K. B. Povarova
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
K. B. Povarova has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
A. A. Drozdov
Baikov Institute of Metallurgy and Materials Science, Russian Academy of Sciences, Moscow, Russia
31 shared publicationsA. E. Morozov
Baikov Institute of Metallurgy and Materials Science, Russian Academy of Sciences, Moscow, Russia
26 shared publicationsO. A. Bazyleva
FGUP GNTs RF VIAM, Moscow, Russia
15 shared publicationsA. V. Antonova
Baikov Institute of Metallurgy and Materials Science, Russian Academy of Sciences, Moscow, Russia
12 shared publicationsN. K. Kazanskaya
Russian Academy of Sciences
9 shared publicationsM. A. Bulakhtina
Baikov Institute of Metallurgy and Materials Science, Russian Academy of Sciences, Moscow, Russia
7 shared publications
Latest Publications
- 1 July 2021
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2021 (7) , 842-855
Changes in the Structural-Phase State and Mechanical Properties of Ni3Al–Ni–NiAl Cast Alloys Containing Chromium, Molybdenum, Tungsten, Rhenium, and Cobalt after Heat Treatment
The influence of the temperature–time parameters (temperature from 1000 to 1300°C, time from 1 to 500 h) of heat treatment (HT) of 〈001〉 and 〈111〉 single crystals of boron-free heterophase γ'-Ni3Al + γ‑Ni intermetallic (IM) alloys of the Ni–Al–Cr–Mo–W–Ti(Zr)–La system (VKNA-1V) and such alloys with cobalt and rhenium (VKNA-25) on their structure, fracture, and short-term and long-term strength is studied. The introduction of cobalt and rhenium or an increase in the cooling rate of the 〈001〉 single crystals in the range 30–300°C/min is found to decrease the sizes of the structural components of all levels. In addition, the rule derived for two- and three-component nickel-based alloys is shown to be valid for γ'-Ni3Al-based IM alloys: if an introduced alloying element (AE) increases the melting point Tm of the base metal (nickel), the AE distribution coefficient is kd > 1 and the AE enriches dendrite arms; if AE decreases Tm of nickel, we have kd < 1 and the AE enriches the interdendritic space. The AE dendritic microsegregation coefficients kd weakly depend on the cooling rate during solidification, and their values decrease in the following row: Re, W, Co, Mo, Al, and Ti. An increase in the time of low-temperature HT (T < Tsolvus) or an increase in the HT temperature to Tsolvus ≤ T ≤ Tsolidus leads to the “homogenization” of heterophase γ' + γ IM alloys. The dendritic microsegregation coefficients of all AEs except for Re approach unity, and interdendritic nonequilibrium \(\gamma _{{{\text{pr}}}}^{'}\) and γ' + β precipitates disappear. A homogeneous γ' + γ structure, which is characteristic of IM dendrites (γ'-phase regions of irregular shape separated by continuous or discontinuous γ-phase layers), forms. It differs from the structure of nickel superalloys. This type of homogenization decreases the durability as compared to the as-cast material, which retains the maximum microsegregation heterogeneity after short-term HT in order to relieve casting stresses.- 1 July 2021
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2021 (7) , 842-855
Changes in the Structural-Phase State and Mechanical Properties of Ni3Al–Ni–NiAl Cast Alloys Containing Chromium, Molybdenum, Tungsten, Rhenium, and Cobalt after Heat Treatment
The influence of the temperature–time parameters (temperature from 1000 to 1300°C, time from 1 to 500 h) of heat treatment (HT) of 〈001〉 and 〈111〉 single crystals of boron-free heterophase γ'-Ni3Al + γ‑Ni intermetallic (IM) alloys of the Ni–Al–Cr–Mo–W–Ti(Zr)–La system (VKNA-1V) and such alloys with cobalt and rhenium (VKNA-25) on their structure, fracture, and short-term and long-term strength is studied. The introduction of cobalt and rhenium or an increase in the cooling rate of the 〈001〉 single crystals in the range 30–300°C/min is found to decrease the sizes of the structural components of all levels. In addition, the rule derived for two- and three-component nickel-based alloys is shown to be valid for γ'-Ni3Al-based IM alloys: if an introduced alloying element (AE) increases the melting point Tm of the base metal (nickel), the AE distribution coefficient is kd > 1 and the AE enriches dendrite arms; if AE decreases Tm of nickel, we have kd < 1 and the AE enriches the interdendritic space. The AE dendritic microsegregation coefficients kd weakly depend on the cooling rate during solidification, and their values decrease in the following row: Re, W, Co, Mo, Al, and Ti. An increase in the time of low-temperature HT (T < Tsolvus) or an increase in the HT temperature to Tsolvus ≤ T ≤ Tsolidus leads to the “homogenization” of heterophase γ' + γ IM alloys. The dendritic microsegregation coefficients of all AEs except for Re approach unity, and interdendritic nonequilibrium \(\gamma _{{{\text{pr}}}}^{'}\) and γ' + β precipitates disappear. A homogeneous γ' + γ structure, which is characteristic of IM dendrites (γ'-phase regions of irregular shape separated by continuous or discontinuous γ-phase layers), forms. It differs from the structure of nickel superalloys. This type of homogenization decreases the durability as compared to the as-cast material, which retains the maximum microsegregation heterogeneity after short-term HT in order to relieve casting stresses.- 7 May 2020
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2020 (5) , 540-548
Solidification and the Structure-Phase State of Ni3Al–Ni–NiAl Alloys with Chromium, Molybdenum, Tungsten, Rhenium, and Cobalt
The ternary Ni–Al–AE phase diagrams, where AEs are the main alloying elements of high-temperature cast (γ' + γ) γ'-Ni3Al-based alloys, are analyzed. Principal differences between the solidification schemes in the vicinity of the γ'-Ni3Al and β-NiAl phases and the differences in the characters of the influence of the main AEs at their contents to 10 at % on the phase composition and the structure of multicomponent γ'-Ni3Al-based VKNA-1V, VKNA-25, VKNA-4U, and IM730 alloys are detcted. The structural base of all the alloys are (γ' + γ) dendrites. In the first-type cobalt-free VKNA1V alloys, as well as in IC221M, IC218, IC438, and IC6SX alloys, coarse single-phase γ'-Ni3Al precipitates, which are the degenerate eutectic L\( \rightleftarrows \) (γ' + γ) + γ', form in the interdendritic space. In the second-type cobalt-containing alloys at the same (~17 at %) aluminum content (VKNA-4U, VKNA-25) or in the chromium-containing cobalt-free alloys with an increased (~21 at %) aluminum content (IM730), the following two-phase precipitates form: the nonequilibrium β-NiAl phase, which represents the degenerate L\( \rightleftarrows \) (γ' + β) + β eutectic, forms inside γ'-Ni3Al. The following solid-phase transformations are found to develop intensely in the second-type alloys on heating in the temperature range 1200–1300°C: the dissolution of the β-phase precipitates in the primary γ'-Ni3Al precipitates, the dissolution or a weakening of the interdendritic γ'-phase precipitates, and a change in the morphology and orientations of the γ-phase precipitates in dendrites and the interdendritic space.- 7 May 2020
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2020 (5) , 540-548
Solidification and the Structure-Phase State of Ni3Al–Ni–NiAl Alloys with Chromium, Molybdenum, Tungsten, Rhenium, and Cobalt
The ternary Ni–Al–AE phase diagrams, where AEs are the main alloying elements of high-temperature cast (γ' + γ) γ'-Ni3Al-based alloys, are analyzed. Principal differences between the solidification schemes in the vicinity of the γ'-Ni3Al and β-NiAl phases and the differences in the characters of the influence of the main AEs at their contents to 10 at % on the phase composition and the structure of multicomponent γ'-Ni3Al-based VKNA-1V, VKNA-25, VKNA-4U, and IM730 alloys are detcted. The structural base of all the alloys are (γ' + γ) dendrites. In the first-type cobalt-free VKNA1V alloys, as well as in IC221M, IC218, IC438, and IC6SX alloys, coarse single-phase γ'-Ni3Al precipitates, which are the degenerate eutectic L\( \rightleftarrows \) (γ' + γ) + γ', form in the interdendritic space. In the second-type cobalt-containing alloys at the same (~17 at %) aluminum content (VKNA-4U, VKNA-25) or in the chromium-containing cobalt-free alloys with an increased (~21 at %) aluminum content (IM730), the following two-phase precipitates form: the nonequilibrium β-NiAl phase, which represents the degenerate L\( \rightleftarrows \) (γ' + β) + β eutectic, forms inside γ'-Ni3Al. The following solid-phase transformations are found to develop intensely in the second-type alloys on heating in the temperature range 1200–1300°C: the dissolution of the β-phase precipitates in the primary γ'-Ni3Al precipitates, the dissolution or a weakening of the interdendritic γ'-phase precipitates, and a change in the morphology and orientations of the γ-phase precipitates in dendrites and the interdendritic space.- 1 January 2019
- Published by Springer Nature in Metal Science and Heat Treatment
- Vol. 60 (9-10) , 594-601
Effect of Heat Treatment on Dendritic Segregation and High-Temperature Strength of Single Crystals of Ni3Al-Base Rhenium-Alloyed Intermetallic Alloys
- 1 January 2019
- Published by Springer Nature in Metal Science and Heat Treatment
- Vol. 60 (9-10) , 594-601
Effect of Heat Treatment on Dendritic Segregation and High-Temperature Strength of Single Crystals of Ni3Al-Base Rhenium-Alloyed Intermetallic Alloys
- 1 July 2018
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2018 (7) , 645-650
Influence of the Cobalt Concentration and Chromium Alloying on the Structure of (β-NiAl + γ'-Ni3Al + γ-Ni) Ni–Al–Co Superalloys
The influence of cobalt (5 and 16 at %) and chromium (4.25 at %) on the structure of a (β-NiAl + γ'-Ni3Al + γ-Ni) alloy with 27 at % Al of the Ni–Al–Co system, which is chosen as the basis...
- 1 July 2018
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2018 (7) , 645-650
Influence of the Cobalt Concentration and Chromium Alloying on the Structure of (β-NiAl + γ'-Ni3Al + γ-Ni) Ni–Al–Co Superalloys
The influence of cobalt (5 and 16 at %) and chromium (4.25 at %) on the structure of a (β-NiAl + γ'-Ni3Al + γ-Ni) alloy with 27 at % Al of the Ni–Al–Co system, which is chosen as the basis...
- 1 January 2018
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2018 (1) , 42-50
Formation of Gradient Structures in the Zone of Joining a Deformable Nickel Alloy and a Single-Crystal Intermetallic Alloy during Thermodiffusion Pressure Welding and Subsequent Heat Treatment
The possibility of formation of a high-quality solid-phase joint of an Ni3Al-based single-crystal intermetallic VKNA-25 blade alloy with a high-temperature deformable EP975 disk alloy by pressure...
- 1 January 2018
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2018 (1) , 42-50
Formation of Gradient Structures in the Zone of Joining a Deformable Nickel Alloy and a Single-Crystal Intermetallic Alloy during Thermodiffusion Pressure Welding and Subsequent Heat Treatment
The possibility of formation of a high-quality solid-phase joint of an Ni3Al-based single-crystal intermetallic VKNA-25 blade alloy with a high-temperature deformable EP975 disk alloy by pressure...
- 1 September 2017
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2017 (9) , 706-710
Structural heat-resistant β-NiAl + γ′-Ni3Al alloys of the Ni–Al–Co system: II. Oxidation
The heat resistance of the β + γ′ alloys with 28–29 at % Al, 10 at % Co, and 0.25–0.4 at % Re in air at 1300°C is studied. The structures of the scale and the subscale layers that form during oxidatio
- 1 September 2017
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2017 (9) , 706-710
Structural heat-resistant β-NiAl + γ′-Ni3Al alloys of the Ni–Al–Co system: II. Oxidation
The heat resistance of the β + γ′ alloys with 28–29 at % Al, 10 at % Co, and 0.25–0.4 at % Re in air at 1300°C is studied. The structures of the scale and the subscale layers that form during oxidatio
- 1 September 2017
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2017 (9) , 696-705
Structural heat-resistant β-NiAl + γ′-Ni3Al alloys of the Ni–Al–Co system: I. Solidification and structure
When analyzing the ternary Ni–Al–M phase diagrams, where M is a group VI–VIII transition metal, we chose the Ni–Al–Co system, where the γ′ and γ phases are in equilibrium with the β phase, as a base f
- 1 September 2017
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2017 (9) , 696-705
Structural heat-resistant β-NiAl + γ′-Ni3Al alloys of the Ni–Al–Co system: I. Solidification and structure
When analyzing the ternary Ni–Al–M phase diagrams, where M is a group VI–VIII transition metal, we chose the Ni–Al–Co system, where the γ′ and γ phases are in equilibrium with the β phase, as a base f
- 1 January 2015
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2015 (1) , 43-50
Effect of directional solidification on the structure and properties of Ni3Al-based alloy single crystals alloyed with Cr, Mo, W, Ti, Co, Re, and REM
The effect of the solidification rate ( R = 2, 5, 10, 20 mm/min) at the same solidification gradient ( G= 150°C/cm) on the structural parameters of single-crystal blade workpieces made of an alloy...
- 1 January 2015
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2015 (1) , 43-50
Effect of directional solidification on the structure and properties of Ni3Al-based alloy single crystals alloyed with Cr, Mo, W, Ti, Co, Re, and REM
The effect of the solidification rate ( R = 2, 5, 10, 20 mm/min) at the same solidification gradient ( G= 150°C/cm) on the structural parameters of single-crystal blade workpieces made of an alloy...