HSHarold Schock

Harold Schock

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Harold Schock has a total of 57 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Optimal Combustion Phasing Modeling and Control of a Turbulent Jet Ignition Engine

    by Ruitao Song, Ravi Teja Vedula, Guoming G. Zhu, Harold Schock

    Combustion phasing control is very important for internal combustion engines to achieve high thermal efficiency with low engine-out emissions. Traditional open-loop map-based control becomes less favorable in terms of calibration effort, robustness to engine aging, and especially control accuracy for turbulent jet ignition (TJI) engines due to the increased number of control variables over conventional spark-ignition engines. In this paper, a model-based feedforward controller is developed for a TJI engine. A feedback controller is designed based on the linear quadratic tracking control with output covariance constraint. Since the TJI main-chamber combustion is influenced by the pre-chamber one, the proposed controller optimizes the control variables in both combustion chambers. The proposed feedforward and feedback controller reduces standard deviation of combustion phase by more than 22% over a group of baseline controllers through a series of dynamometer engine tests.


  • Combustion Model for a Homogeneous Turbocharged Gasoline Direct-Injection Engine

    by Sedigheh Tolou, Ravi Teja Vedula, Harold Schock, Guoming Zhu, Yong Sun, Adam Kotrba

    Homogeneous charge is a preferred operation mode of gasoline direct-injection (GDI) engines. However, a limited amount of work exists in the literature for combustion models of this mode of engine operation. Current work describes a model developed to study combustion in a homogeneous charge GDI engine. The model was validated using experimental data from a 1.6 L Ford EcoBoost® engine, tested at the U.S. EPA. The combustion heat release was approximated using a double-Wiebe function, to account for the rapid initial premixed combustion followed by a gradual diffusion-like state of combustion, as observed in this GDI engine. Variables of Wiebe correlations were adjusted into a semipredictive combustion model. The effectiveness of semipredictive combustion model was tested in prediction of in-cylinder pressures. The root-mean-square (RMS) errors between experiments and numerical results were within 2.5% of in-cylinder peak pressures during combustion. The semipredictive combustion model was further studied to develop a predictive combustion model. The performance of predictive combustion model was examined by regenerating the experimental cumulative heat release. The heat release analysis developed for the GDI engine was further applied to a dual mode, turbulent jet ignition (DM-TJI) engine. DM-TJI is a distributed combustion technology with the potential to provide diesel-like efficiencies and minimal engine-out emissions for spark-ignition engines. The DM-TJI engine was observed to offer a faster burn rate and lower in-cylinder heat transfer compared to the GDI engine.


  • Model-Based Control for Mode Transition Between Spark Ignition and HCCI Combustion

    by Shupeng Zhang, Ruitao Song, Guoming G. Zhu, Harold Schock

    While the homogeneous charge compression ignition (HCCI) combustion has its advantages of high thermal efficiency with low emissions, its operational range is limited in both engine speed and load. To utilize the advantage of the HCCI combustion, an HCCI capable spark ignition (SI) engine is required. One of the key challenges of developing such an engine is to achieve smooth mode transition between SI and HCCI combustion, where the in-cylinder thermal and charge mixture properties are quite different due to the distinct combustion characteristics. In this paper, a control strategy for smooth mode transition between SI and HCCI combustion is developed and experimentally validated for an HCCI capable SI engine equipped with electrical variable valve timing (EVVT) systems, dual-lift valves, and electronic throttle control (ETC) system. During the mode transition, the intake manifold air pressure is controlled by tracking the desired throttle position updated cycle-by-cycle; and an iterative learning fuel mass controller, combined with sensitivity-based compensation, is used to manage the engine torque in terms of net mean effective pressure (NMEP) at the desired level for smooth mode transition. Note that the NMEP is directly correlated to the engine output torque. Experiment results show that the developed controller is able to achieve smooth combustion mode transition, where the NMEP fluctuation is kept below 3.8% during the mode transition.


  • Development of a Circular Thermoelectric Skutterudite Couple Using Compression Technology

    by Nariman Mansouri, Edward J. Timm, Harold J. Schock, Dipankar Sahoo, Adam Kotrba

    Approximately, 55% of the energy produced from conventional vehicle resources is lost due to heat losses. An efficient waste heat recovery process will lead to improved fuel efficiency and greenhouse gas emissions. Thermoelectric generators (TEGs) are heat recovery devices that are being widely studied by a range of energy-intensive industries. Efficient solid-state thermoelectric devices are good candidates to reduce fuel consumption in an automobile. Thermoelectric materials have had limited automotive applications due to the automotive waste heat recovery temperature range, the rarity and toxicity of some materials, and the limited ability to mass manufacture thermoelectric devices from expensive TE materials. However, skutterudite is one class of material that has demonstrated significant promise in the transportation waste heat recovery temperature domain. Durability and reliability of the TEGs are the most significant concerns in the product development process. Cracking of the materials at hot-side interface is found to be a major failure mechanism of TEGs under thermal loading. Cracking affects not only the structural integrity but also the energy conversion and overall performance of the system. In this paper, cracking of thermoelectric material as observed in performance testing is analyzed using numerical simulations and analytic experiments. This paper shows, with the help of finite element analysis (FEA), the detailed distribution of stress, strain, and temperature is obtained for each design. Finite element (FE)-based simulations show the tensile stresses as the primary factor causing radial and circumferential cracks in the skutterudite. For a TEG design, loading conditions and closed-form analytical solutions of stress/strain distributions are derived. Scenarios with minimum tensile stresses are sought. These approaches yield the minimum of stress/strain fields which produce cracks. Finally, based on these analyses and computational fluid dynamics (CFD) studies, strategies in tensile stress reduction and failure prevention are proposed.


  • Three-Dimensional Piston Ring–Cylinder Bore Contact Modeling

    by Chao Cheng, Ali Kharazmi, Harold Schock, Richard Wineland, Larry Brombolich

    Increasing durability, preventing knocking combustion, improving fuel efficiency, and reducing pollutant emission characterize the needs for modern internal combustion engine design. These factors are highly influenced by the power cylinder system design. In particular, the piston ring to cylinder bore contact force distribution around the circumference of the piston rings must be optimized under all running conditions. To accomplish this, the ring manufacturers make the ring curvature nonconstant along the circumference. Most existing analytical tools are not able to simulate the variation along the ring circumference. In order to improve the understanding of this contact distribution and provide a high-fidelity ring design tool, a three-dimensional finite element piston ring model was developed to accomplish this variation. The modeling procedure and results are presented in this work. Experiments using a commercially available ring with negative ovality were conducted to validate the model. The ring free-shape profile and the ring cross section geometries were used as inputs to the model. Typical piston ring groove and cylinder wall temperatures were also model inputs to characterize thermal influences on the ring/bore interface forces. The ring/bore conformability was analyzed as a function of the ring radial displacements, cylinder bore constraint forces and thermal load changes to the ring. The model output showed radially separation gaps between the ring front face and the bore. This analysis provides an insight to evaluate the piston ring design. Together with an optimizer, the model can be used as a ring design tool to predict the ring free shape with a specified constraint force distribution pattern. Examples are given to demonstrate the capabilities of this numerical analytical tool. In addition, the 3D ring model can be used to improve the accuracy of existing lubrication, friction, and wear analysis tools and therefore improve the entire internal combustion engine power cylinder system design.


  • The Dynamics of Second Ring Flutter and Collapse in Modern Diesel Engines

    by Chao Cheng, Harold Schock, Dan Richardson

    Second ring fluttering and radial ring collapse are recognized as having significant influences on engine blowby and oil consumption. As the gas flow is coupled with the piston ring motion, understanding the ring dynamics is important for understanding not only the engine blowby mechanism, but also oil consumption mechanisms and how to control them. Only second ring flutter and collapse that occurs around the top dead center (TDC) firing conditions is examined in this paper based on a modern heavy-duty diesel engine. However, the principles described are equally applicable to all engines. First, the authors describe the fundamental mechanisms of how second ring fluttering and radial ring collapse occur. This is described by examining the forces that are acting on the second ring. Then, two cases are shown. One case shows second ring flutter and the other case shows stable second ring motion. The reasons for these two different cases are explained, including the effect of static twist and the end gaps of the rings. A sensitivity study was performed to evaluate the effect of changing the top and second ring end gaps on ring lift. It was shown how the gaps could affect the second ring flutter and ring collapse. It is concluded that the second ring will be more likely to flutter or collapse if it has a negative static twist, if the second ring end gap is large, and/or if the top ring end gap is small. If the second ring does not flutter, it may still be possible to design the ring pack such that there is not any reverse blowby. However, this must be carefully studied and controlled or the second land pressures will be too high, resulting in reverse blowby and/or top ring lifting.


  • Piston Ring and Groove Side Wear Analysis for Diesel Engines

    by Mulyanto Poort, Chao Cheng, Dan Richardson, Harold Schock

    Piston ring wear is a major factor determining a diesel engine's life. A ring is subjected to wear between its front face and the cylinder wall as well as at the interfaces between the ring and groove top and bottom flanks. In many modern engines, ring and groove wear are becoming more of a limiting factor for ring durability than face wear. The focus of this paper is on ring to groove side wear only. In this paper, two fundamental mechanisms for ring/groove side wear are identified: (1) wear due to piston secondary motion and (2) wear due to ring twist. The time in the cycle where each of these mechanisms results in maximum wear is shown. Then, the effect of ring static twist and the resulting effect on the pressure distribution around the ring are studied. The pressure distribution affects the force acting on the ring that causes the ring/groove side wear. It is also shown that the pressure distribution and the resultant wear can be influenced by the land diameter below the piston ring. Progressive wear is also studied, showing a good correlation between predicted wear and measured wear on both ring sides and groove sides. It is noted that as the corner of the ring/groove wears, the ultimate wear of the ring side can accelerate by a phenomenon named pressure infiltration. Pressure infiltration occurs because the bottom side of the ring groove wears exposing more of bottom side of the ring to lower pressure force. This ultimately causes a higher difference between the high pressure above the ring and the low pressure below the ring. As a result, the net force acting on the ring increases and wear increases. In addition to the study of the first ring, the second ring wear was studied. A comparison was made between the top ring and second ring groove side wear (RGSW) predictions. Also, the effect of the second ring static twist on both top and second ring/groove side wear is described in detail.


  • Flex Fuel Optimized SI and HCCI Engine

    by Guoming Zhu, Harold Schock, Xiaojian Yang, Andrew Huisjen, Tom Stuecken, Kevin Moran, Ren Zhen, Shupeng Zhang, John Opra, Ron Reese

    The central objective of the proposed work is to demonstrate an HCCI (homogeneous charge compression ignition) capable SI (spark ignited) engine that is capable of fast and smooth mode transition between SI and HCCI combustion modes. The model-based control technique was used to develop and validate the proposed control strategy for the fast and smooth combustion mode transition based upon the developed control-oriented engine; and an HCCI capable SI engine was designed and constructed using production ready two-step valve-train with electrical variable valve timing actuating system. Finally, smooth combustion mode transition was demonstrated on a metal engine within eight engine cycles. The Chrysler turbocharged 2.0L I4 direct injection engine was selected as the base engine for the project and the engine was modified to fit the two-step valve with electrical variable valve timing actuating system. To develop the model-based control strategy for stable HCCI combustion and smooth combustion mode transition between SI and HCCI combustion, a control-oriented real-time engine model was developed and implemented into the MSU HIL (hardware-in-the-loop) simulation environment. The developed model was used to study the engine actuating system requirement for the smooth and fast combustion mode transition and to develop the proposed mode transition control strategy.more » Finally, a single cylinder optical engine was designed and fabricated for studying the HCCI combustion characteristics. Optical engine combustion tests were conducted in both SI and HCCI combustion modes and the test results were used to calibrate the developed control-oriented engine model. Intensive GT-Power simulations were conducted to determine the optimal valve lift (high and low) and the cam phasing range. Delphi was selected to be the supplier for the two-step valve-train and Denso to be the electrical variable valve timing system supplier. A test bench was constructed to develop control strategies for the electrical variable valve timing (VVT) actuating system and satisfactory electrical VVT responses were obtained. Target engine control system was designed and fabricated at MSU for both single-cylinder optical and multi-cylinder metal engines. Finally, the developed control-oriented engine model was successfully implemented into the HIL simulation environment. The Chrysler 2.0L I4 DI engine was modified to fit the two-step vale with electrical variable valve timing actuating system. A used prototype engine was used as the base engine and the cylinder head was modified for the two-step valve with electrical VVT actuating system. Engine validation tests indicated that cylinder #3 has very high blow-by and it cannot be reduced with new pistons and rings. Due to the time constraint, it was decided to convert the four-cylinder engine into a single cylinder engine by blocking both intake and exhaust ports of the unused cylinders. The model-based combustion mode transition control algorithm was developed in the MSU HIL simulation environment and the Simulink based control strategy was implemented into the target engine controller. With both single-cylinder metal engine and control strategy ready, stable HCCI combustion was achived with COV of 2.1% Motoring tests were conducted to validate the actuator transient operations including valve lift, electrical variable valve timing, electronic throttle, multiple spark and injection controls. After the actuator operations were confirmed, 15-cycle smooth combustion mode transition from SI to HCCI combustion was achieved; and fast 8-cycle smooth combustion mode transition followed. With a fast electrical variable valve timing actuator, the number of engine cycles required for mode transition can be reduced down to five. It was also found that the combustion mode transition is sensitive to the charge air and engine coolant temperatures and regulating the corresponding temperatures to the target levels during the combustion mode transition is the key for a smooth combustion mode transition. As a summary, the proposed combustion mode transition strategy using the hybrid combustion mode that starts with the SI combustion and ends with the HCCI combustion was experimentally validated on a metal engine. The proposed model-based control approach made it possible to complete the SI-HCCI combustion mode transition within eight engine cycles utilizing the well controlled hybrid combustion mode. Without intensive control-oriented engine modeling and HIL simulation study of using the hybrid combustion mode during the mode transition, it would be impossible to validate the proposed combustion mode transition strategy in a very short period.« less

  • Molecular Tagging Velocimetry and Its Application to In-Cylinder Flow Measurements

    by Ravi Vedula, Mayank Mittal, Harold J. Schock

    This review article provides an overview of the experimental studies of in-cylinder flows using various flow measurement techniques with a focus on molecular tagging velocimetry. It is necessary to understand the evolution of large-scale and small-scale turbulence as prepared during the intake stroke with a cycle resolved quantitative description. Due to the difficulty in obtaining these descriptions, either by modeling or experimentally, they are often characterized with somewhat ambiguous notions of bulk swirl and tumble measurement methods. During the intake stroke, in-cylinder flows are formed in such a manner as to provide advantageous spatial and temporal behavior for mixture formation later during the compression stroke. Understanding the details of how these flows influence fuel-air mixing, the initiation of ignition, combustion, and subsequent flame propagation processes is the primary motivation for the development of the methods described in this paper. The authors provide an introduction to fundamental flow motion inside the engine cylinder and measurement techniques, e.g., hot-wire anemometry, laser Doppler anemometry, and particle image velocimetry. Furthermore, molecular tagging velocimetry is discussed in detail in terms of (i) different mechanisms, (ii) procedure and data reduction methods to obtain the desired flow properties such as velocity, vorticity, and turbulent intensities, and (iii) applications to flow studies in internal combustion engines. Finally, the significance of experimental investigations of in-cylinder flows is discussed along with possible future applications.


  • Development and Demonstration of a Low Cost Hybrid Drive Train for Medium and Heavy Duty Vehicles

    by Elias Strangas, Harold Schock, Guoming Zhu, Kevin Moran, Trevor Ruckle, Shanelle Foster, Jorge Cintron-Rivera, Abdul Tariq, Carlos Nino-Baron

    The DOE sponsored effort is part of a larger effort to quantify the efficiency of hybrid powertrain systems through testing and modeling. The focus of the DOE sponsored activity was the design, development and testing of hardware to evaluate the efficiency of the electrical motors relevant to medium duty vehicles. Medium duty hybrid powertrain motors and generators were designed, fabricated, setup and tested. The motors were a permanent magnet configuration, constructed at Electric Apparatus Corporation in Howell, Michigan. The purpose of this was to identify the potential gains in terms of fuel cost savings that could be realized by implementation of such a configuration. As the electric motors constructed were prototype designs, the scope of the project did not include calculation of the costs of mass production of the subject electrical motors or generator.