerical local explicit impermeability conditions are unsupported by Fourier series, the adaptation of this technique to the throughflow model relies on a reformulation of the blade effect by a smooth force field as in the “immersed boundary method” from Peskin [2002, “The Immersed Boundary Method,” Acta Numerica, 11, pp. 1–39]. A simple example of an inviscid flow around a cylinder will illustrate the preceding developments, bringing back the mean effect of the circumferential nonuniformities into the meridional flow.
- 31 May 2011
- Published by Wiley in Journal of Turbomachinery
- Vol. 134 (1) , 011017
Toward a High Order Throughflow––Investigation of the Nonlinear Harmonic Method Coupled With an Immersed Boundary Method for the Modeling of the Circumferential Stresses
Capturing a level of modeling of the flow inside a multistage turbomachine, such as unsteadiness for example, can be done at different levels of detail, either by capturing all deterministic features of the flow with a pure unsteady method or by settling for an approximated solution at a lower computational cost. The harmonic methods stand in this second category. Among them, the “nonlinear harmonic method” (NLHM) from He and Ning [1998, “Efficient Approach for Analysis of Unsteady Viscous Flows in Turbomachines,” AIAA J., 36, pp. 2005–2012] revealed the most efficient. This method consists of solving the fully nonlinear 3D steady problem and a linearized perturbation system in the frequency domain. As it has been shown by the authors that the circumferential variations exhibit a harmonic behavior, it is proposed here to adapt the NLHM to the throughflow model, where the main nonlinear system would be the common throughflow equations and the auxiliary system would give access to the circumferential stresses. As the numerical local explicit impermeability conditions are unsupported by Fourier series, the adaptation of this technique to the throughflow model relies on a reformulation of the blade effect by a smooth force field as in the “immersed boundary method” from Peskin [2002, “The Immersed Boundary Method,” Acta Numerica, 11, pp. 1–39]. A simple example of an inviscid flow around a cylinder will illustrate the preceding developments, bringing back the mean effect of the circumferential nonuniformities into the meridional flow.
- 8 April 2011
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 133 (8) , 081604
A Study on Engine Health Monitoring in the Frequency Domain
Most of the techniques developed to date for module performance analysis rely on steady-state measurements from a single operating point to evaluate the level of deterioration of an engine. One of the major difficulties associated with this estimation problem comes from its underdetermined nature. It results from the fact that the number of health parameters exceeds the number of available sensors. Among the panel of remedies to this issue, a few authors have investigated the potential of using data collected during a transient operation of the engine. A major outcome of these studies is an improvement in the assessed health condition. The present study proposes a framework that formalizes this observation for a given class of input signals. The analysis is performed in the frequency domain, following the lines of system identification theory. More specifically, the mean-squared estimation error is shown to drastically decrease when using transient input signals. This study is conducted with an engine model representative of a commercial turbofan.
- 8 April 2011
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 133 (8) , 081604
A Study on Engine Health Monitoring in the Frequency Domain
Most of the techniques developed to date for module performance analysis rely on steady-state measurements from a single operating point to evaluate the level of deterioration of an engine. One of the major difficulties associated with this estimation problem comes from its underdetermined nature. It results from the fact that the number of health parameters exceeds the number of available sensors. Among the panel of remedies to this issue, a few authors have investigated the potential of using data collected during a transient operation of the engine. A major outcome of these studies is an improvement in the assessed health condition. The present study proposes a framework that formalizes this observation for a given class of input signals. The analysis is performed in the frequency domain, following the lines of system identification theory. More specifically, the mean-squared estimation error is shown to drastically decrease when using transient input signals. This study is conducted with an engine model representative of a commercial turbofan.
- Open Access
- 1 January 2011
- Published by European Turbomachinery Society
Post-stall behavior simulations in multistage compressors – part i: steady-state simulations
This contribution presents a reliable CFD tool to simulate stationary and transient behavior for both pre-stall and post-stall operations in multistage low-speed axial compressors. The model is based on a quasi-one-dimensional adapted version of Euler equations discretized at mid-span of the turbomachine: mass, axial momentum, circumferential momentum and energy balances, which are solved by a time-marching, finitevolume method. Source terms have been incorporated in the Euler equations to express the blade-flow interactions, which are estimated by calculating the velocity triangles for each blade row at mid-span. Several loss and deviation models have been implemented and are compared to experimental data in normal mass flow, low mass flow and reversed mass flow regions. Steady numerical results are compared to open literature axial compressor rig data, which provide the detailed geometry information and steady performance in all flow regions.
- 1 January 2011
- Published by European Turbomachinery Society
Open AccessPost-stall behavior simulations in multistage compressors – part i: steady-state simulations
This contribution presents a reliable CFD tool to simulate stationary and transient behavior for both pre-stall and post-stall operations in multistage low-speed axial compressors. The model is based on a quasi-one-dimensional adapted version of Euler equations discretized at mid-span of the turbomachine: mass, axial momentum, circumferential momentum and energy balances, which are solved by a time-marching, finitevolume method. Source terms have been incorporated in the Euler equations to express the blade-flow interactions, which are estimated by calculating the velocity triangles for each blade row at mid-span. Several loss and deviation models have been implemented and are compared to experimental data in normal mass flow, low mass flow and reversed mass flow regions. Steady numerical results are compared to open literature axial compressor rig data, which provide the detailed geometry information and steady performance in all flow regions.
- Open Access
- 1 January 2011
- Published by European Turbomachinery Society
A Quasi-1D model for transonic multistage axial compressors
This contribution presents a quasi-1D numerical tool developed for the simulation of steady-state performance of transonic multistage axial compressors. Although this quasi-1D model offers only a gross simplification of complex 3D phenomena, it only requires simple geometrical inputs and delivers reliable predictions for preliminary design and optimization. This model is based on an adapted version of the Euler equations including source terms representing the interactions between blade rows and fluid. The Euler equations are solved at mid-span by a time-marching, finite-volume method. The source terms are determined by the velocity triangles at inlet and outlet of the blade rows. The loss coefficients and deviation angles are estimated by empirical correlations. Four different transonic compressors have been analysed with this model and numerical results are compared to experimental data.
- 1 January 2011
- Published by European Turbomachinery Society
Open AccessA Quasi-1D model for transonic multistage axial compressors
This contribution presents a quasi-1D numerical tool developed for the simulation of steady-state performance of transonic multistage axial compressors. Although this quasi-1D model offers only a gross simplification of complex 3D phenomena, it only requires simple geometrical inputs and delivers reliable predictions for preliminary design and optimization. This model is based on an adapted version of the Euler equations including source terms representing the interactions between blade rows and fluid. The Euler equations are solved at mid-span by a time-marching, finite-volume method. The source terms are determined by the velocity triangles at inlet and outlet of the blade rows. The loss coefficients and deviation angles are estimated by empirical correlations. Four different transonic compressors have been analysed with this model and numerical results are compared to experimental data.
- Open Access
- 1 January 2011
- Published by European Turbomachinery Society
Post-stall behavior simulations in multistage compressors Part II: transient simulations
This contribution is devoted to a quasi one-dimensional model for the simulation of the dynamic performance of multistage axial compressors during post-stalls. An adapted version of the 1D Euler equations with additional source terms is discretized with a finite volume method and by a fourth-order Runge-Kutta time-marching scheme. The equations are discretized at mid-span both inside the blade rows and the non-bladed regions. Empirical correlations are included in this model to replace the compressor steady characteristics. In this way the model can be applied to simulate the transient performance of a compressor, on the sole basis of its geometrical input. It provides the possibility to explore post-stall transients, including stall and surge, before the manufacturing of the compressor. The numerical simulations are validated against the three-stage compressor of Gamache. A parametric study is also carried out to analyze the shape of surge circles and the frequency of surge oscillations.
- 1 January 2011
- Published by European Turbomachinery Society
Open AccessPost-stall behavior simulations in multistage compressors Part II: transient simulations
This contribution is devoted to a quasi one-dimensional model for the simulation of the dynamic performance of multistage axial compressors during post-stalls. An adapted version of the 1D Euler equations with additional source terms is discretized with a finite volume method and by a fourth-order Runge-Kutta time-marching scheme. The equations are discretized at mid-span both inside the blade rows and the non-bladed regions. Empirical correlations are included in this model to replace the compressor steady characteristics. In this way the model can be applied to simulate the transient performance of a compressor, on the sole basis of its geometrical input. It provides the possibility to explore post-stall transients, including stall and surge, before the manufacturing of the compressor. The numerical simulations are validated against the three-stage compressor of Gamache. A parametric study is also carried out to analyze the shape of surge circles and the frequency of surge oscillations.
- 4 November 2009
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 132 (2) , 021601
A Sparse Estimation Approach to Fault Isolation
Least-squares-based methods are very popular in the jet engine community for health monitoring purposes. In most practical situations, the number of health parameters exceeds the number of measurements, making the estimation problem underdetermined. To address this issue, regularization adds a penalty term on the deviations of the health parameters. Generally, this term imposes a quadratic penalization on these deviations. A side effect of this technique is a relatively poor isolation capability. The latter feature can be improved by recognizing that abrupt faults impact at most one or two component(s) simultaneously. This translates mathematically into the search for a sparse solution. The present contribution reports the development of a fault isolation tool favoring sparse solutions. It is very efficiently implemented in the form of a quadratic program. As a validation procedure, the resulting algorithm is applied to a variety of fault conditions simulated with a generic commercial turbofan model.
- 4 November 2009
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 132 (2) , 021601
A Sparse Estimation Approach to Fault Isolation
Least-squares-based methods are very popular in the jet engine community for health monitoring purposes. In most practical situations, the number of health parameters exceeds the number of measurements, making the estimation problem underdetermined. To address this issue, regularization adds a penalty term on the deviations of the health parameters. Generally, this term imposes a quadratic penalization on these deviations. A side effect of this technique is a relatively poor isolation capability. The latter feature can be improved by recognizing that abrupt faults impact at most one or two component(s) simultaneously. This translates mathematically into the search for a sparse solution. The present contribution reports the development of a fault isolation tool favoring sparse solutions. It is very efficiently implemented in the form of a quadratic program. As a validation procedure, the resulting algorithm is applied to a variety of fault conditions simulated with a generic commercial turbofan model.
- 20 April 2009
- Published by Wiley in Journal of Turbomachinery
- Vol. 131 (3) , 031019
On the Role of the Deterministic and Circumferential Stresses in Throughflow Calculations
This paper presents a throughflow analysis tool developed in the context of the average-passage flow model elaborated by Adamczyk. The Adamczyk’s flow model describes the 3D time-averaged flow field within a blade row passage. The set of equations that governs this flow field is obtained by performing a Reynolds averaging, a time averaging, and a passage-to-passage averaging on the Navier–Stokes equations. The throughflow level of approximation is obtained by performing an additional circumferential averaging on the 3D average-passage flow. The resulting set of equations is similar to the 2D axisymmetric Navier–Stokes equations, but additional terms resulting from the averages show up: blade forces, blade blockage factor, Reynolds stresses, deterministic stresses, passage-to-passage stresses, and circumferential stresses. This set of equations represents the ultimate throughflow model provided that all stresses and blade forces can be modeled. The relative importance of these additional terms is studied in the present contribution. The stresses and the blade forces are determined from 3D steady and unsteady databases (a low-speed compressor stage and a transonic turbine stage) and incorporated in a throughflow model based on the axisymmetric Navier–Stokes equations. A good agreement between the throughflow solution and the averaged 3D results is obtained. These results are also compared to those obtained with a more “classical” throughflow approach based on a Navier–Stokes formulation for the endwall losses, correlations for profile losses, and a simple radial mixing model assuming turbulent diffusion.
- 20 April 2009
- Published by Wiley in Journal of Turbomachinery
- Vol. 131 (3) , 031019
On the Role of the Deterministic and Circumferential Stresses in Throughflow Calculations
This paper presents a throughflow analysis tool developed in the context of the average-passage flow model elaborated by Adamczyk. The Adamczyk’s flow model describes the 3D time-averaged flow field within a blade row passage. The set of equations that governs this flow field is obtained by performing a Reynolds averaging, a time averaging, and a passage-to-passage averaging on the Navier–Stokes equations. The throughflow level of approximation is obtained by performing an additional circumferential averaging on the 3D average-passage flow. The resulting set of equations is similar to the 2D axisymmetric Navier–Stokes equations, but additional terms resulting from the averages show up: blade forces, blade blockage factor, Reynolds stresses, deterministic stresses, passage-to-passage stresses, and circumferential stresses. This set of equations represents the ultimate throughflow model provided that all stresses and blade forces can be modeled. The relative importance of these additional terms is studied in the present contribution. The stresses and the blade forces are determined from 3D steady and unsteady databases (a low-speed compressor stage and a transonic turbine stage) and incorporated in a throughflow model based on the axisymmetric Navier–Stokes equations. A good agreement between the throughflow solution and the averaged 3D results is obtained. These results are also compared to those obtained with a more “classical” throughflow approach based on a Navier–Stokes formulation for the endwall losses, correlations for profile losses, and a simple radial mixing model assuming turbulent diffusion.