Lin Zhou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Lin Zhou has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Xiangrong Zhang
State Key Laboratory of Explosion Science and Technology, Beijing Institute of Technology, Beijing, China
3 shared publications - Hanfei Xie
State Key Laboratory of Explosion Science and Technology, Beijing Institute of Technology, Beijing 100081, China
2 shared publications - Tao Jiang
Chongqing Hongyu Precision Industry Group Co., Ltd., Chongqing 402760, China
2 shared publications - Yingzhong Zhu
Chongqing Hongyu Precision Industry Group Co., Ltd., Chongqing 402760, China
2 shared publications - Bo Yan
Research Institute of Gansu Yinguang Chemical Industry Group, Baiyin 730900, China
1 shared publication - Feichao Miao
School of Chemical Engineering, Anhui University of Science and Technology, Huainan 232001, China
1 shared publication
Latest Publications
- Open Access
Rheological Behavior of DNP/HMX Melt-Cast Explosives with Bimodal and Trimodal Particle-Size Distributions
As a matrix for melt-cast explosives, 3,4-dinitropyrazole (DNP) is a promising alternative to 2,4,6-trinitrotoluene (TNT). However, the viscosity of molten DNP is considerably greater compared with that of TNT, thus, requiring the viscosity of DNP-based melt-cast explosive suspensions to be minimized. In this paper, the apparent viscosity of a DNP/HMX (cyclotetramethylenetetranitramine) melt-cast explosive suspension is measured using a Haake Mars III rheometer. Both bimodal and trimodal particle-size distributions are used to minimize the viscosity of this explosive suspension. First, the optimal diameter ratio and mass ratio (two crucial process parameters) between coarse and fine particles are obtained from the bimodal particle-size distribution. Second, based on the optimal diameter ratio and mass ratio, trimodal particle-size distributions are used to further minimize the apparent viscosity of the DNP/HMX melt-cast explosive suspension. Finally, for either the bimodal or trimodal particle-size distribution, if the original data between the apparent viscosity and solid content are normalized, the resultant plot of the relative viscosity versus reduced solid content collapses to a single curve, and the effect of the shear rate on this curve is further investigated.
Open AccessRheological Behavior of DNP/HMX Melt-Cast Explosives with Bimodal and Trimodal Particle-Size Distributions
As a matrix for melt-cast explosives, 3,4-dinitropyrazole (DNP) is a promising alternative to 2,4,6-trinitrotoluene (TNT). However, the viscosity of molten DNP is considerably greater compared with that of TNT, thus, requiring the viscosity of DNP-based melt-cast explosive suspensions to be minimized. In this paper, the apparent viscosity of a DNP/HMX (cyclotetramethylenetetranitramine) melt-cast explosive suspension is measured using a Haake Mars III rheometer. Both bimodal and trimodal particle-size distributions are used to minimize the viscosity of this explosive suspension. First, the optimal diameter ratio and mass ratio (two crucial process parameters) between coarse and fine particles are obtained from the bimodal particle-size distribution. Second, based on the optimal diameter ratio and mass ratio, trimodal particle-size distributions are used to further minimize the apparent viscosity of the DNP/HMX melt-cast explosive suspension. Finally, for either the bimodal or trimodal particle-size distribution, if the original data between the apparent viscosity and solid content are normalized, the resultant plot of the relative viscosity versus reduced solid content collapses to a single curve, and the effect of the shear rate on this curve is further investigated.
- Open Access
Separate Calibration of Johnson–Cook Model for Static and Dynamic Compression of a DNAN-Based Melt-Cast Explosive
When describing the relation between the flow stress and plastic strain of a material under a wide range of strain rates and temperatures, the original Johnson–Cook model generally requires a complicated modification, resulting in a loss of simplicity and clear physical interpretation. In this paper, without modification, the original Johnson–Cook model was calibrated separately for the static and dynamic compression of a DNAN-based melt-cast explosive. The stress–strain curves for static and dynamic compression of this explosive were experimentally measured with a universal testing machine and a split-Hopkinson pressure bar, respectively. Based on the stress–strain curves, the flow stress vs. plastic strain data were extracted and used to calibrate the Johnson–Cook model. The calibration process is described. The parameters for the strain term, strain rate term, and temperature term were fitted sequentially. One set of model parameters was not able to fully describe the relationship between flow stress and plastic strain for both the static and dynamic compression of the DNAN-based melt-cast explosive. Two sets of model parameters were separately calibrated and compared for the static and dynamic compression of this explosive. The effects of the adiabatic temperature rise and the definition of the yield point on this calibration were also investigated.
Open AccessSeparate Calibration of Johnson–Cook Model for Static and Dynamic Compression of a DNAN-Based Melt-Cast Explosive
When describing the relation between the flow stress and plastic strain of a material under a wide range of strain rates and temperatures, the original Johnson–Cook model generally requires a complicated modification, resulting in a loss of simplicity and clear physical interpretation. In this paper, without modification, the original Johnson–Cook model was calibrated separately for the static and dynamic compression of a DNAN-based melt-cast explosive. The stress–strain curves for static and dynamic compression of this explosive were experimentally measured with a universal testing machine and a split-Hopkinson pressure bar, respectively. Based on the stress–strain curves, the flow stress vs. plastic strain data were extracted and used to calibrate the Johnson–Cook model. The calibration process is described. The parameters for the strain term, strain rate term, and temperature term were fitted sequentially. One set of model parameters was not able to fully describe the relationship between flow stress and plastic strain for both the static and dynamic compression of the DNAN-based melt-cast explosive. Two sets of model parameters were separately calibrated and compared for the static and dynamic compression of this explosive. The effects of the adiabatic temperature rise and the definition of the yield point on this calibration were also investigated.
- Open Access
An Inverse Analysis for Establishing the Temperature-Dependent Thermal Conductivity of a Melt-Cast Explosive across the Whole Solidification Process
Thermal conductivity is one of the most important thermophysical properties of a melt-cast explosive. However, the temperature-dependent thermal conductivity of such explosives cannot be easily measured across the whole solidification process (including the liquid, semi-solid, and solid states). This study used an inverse analysis method to estimate the temperature-dependent thermal conductivity of a 2,4-dinitroanisole/cyclotetramethylenetetranitramine (DNAN/HMX) melt-cast explosive in a continuous way. The method that was used is described here in detail, and it is verified by comparing the estimated thermal conductivity with a prespecified value using simulated measurement temperatures, thereby demonstrating its effectiveness. Combining this method with experimentally measured temperatures, the temperature-dependent thermal conductivity of the DNAN/HMX melt-cast explosive was obtained. Some measured thermal conductivity values for this explosive in the solid state were used for further validation.
Open AccessAn Inverse Analysis for Establishing the Temperature-Dependent Thermal Conductivity of a Melt-Cast Explosive across the Whole Solidification Process
Thermal conductivity is one of the most important thermophysical properties of a melt-cast explosive. However, the temperature-dependent thermal conductivity of such explosives cannot be easily measured across the whole solidification process (including the liquid, semi-solid, and solid states). This study used an inverse analysis method to estimate the temperature-dependent thermal conductivity of a 2,4-dinitroanisole/cyclotetramethylenetetranitramine (DNAN/HMX) melt-cast explosive in a continuous way. The method that was used is described here in detail, and it is verified by comparing the estimated thermal conductivity with a prespecified value using simulated measurement temperatures, thereby demonstrating its effectiveness. Combining this method with experimentally measured temperatures, the temperature-dependent thermal conductivity of the DNAN/HMX melt-cast explosive was obtained. Some measured thermal conductivity values for this explosive in the solid state were used for further validation.
- 1 November 2011
- Published by Pleiades Publishing Ltd in Combustion, Explosion, and Shock Waves
- Vol. 47 (6) , 721-726
Comparison of underwater shock wave attenuation of a new insensitive high explosive with different explosives
A series of experiments is performed to compare underwater shock wave attenuation of a new insensitive and aluminized high explosive RS with TNT, JH14, and PBXN-111 explosives. A new model with a uniform expression is proposed to characterize the pressure-time histories of the explosives. Numerical results show that the new model is applicable for both aluminized explosives and ideal explosives. The correlation coefficients for fitted curves are verified by thousands of test data for different explosives, and the accuracy is above 0.99. The energy of the underwater shock wave generated by PBXN-111 and TNT characterized by the new model agrees well with available experimental results. In addition, the shock energy of the new insensitive and aluminized high explosive RS is higher than that of PBXN-11 by 13.4%. The general performance of underwater shock wave attenuation of the insensitive and aluminized high explosive RS is found to be better than that of TNT, JH14, and PBXN-111 explosives.
- 1 November 2011
- Published by Pleiades Publishing Ltd in Combustion, Explosion, and Shock Waves
- Vol. 47 (6) , 721-726
Comparison of underwater shock wave attenuation of a new insensitive high explosive with different explosives
A series of experiments is performed to compare underwater shock wave attenuation of a new insensitive and aluminized high explosive RS with TNT, JH14, and PBXN-111 explosives. A new model with a uniform expression is proposed to characterize the pressure-time histories of the explosives. Numerical results show that the new model is applicable for both aluminized explosives and ideal explosives. The correlation coefficients for fitted curves are verified by thousands of test data for different explosives, and the accuracy is above 0.99. The energy of the underwater shock wave generated by PBXN-111 and TNT characterized by the new model agrees well with available experimental results. In addition, the shock energy of the new insensitive and aluminized high explosive RS is higher than that of PBXN-11 by 13.4%. The general performance of underwater shock wave attenuation of the insensitive and aluminized high explosive RS is found to be better than that of TNT, JH14, and PBXN-111 explosives.