GRGamal Refai-Ahmed

Gamal Refai-Ahmed

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Gamal Refai-Ahmed has a total of 10 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Multi-Objective Optimization to Improve Both Thermal and Device Performance of a Nonuniformly Powered Micro-Architecture

    by Saket Karajgikar, Dereje Agonafer, Kanad Ghose, Bahgat Sammakia, Cristina Amon, Gamal Refai-Ahmed

    Integration of different functional components such as level two (L2) cache memory, high-speed I/O interfaces, and memory controller has enhanced microprocessor performance. In this architecture, certain functional units on the microprocessor dissipate a significant fraction of the total power while other functional units dissipate little or no power. This highly nonuniform power distribution results in a large temperature gradient with localized hot spots that may have detrimental effects on computer performance, product reliability, and yield. Moving the functional units may reduce the junction temperature but can affect performance by a factor as much as 30%. In this paper, a multi-objective optimization is performed to minimize the junction temperature without significantly altering the computer performance. The analysis was performed for 90 nm Pentium IV Northwood architecture operating at 3 GHz clock speed. Each functional unit on the die has a specific role, so functional units with similar roles were grouped together. Thus, the actual Pentium IV die was divided into four groups (front end, execution cores, bus and L2, and out-of-order engine). Repositioning constraints were determined using circuit delay models of major functional units in a micro-architectural simulator. Thus, depending on the scenario, relocating functional units can result in virtually no performance loss (less than 2% is assumed to be minimal and is reported as 0%) to as much as 30% performance loss. From the results, the minimum and the maximum temperatures were 56.6°C and 62.2°C. This ΔT corresponds to thermal design power of 60.2 W. For microprocessors with higher thermal design power (115 W) and operating at higher clock speed, higher ΔT can be realized. Based on this paper’s analysis, the optimized scenario resulted in a junction temperature of 56.6°C at the cost of a 14% performance loss.


  • Multi-Objective Optimization of Graphite Heat Spreader for Portable Systems Applications

    by Nikhil Lakhkar, Arijit Banerjee, Gamal Refai-Ahmed, Dereje Agonafer

    The advancement made in portable electronic systems has primarily been due to miniaturization of electronic devices. This results in an increase in power density that leads to higher temperatures and formation of hot spots. There is a temperature specification of system surfaces for human comfort (such as the surface close to a keyboard on laptops). The challenge of cooling portable devices is that there is not enough room to accommodate heat sinks. It is therefore important to have heat spreaders that can transfer the heat from critical devices to regions where cooling is available. Traditionally, copper has been the best heat spreader due to its high thermal conductivity. However, copper has a relatively high density and correspondingly high weight. Graphite is a suitable alternative. Recent advances in graphite technology have resulted in fairly high conductivity in the planar directions. In spite of these advances, the cost of graphite is an issue. In this paper, a multi-objective optimization is utilized that considers weight of the graphite heat spreader as objective functions. The data is then compared to published data that utilizes graphite in a laptop.


  • Development of a Numerical Model for Non-Uniformly Powered Die to Improve Both Thermal and Device Clock Performance

    by Saket Karajgikar, Dereje Agonafer, Kanad Ghose, Bahgat Sammakia, Cristina Amon, Gamal Refai-Ahmed

    Integration of different functional components such as level two (L2) cache memory, high-speed I/O interfaces, memory controller, etc. has enhanced microprocessor performance. In this architecture, certain functional units on the microprocessor dissipate a significant fraction of the total power while other functional blocks dissipate little or no power. This highly non-uniform power distribution results in a large temperature gradient with localized hot spots that may have detrimental effect on computer performance and product reliability as well as yield. Moving the functional blocks may reduce the junction temperature but can also affect the performance by a factor as high as 35%. In this paper, multi-objective optimization is performed to minimize the junction temperature without significantly altering the computer performance. From the results, the minimum and the maximum temperature was 82.4°C and 94.5°C with a corresponding penalty on the performance of 35% and 0% respectively. The optimized location of the functional blocks resulted in a temperature of 83.2°C for a performance loss of 5%.


  • Effect of Heat Sink Assembly on Mechanical Reliability of a Wire Bonded Plastic Ball Grid Array Package

    by Aalok Trivedi, Abhijit Kaisare, Dereje Agonafer, Gamal Refai-Ahmed

    Since the advent of the transistor and integrated circuit, the performance of electronic equipment has increased significantly while footprint of systems at all levels continues to decrease. Recently, the number of transistors on a high end microprocessor has exceeded a billion. All of the above has necessitated considerable improvement in cooling technology and associated reliability. Heat sinks play an important role in cooling technology by providing an increased surface area to dissipate heat. While there has been a great deal of work related to the thermal performance of heat sinks, there has not been a corresponding effort in studying the mechanical related reliability issues of the heat sinks. Previous work has been done to study the effect of adhesively bonded heat sink on the mechanical reliability of a two-layer wire bonded plastic ball grid array (WB-PBGA) package. Stresses induced in the package have been computed for a wide range of values of the adhesive mechanical properties and Young’s modulus. Variation of interfacial peel and shear stresses at the interface between the mold compound and the adhesive and between the adhesive and the heat sink have been qualitatively assessed for propensity of interfacial de-lamination along these two interfaces. In this paper a stress analysis of described package is carried out to study the effect of heat sink assembly on the mechanical reliability of the package. A three dimensional finite element model of WB-PBGA package and Printed wiring board (PWB) is solved numerically to predict the stresses induced and assess their impact on the mechanical integrity of the die and package due to the heat sink assembly. Die and C4 interconnect stresses are examined to evaluate package reliability. Stresses induced within the die and C4 interconnect are examined for different heat sink materials and variation of force developed by heat sink attachments such as clip and screw type has been examined. Finally recommendations will be made regarding choice of heat sink material and clipping force for overall heat sink assembly design. The modeling utilizes a solid model for geometry creation and a finite element commercial program for simulation.